【KIJIMA】IC Blinker Relay Review
No problem
I bought it for introducing LED Blinker
Exchange overseas goods via eBay due to rupture.
There is no problem after 4 years from the exchange.
I think there is no worry about durability.
Responses
Other reviews
Flashing relay
GSX-1000 L3 is installed.
Since Relay is in the Blue circle, it is easier to Rose Seat Cowl as much as possible, and since Relay itself has a protrusion to prevent it from falling out, Space is needed to knead it lightly with Minusetc.
Things are OEM same etc. and not so good or not so good.
View detail
BANDIT1200 2006 F/E used for LED conversion
I used BANDIT1200 FE Blinker LEDs and the only LED Bulb I used was JAPAN's Matsu Stripe. The price may be higher than Chinese products, but it is an old car and I thought it would be troublesome if I found a defective Chinese product, so I decided to go for peace of mind.
Front Blinker Valve Maz Stripe L820D OR
Rear Blinker Valve Mazda Stripe L820S OR
Tail lamp and License Plate Light have also been converted to LED.
Tail lamp bulb Maz Stripe L820D RE
License Plate LightValve Maz Stripe L742H
Relay can be accessed by loosening and removing the Left Side Cover with a single hex.
Tail lamp is located deep inside the cowl, so it was a little bit of a hassle to reattach it, but no problem.
BANDIT1250S Motorcycle Travel's blog was used as a reference. Thank you very much.
https://819oba3.com/bikelife/led-lights-bulbs/
*I was too lazy to look it up, so I looked at the blog and ordered the same thing without thinking w
View detail
KIJIMA KIJIMA IC Blinker Relay
Purchased to convert GSX-R1000 K8 to LED winker.
It does not become high flasher and is working fine.
It is a must for Blinker replacement.
View detail
MONKEY125 Sequential Blinkerization
Purchased to convert MONKEY125 (JB02) to Sequential Blinker.
BlinkerUnit is a Chinese product purchased from Ariek.
I bought a KITACO UniversalRelay (755-0400940), thinking that any Relay would do as long as it was LED and high flasher compatible, but it did not light up all the way.
Apparently, the blinking time is too short and it does not light up until the end (normal if it is a batch).
I wandered around the Net wondering what to do, and I found a post on this Relay review recommending it for sequential use.
I bought it thinking it would cure the problem, but the results were the same.
I think that JapanManufacturer products from DAYTONAetc. will shine until the end.
It seems that not all Sequential Blinkers, but the one I happened to buy was a Spec. that doesn't glow all the way through unless it is energized for a long time (Relay is not bad).
As a first aid measure, short the L and B terminals of Relay's Car Both SidesConnector, although the Indicator in the Meter will not flash (always on),
It is now glowing to the end.
We are currently waiting for an adjustable Blinker relay.
The range of illumination is similar to that of KITACO's Relay, and if used on a MONKEY125, the large size is not much different from the OEM,
I wonder if KITACO is better.
View detail
Mounted on TLR200 with 6?
Replaced with IC Blinker Relay to eliminate unstable Blinker blinking.
We chose KIJIMA's product because it is a 2-pole type and can be attached to a 2-pole car.
Works fine with HeadlightOff Idling.
HeadlightOn Idling works fine, although it affects other lights.
The ka-chica-chi sound will be eliminated.
We will check the durability and compatibility with the vehicle, but it worked almost as expected.
View detail