【SAITANIYA】Full Cowl Review

For Paint Base

[How is it used?
I was going to install a Chinese Cowl on my MC21, but after waiting for it to arrive after ordering, I cancelled the order and chose Saiya.
The OEM used Cowl is now enough to buy one Scooter....

Was the one you received as per Image?
Upper and SIDE (Under integrated) Of Quantity:Consists of 1 Set of 3pcs.
Screws and Nut for installation were included as described.
The finish of the paint is good because it is a gel coat that is supposed to be painted, but there are foreign objects on the edges. (probably a pool of FRP resin) The workmanship was not perfect, to be honest, because there were

Was the installation difficult?
In past Impressions, it was mentioned that the mounting holes on the Upper and SIDE were misaligned, but I had no problem with that.
Screws for fixing without any additional drilling (both with the body side, of course) could be fixed. (The photo shows a temporary fastening, so some parts may not be attached.)
However, Headlight could not be installed no matter how hard I tried, so I redrilled the fixing holes.
Also, unlike OEM, there are fewer Product Contents, which is good for ease of installation, but all SIDE and UNDER parts must be removed for maintenance.

How was your experience with it?
Material:The FRP is strong, so it is not at all PeLePera like Chinese Cowl.
As for the CowlDesign aspect, it is somewhat similar to OEM, so it is recommended for both preserving valuable OEMCowls and for Restore of vehicles without Cowl.
As expected, White Gel will float if left as is, so it would be good for those who can paint to some extent.

[Included Parts:were they on?
Screws and Nuts are included, but some of the fixing Rivet for the Screen and Fixing Screws to the car body are required separately.

[Was there anything that disappointed you?
It would have been a perfect score if only the finish on the edge and the position of the hole for the Headlight could be improved.

【Review】
Material:It is good that the FRP is strong and has little risk of breakage.
Although external cowl always has a hole position problem, I was able to install the cowl without any difficulty.
Since OEMCowls are becoming more and more difficult to obtain, it is quite nice to paint FRP Cowl in your own way. View detail

Under Cowl is a shame.

The upper cowl is squeezed inward near the radiator and interferes with the radiator cap, but the rest of the cowl fits without any problems.
Under Cowl has a bad hole at the bottom, and I am thinking of filling it with FRPRepair material to make it one piece and use it.
Upper Cowl and Under Cowl could be installed without any problem.
Material:I was prepared for the fact that there would be some hole matching and BALI removal etc. since it is an FRP product, but I am quite disappointed about the Under Cowl. View detail

Usable but subtle, that's what FRP is all about.

I was able to install it by adjusting the position of the holes.
Because of its age, the Meter Bracket and other parts may have been deformed by the fall, so you may need to bend or fix them to position them.
But isn't it a problem on Cowl's side that Under Cowl seems to interfere with Tire? I think so.
The finished product has a certain amount of raised and dented gels, so it might be a good idea to buy Pate and File together. View detail

The mounting holes don't quite fit.

I installed it, but it doesn't fit the screw hole of the car body at all.
It didn't fit even after a lot of tugging and pulling.
The mounting holes were machined and installed, but with the details in place, I was able to get the job done.
The Under and Front did not match at all.
In addition, I stopped Quick fastener forcibly, but it wrinkled up and down, and I was not able to use it.
It became full of gaps.
The whole product was terrible.

As a side note, I checked with my Race buddies and they said that the manufacturer in question is holding off on purchasing their products because of the variance in quality.
I wish I had known about this sooner. View detail

The product was great, but the distribution sucked.

I bought this from WehBig for Circuit Running.
Although I often use Cowl of Mr. Saigaya, accuracy is also good for a low price, and I am saved. If I were to say anything, it would be that the angle of the LeftMiddle cowl's body mounting screw did not match at one point. The product's a good one, no problems at all!

The reason for ReviewTitle is that I was very disappointed with the accidental product.
Of the Full cowl set that I received, the Upper Cowl was cracked from the ear to the tip of the nose. I got the impression that it was compressed during packing or transportation, and the upper ear etc. broke through the ball. As for the exchange procedure, only the damaged parts were sent back to Kanto, and it took a long time to send a good product after checking the condition.
However, the replacement Upper I received was damaged again. This time I hit the tip of my nose and the Gel layer was blown off. There are also cracks in the White Gel, which you can't see in the picture.

I had to work around my free time to build the vehicle, so I put a lot of work into rearranging the schedule and packing it back up.
Webig's response was that he was sorry he didn't inspect the car when it came in, and that he would take care of it.

I didn't really plan to write this much, but when I saw the accidental product I returned being listed on Yahoo as an unattached product, I was indeed annoyed. At the very least, could you please consider the User's psychology and do it in a place where it can't be seen?

Don't get me wrong, Saigaya's Cowl is a good product. We'll be using it from now on! View detail