【ALCAN hands】Grip Φ22 Review

Satisfied considering the price.

[How is it used?
I bought this to replace a Grip that had been falling apart since purchase.
The vehicle itself is still in Restore, but my hands were getting black every time I touched the Grip, so I decided to use this inexpensive product for now.

Was the one you received as per Image?
As you can see in the photo, it is only packaged in a Vinyl bag, but this is sufficient for Net mail order sales.

Was the installation difficult?
The work of replacing the grip itself is not particularly noteworthy compared to other grips.
If I may say so, I felt that the Throttle side was slightly looser than dominoGripetc.
Grip bond is used in conjunction with Grip bond, so there is no possibility of exiting.

How was your experience with it?
It is still before driving on public roads, but I am still a little concerned about the floating with the Throttle cone on the Throttle side.
Wiring might solve the problem, but I don't have it on hand, so I'll give up.
Well, I am satisfied with the price.

[Included Parts:were they on?
This is the only product. Grip bondetc. must be prepared separately.

[Was there anything that disappointed you?
Well, is this how it is? I think.
I am satisfied with the Fit of the Clutch Side, although the Throttle side is a bit of an issue.

【Review】
Although there may be some vehicle compatibility, the Throttle side is somewhat uncomfortable.
The price of the product is probably fair, but considering the price, it is probably acceptable. View detail

Design that looks easy to grip

I chose a design that would be easy to grip and resistant to deterioration, avoiding a textured format that looks like a mere small pile of files. The inner edge of the Right Side Throttle required some modification, but I was prepared for that, so I was able to do it without difficulty. I had been using a deteriorated grip for a long time, so now that I have a new grip, it feels like it is absorbing my hand and not slipping, and I feel good just holding it. I wish I had replaced it earlier. I will observe the durability of the new Grip. View detail

For ALCAN hands Grip Φ22

Used for HA02 CUB No. Custom90.
ALCAN hands has always been my favorite for wires, but they are inexpensive, and yet the actual product is not cheap and looks and feels better than OEM. The length is also just the right size. (Some manufacturers often leave short lengths even though their products are good, so be sure to check the length carefully.) 。
There is also a groove through which Wire can be passed, making it easy to fix Wire.
It is not a vibration reduction type or anything like that, so the Rubber thickness is normally thin, but it should be enough for a CUB or moped. 。 If there is no extreme price increase, I will repeat this product next time.
Incidentally, the CUB issue of this type is Quantity:Pair (for Left and Right) Please check the Handlebar Pipe and Grip inner diameters carefully before ordering.
As a CUB newbie, I looked at other people's reviews and found that all CUBs are Quantities:Pair (for Left and Right) I believed it to be of the same caliber and spent a lot of money on it. View detail

Good for cheap.

I feel that this is a very nostalgic design. It looks like it would look great on an old Motorcycle (personally).
I put it on and loved it. View detail

RossiGrip?

[How is it used?
I changed it for Enduro race with SEROW225.

How was your experience with it?
The RossiGrip is famous in the on road world (although it's a Honda OEM grip).
Is it the same shape as It is the Grip of the laugh.
Because of the price, I feel like I could replace it every month.

How did it compare to other products?
The real thing still looks cheap, but it looks like RossiGrip itself lol.
I don't think it's that bad, but it's pretty soft.

[Points to note]
It's cheap, so don't hesitate to use it and replace it. View detail