【DAYTONA】Slanted-Number Bracket Review
Fits: YAMAHA CYGNUS X SR, YAMAHA CYGNUS X SR, YAMAHA CYGNUS X SR, YAMAHA CYGNUS X SR, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, SUZUKI SKYWAVE250 burgman LIMITED, SUZUKI SKYWAVE250 burgman LIMITED, SUZUKI SKYWAVE250 burgman LIMITED, SUZUKI SKYWAVE250 burgman LIMITED, SUZUKI SKYWAVE250 burgman LIMITED, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S, SUZUKI SKYWAVE250 burgman Type S,
limited edition car model
Use outside of conformity at your own risk. As a result, it was not usable at all.
The problem is my own judgment, and the Manufacturer is not at fault in any way, since I am using a car model other than the compatible one.
Since it is made of bent steel plate, it is less likely to break unlike aluminum ones.
Responses
Other reviews
I was finally able to correct the angle to a safe one.
[How is it used?
When the Japan number was installed on the number mounting bracket of the KTM390DUKEOEM, the red reflector was facing downward, and the reflector did not reflect the light from behind at night, thus compromising safety.
Was the one you received as per Image?
I thought I have seen similar shaped Bracket in OEM Parts for domestic cars (lol).
Was the installation difficult?
The mounting holes on the vehicle body side and the holes on the Slant License Bracket side were not aligned slightly, so the holes on the Bracket side were cut off by about 2mm on the one side with a file to make an ellipse to align them. To prevent the Bracket from coming off due to vibration, I used a type of nut with a loosening stop.
How was your experience with it?
The 20-degree tilt angle is perfectly matched to make the reflector's reflective surface perpendicular and reflect light well at night.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation point and hang:When diverting the product to a car other than the compatible model, it is recommended to measure the angle of the installation part with a protractor in advance to avoid mistakes.
View detail
A little RearMakeover!
Purchased in conjunction with the relocation of NumberSlate to a reflector position above the existing position It was
The reflector part is processed vertically in the middle of a slanted rear fender, so this product is not I did some small work on the Rear Fender side as it is, and bought the Reflector that I bought at the same time I installed it with the kit
The verticality of the OEM was undeniable, but I personally felt that the Refreshing was more cohesive We are self-satisfied
View detail
Impressions!
I wanted to change the look of the standard spec I bought it with the Reflector kit StylishType
The company has an exclusive version for each model of car, but the standard spec. reflector is removed I wanted to install it, so I fitted it, and I wanted another 10 degrees of slope I used rubber plates to increase the slope of the addition, but this was a poorly thought out addition We are honestly satisfied
View detail
Rise moderately
Although it is the order to fix Number to Bracket after attaching Bracket to the car body formally
Level that it is very painful for the thick fingers because of the narrow gap.
Even my own finger was much Large strange.
However, once installed it will be at a moderate bounce angle
Not feeling not too much Brown (Personal opinion) I wonder if it is OK.
View detail
Used with ZrX1200R
Motorcycle I bought in second hand was Fender Eliminator but because it was removed
License Plate Bracket is required and purchased here.
I will add Exactly to NORMAL's Fender.
I only have a little bit of angle to the ground. Compared to the commercially available Fender Eliminator, it is nearly at right angles at all.
I think that it is not necessarily flashy.
View detail