【ZETA】Replacement Mounting Kit Extended Size Review
It was too long although purchased to adjustment of the hand guard of the other company. There is sufficient die length to cut and also cut a screw thread. Compared with other manufacturers, it is merely square, and large.
It was too long although purchased to adjustment of the hand guard of the other company.
There is sufficient die length to cut and also cut a screw thread.
Compared with other manufacturers, it is merely square, and large.
Responses
Other reviews
Increases the Universality of Mounting Parts
hand protection like the recent Cruiser and RALLY50 cars, as well as long hours of use I installed it to make Riding comfortable
When I tried to install my ZETAHand guard, I applied it to the Radial I installed it because I can't install both Brake and Clutch due to the harm of installing master
The Bar End was installed with a slight twist, which bothered me a little I put it on to avoid Harness interference and got an acceptable angle! 。
View detail
I had PROTEPER SE bar handle Carmichaerl model and a bend type hand guard. This combination of standard size still installable. However, if I adjust to my best position, the master cylinder bolt interferes. I was not happy about the position and have been
I had PROTEPER SE bar handle Carmichaerl model and a bend type hand guard. This combination of standard size still installable. However, if I adjust to my best position, the master cylinder bolt interferes. I was not happy about the position and have been patient to use for a while, but enough! I decided to get new one. The installation is easy just exchange the mounting. However, the hand guard need to be modified a bit to make the installation easier.
Its curve need to be more opened. Of course it can't be done by hands, so I used a street ditch to bend it.
I put the hand guard and some protector cloths into the ditch hole then push-push. Actual change is not much, but it creates enough clearance to the extended portion.
I am more than satisfied! Finally I can ride with my best position. In addition I changed the clutch side too although it didn't have problems with standard size.
View detail
Since it exchanged for the diameter Fat bar of a large, and ラジポン, in a Mount of Armour Guard attachment, it was short and attachment was not completed. although it is die length easy [ attachment ] and delicate -- movable reservation of a Lever
Since it exchanged for the diameter Fat bar of a large, and ラジポン, in a Mount of Armour Guard attachment, it was short and attachment was not completed.
although it is die length easy [
attachment ] and delicate -- movable reservation of a Lever -- it was able to do.
Although it grasps and carries out and adjustment of ろ has merely become tight by セミラジ, if an angle is adjusted, it will be satisfactory somehow.
Although I think that
texture is not bad, it is thought that it is a little heavy Parts.
View detail
In the mount of attachment to an armour guard, since it may contact and loosen in a bolt when it is just before contact and moves by fall etc. to the banjo bolt of a brake, I purchased. However, I do not use it. It is too long slightly. It may be only for
In the mount of attachment to an armour guard, since it may contact and loosen in a bolt when it is just before contact and moves by fall etc. to the banjo bolt of a brake, I purchased. However, I do not use it. It is too long slightly. It may be only for the vehicle type which would interfere in it if enough space does not be kept. If it is several millimeters or 1cm should be just vacant, it has no necessity to purchase. If only suitable spacer like several washers is put and exchanging its part for the long bolt, it was enough length and this was unnecessary. If you can make a tapped hole, it just cuts to required length, and cut the tap, it would be ok... It is like "the greater hides the less". It was mentioned as 40 mm, if there is about 20mm, it was good. View detail
It purchases to D tiger X. In the case of the D tiger X, with the standard size of hand guard attachment, a right-hand side brake master cylinder and a left-hand side brake hose extraction part will interfere, respectively. Then, if this LONG is u
It purchases to D tiger X.
In the case of the D tiger X, with the standard size of hand guard attachment, a right-hand side brake master cylinder and a left-hand side brake hose extraction part will interfere, respectively.
Then, if this LONG is used, it can miss.
Attachment turns into fairly impossible attachment by the touch which drives away a hand guard quite ahead.
View detail