【DRC】Wheel Choke Stock Review

For Version up of Cutting Board Trailer

I bought this for loading three Off cars on a common Chinese cutting board Trailer.

If you load everything in front, the Handlebar will hit the handlebar or the shrouds will be overlapped, so I use it to hold it in place while shifting it.

The construction is crude. The Pipe is crushed when you tighten the Bolt through the fixed hole, and the texture is pricey. View detail

Simple Stopper

Basically, you can use it by fixing it to something I remove the Center console from my car and make my own stand for fixing it
I think it was originally intended for off-road vehicles, but it can also be used for 250cc 17in. on-road vehicles It was available
However, the tire width is going to be a little tougher as it gets thicker
Also, if the tire width is narrow, be careful not to interfere with the Brake Disc when the vehicle is tilted It seems to be necessary
It's a good product to use after understanding the various caveats View detail

Suppresses movement of Front wheel

When carrying Motorcycle on a Transporter, this product is unnecessary if you can cut the Handlebar and press the Front tire against the corner and fix it.

It is necessary for those who want to straighten Motorcycle and straight down.
If the Front wheel can not be fixed, it may move during transportation, the Tie Down may loosen and the Motorcycle may collapse.
Even when carrying a Front tire against a foldable Second seat such as High ace, the Front tire is Quantity : Pair (for Left and Right) It is safe to use this product because it may move to.

I have KX 450 F on Nissan's NV 200, but I removed the Drink holder at the back of the Center console, attached the Aluminum board and fixed this product on it. I install it between the driver's seat and the passenger's seat, but I can install it without particularly difficult processing.

Please install for the protection of Motorcycle and Transporter View detail

Simple design's Tire stopper

I bought it as a stopper of Front tire when loading off-road motorcycle in Transporter.
The photo shows the Front tire of WR 250 R (80 / It is like seeing 100-21).

This product "Stopper to keep Motorcycle from moving forward" , "Can stand on its own without using Side Stand" Please note that it is not a kind of item.

This product is a hole for fixing Bolt to the floor (Φ 8. 5 × 4 places) are free. I think that it depends on the material of the floor, but there is a feeling of uneasiness that it is likely to move if it is not fixed.
In my case I wanted to change the place to load freely, so I bought Aluminum board to replace the floor and made it like a photo. The place where I pasted the same FlooringMatte as the floor of Transporter is really Oshanti (Actually, Matte was just surplus). I cut and pasted the Rubber board as a nonslip on the back.

The width of Pipe is delicately distorted, Penetrating to Pipe and free Φ 8. The hole of 5 is bent, the welding of the bottom plate is subtle, the board is oblique - - And the solid I bought was bad accuracy.
Pipe's Penetrating hole was bent a bit.. Bolt does not get straight in (Tears)
Because it is only a thing that stops Tire, I think whether it is good or not, and even though it is a ready-made product, I have not failed puncturing and welding like this. Do your best.. I also thought that I was honest. (Lol)

■ Dimensions (mm)
Outer width of Pipe touching the floor : About 170
Pipe diameter : Φ22. About 4?
From the end of the bottom plate to the edge of Pipe : About 200
Hole for fixing Bolt on the floor : Φ8. 5 X 4 places (Holes on the bottom plate are Φ 8. 5 and Φ 14. 5 holes are overlapping and vacant. It seems that M8 ~ M14 can be used) View detail

Since I went out for the expedition of a Motorcycle well, this product purchased this product. When loading the Motorcycle into vehicles and moving, it could carry, where it fixed this product to vehicles and the Motorcycle is stabilized ve

Since I went out for the expedition of a Motorcycle well, this product purchased this product. When loading the
Motorcycle into vehicles and moving, it could carry, where it fixed this product to vehicles and the
Motorcycle is stabilized very much. Since the
products are also firmly made very much to details, it can use for a long time. How about trying [ you ] once, since I will think with
that it is convenient if there is this product in migration in the
Enduro race, a Transporter, etc.? View detail