【MALOSSI】Multi-Variator 2000 Review
Great sports variant
Responses
Other reviews
สินค้าดี ใช้งานงาน ในการปรับแต่ง View detail
ใช่งานดี วิ่งสมูท สำหรับ ฺลูกใหญ่ View detail
It is very effective when properly installed in the right vehicle.
ZZ (CA1PB) I installed it in
As shown in other reviews, the Slide Piece will not Slide if assembled as is.
There seem to be many cases where the Slide Piece itself has been shaved hard, but take a closer look at the Ramp Plate. The outside of the U-shaped part where the Slide Piece fits into the Ramp Plate is narrow, and the Slide Piece is crushed in a direction that makes it narrower.
Therefore, shaving the outside of the U-shaped part of the Ramp Plate to the same size as the width of the Slide Piece saves a lot of work and eliminates the need to wear out the Slide Piece, which is already worn out from the start.
It is a good characteristic for a pulley, but it is a characteristic that connects from the bottom to the top at high rpm, so in the case of a 2-cycle engine, it will show its full potential only when a chamber is used. This is the reason why the High Speed Pulley is so good,
When an OEM exhaust system is installed, it is not so different from a general High Speed Pulley, and although the maximum speed is increased, the connection from acceleration to maximum speed is better with an OEM Pulley, so the cost-effectiveness is not so good.
It is good to see the speed increase slowly and steadily without losing the gradient even on a road that seems to climb gently.
By the way, WR6g, Chamber is reARAI's Shotgun modified, carburetor is OEM jetting only and ignition is Daytonablue box.
It is a good Pulley to build through the basic stages of Scooter modification.
View detail
I'm all about acceleration
When I searched for FORESIGHT 250, I could only find Malossi
I bought it for now, but if you use the weight roller that comes with it as standard, you can use it
The acceleration-oriented FORESIGHT is now even more acceleration-oriented!
I was reluctant to order the FORZASi Weight roller and other things from them
I adjusted the weight to just the right degree, but the maximum speed was slower than NORMAL
In the end, I was disappointed that the best solution to my frustration was to go back to Normal parts
View detail
According to reputation!
It's an exchange from ZERO's High Speed ??Pulley SS.
First of all, there are some BALI inside Pulley about installation. Also, Slide Piece is hard to move. There is slight BALI on the outside of the Ramp PlateRoller side.
Before installing, it is necessary to shave BALI and Slide Piece a little to improve movement.
The attached WR is written as 7 g. I hope not to use it, but (Lol)
As Belt also exchanged together this time, I think that it will not be evaluated only by Pulley, but installation improved and accelerating improved from the start clearly at the Belt companion stage.
WR used DrPulley and it was 5 g when Zero's Pulley was 5. Even if it weighs as much as 5 g it will accelerate and it will accelerate even a little richer uphill.
Also at the time of Pulley of ZERO, 2 mm color was added to a 36 mm boss and it was made long to 38 mm and it was pretty much dropped Belt, but this time put the attached 2 mm color into the Ramp Plate back to the Instruction Manual and put on the Pulley 36. I put a 5 mm boss.
I thought that the start and acceleration will fall as the Belt is not dropped, but on the contrary it got much better.
Although I can not evaluate fully-open running at the beginning of Belt's familiarization yet, I still think that Pulley can experience a considerable difference.
Both ZERO's Pulley and KITACO's Power drive kit are also used, but both are dissatisfied, but I think Malossi is the best in Total.
ZERO is getting a bit worse unless Belt is dropped at a high rotation speed and KITACO falls at the highest speed with low speed to acceleration focus.
Although I am high, though I thought that if I first added Malossi, it was cheaper to do it.
View detail