【RENTHAL】Handlebar MX/ENDURO Review
Almost same Position as OEM
The material is solid, so I had a little trouble drilling the holes, but I was able to install it without any problems.
Responses
Other reviews
Would recemond these to mx or woods users, have used them on other bikes and they hold up great!
I bent old handlebars and bought these. Did a lot of research and wanted a quality handlebar. I really like them.Really good quality. It looks good and feels good. These bars build confidence.Highly recommend Renthal. View detail
I love it
The Goggles bar is good, choose here.
At first, I installed it as is and rode it.
I felt it was too wide, so I used Quantity:Pair (for Left and Right) Cut each 10mm by 10mm with
Just right. 802mm→about 782mm
It was thick but lightweight.
View detail
Used by D Tracker
[How is it used?
Mounted on D Tracker.
Application:Motard race (Circuit,Dirt) ,Off-road,Touring
Handlebar width is not trimmed. (Use the width as it is.)
Many tumbles
Was the one you received as per Image?
As per the image. The height is about average for an off-road handlebar, taller than ZETA's 22.2mm Super Moto-LowMODEL.
Was the installation difficult?
There are many parts that need to be removed, such as the handlebar body, switches, throttle, etc. It will take some time, but if you have the enthusiasm to replace the handlebar, there will be no problem.
If you want to drill a hole for the switch attachment and trim the width of the handlebar, you will need a power tool and a thread saw, which will increase the difficulty.
In addition, there is no need to extend the Clutch Cable or Throttle Wire even if the Handlebar width remains the same. It can be used as is. (Can be pimped out.)
How was your experience with it?
This product is a Handlebar that is one of the Off-roadHandlebars with a normal height.
The higher the handlebar position, the easier it is to ride when standing in the Dirt Section. I felt that the higher the Handlebar position, the more stable the ride.
In order to shorten my time, I needed to be fast in the Tarmac section.
For this reason, we decided to introduce the Handlebar, which is low in height. (Super Moto-Low on ZETA CX bars)
On the other hand, for city driving and touring, the higher handlebar position allows for a more comfortable and relaxed riding position, so if you feel uncomfortable with the height of the OEM handlebar on MOTARD and TRAIL vehicles, you may want to introduce this product because of its relatively high handlebar height and easy driving. If you feel uncomfortable with the OEM handlebar height of MOTARD and TRAIL vehicles, you may want to install this product since the handlebar height is relatively high and easy to drive.
I have long arms, so I didn't feel uncomfortable even with the Handlebar width untrimmed, but if you feel uncomfortable with too wide a width, don't hesitate to trim the Handlebar width.
An uncomfortable feeling when gripping the Handlebar will hinder safe riding.
As for durability, I have crashed many times on both Tarmac and Dirt, and the Handlebar has never bent. (No high SIDE falls.)
Attachment to the Handlebar is also no problem.
[Included Parts:were they on?
Bar pad
[Was there anything that disappointed you?
nothing special
Point and hang of installation
Describe the hang of the switch box attachment, not the HandlebarBody.
Positioning for the Switch box (Anti-rotation) There is a projection for
If you want to use it for secure positioning, you need to drill a hole in the HandlebarBody. If you don't drill a hole in the handlebar body, it won't physically attach.
So, if you want to install the switch box without drilling holes, you can scrape off the protrusions on the switch box.
In that case, use the Switch boxMounting Bolt (Screw) It is important to tighten the screws as tightly as possible to prevent the switch box from rotating.
I've had to scrape off the protrusions in previous Handlebar replacements, but the Switch box spins slightly and I didn't feel any problems there.
In the case of hole drilling
Electric Drill
Drill (Φ5 or Φ6)
Jig for drilling
Cle 556 (substitute for cutting oil)
It is safe to work with the
If you do not have a drilling jig, you can use the
Hammer
Punch
Make an indentation in the hole with a punch to prevent the drill from escaping.
Then I concentrated on drilling.
View detail
The color is wrong-barpad
The quality of the product is excellent just by looking at it without being fitted. However, the barpad was delivered in red color unlike the picture, so I bought it again separately from other websites. The website needs to be modified. View detail
I think it's good
I selected it with reference to the size of ZETA's COMP Handlebar Motard-Low, which is the standard of the SEROW250.
It is fitted with a tilt-back position.
View detail