- Home
- Product reviews
- Motorcycle Parts
- Bodyworks
- Fairings
- Full Cowl / Exterior Set
- For the record, I bought it and failed... (A-TECH: Duct Side Cowl SPL For Race (1 Set Of 4-items))
【A-TECH】Duct Side Cowl SPL For Race (1 Set Of 4-items) Review
Fits: YAMAHA YZF-R25, YAMAHA YZF-R3
For the record, I bought it and failed
What made you decide to buy?
The Racer exterior of the YZF-R25 is getting a bit beat up, so I decided to buy a new one
Also, isn't the appearance of NORMAL kind of craggy?
I chose it because it looks very modern and Parenthesis
How was your experience with it?
When you run it, it flops quite a bit, probably because there are not a lot of threaded joints
I was worried about the knee part as well, as it would touch the exterior, but it was fine for running
Was it difficult to install? (In the case of hard parts)
This was the worst part
I didn't have an instruction manual or anything like that, but I installed it by image judgment The conclusion was that you can't catch it in NORMAL
Changed the position of the Handlebar from the top to the bottom of the Top Bridge and the Meter Bracket It didn't fit, so I had to beat it and deform it to get it to fit
Maybe it's actually attached, but there's no Construction Manual or I regretted it
What is the point or hang of installation (for hard parts)?
I don't know about now, but the Instruction Manual didn't exist, so the image I think you'll have to put it on at your discretion I don't recommend it if you are not confident that you will be able to fit it to the actual product
[Was there anything that disappointed you?
As I mentioned earlier, it's that there was no Instruction Manual The other thing is that no matter how hard I tried, I couldn't install it in the OEM position And that the exterior would flop when running
Do you have any wishes or improvements you would like to make for the Manufacturer?
I thought the instructions regarding installation were cursory
[Do you have any products to compare it to?
I used to use the Saigaya exterior before, and I still wish I had bought that again
[Others]
I believe this exterior is a Motif for the YZW-N6 exterior (Since it's the same A-TECH.)
It's nice to look at
It would be nice to be able to retrofit RAMAIR and Fresh air separately as well
สำหรับบันทึก ฉันซื้อมาแล้วไม่ผ่าน
อะไรทำให้คุณตัดสินใจซื้อ?
รูปลักษณ์ภายนอกของ Racer ของ YZF-R25 ค่อนข้างแย่ เลยตัดสินใจซื้อใหม่
อีกอย่าง รูปร่างหน้าตาปกติจะขรุขระไม่ใช่เหรอ?
ฉันเลือกเพราะมันดูทันสมัยและอยู่ในวงเล็บ
ประสบการณ์ของคุณกับมันเป็นอย่างไร?
ตอนวิ่งจะหลุดนิดหน่อยคงเพราะข้อต่อเกลียวไม่เยอะ
ฉันกังวลเรื่องหัวเข่าด้วยเหมือนกันเพราะมันจะสัมผัสด้านนอก แต่วิ่งได้ก็ดี
ติดตั้งยากไหม? (กรณีอะไหล่แข็ง)
นี่เป็นส่วนที่แย่ที่สุด
ฉันไม่มีคู่มือการใช้งานหรืออะไรทำนองนั้น แต่ฉันติดตั้งโดยใช้วิจารณญาณในรูปภาพ สรุปคือคุณไม่สามารถจับมันแบบปกติได้
เปลี่ยนตำแหน่งของแฮนด์บาร์จากบนลงล่างของท่อนบนและขายึดมิเตอร์แล้วมันไม่พอดี เลยต้องตีให้บิดเบี้ยวเพื่อให้พอดี
จริงๆอาจจะแนบมาแต่ไม่มีคู่มือก่อสร้างหรือเสียใจครับ
จุดหรือแฮงค์ของการติดตั้ง (สำหรับชิ้นส่วนแข็ง) คืออะไร?
ไม่รู้ตอนนี้แต่คู่มือไม่มีอยู่ เลยคิดว่าต้องใส่ตามดุลยพินิจ ก็ไม่แนะนำ ถ้าไม่มั่นใจว่าจะทำได้ ให้เข้ากับสินค้าจริง
[มีอะไรที่ทำให้คุณผิดหวังไหม?
อย่างที่บอกไปตอนต้นคือไม่มีคู่มือการใช้งาน อีกอย่างคือพยายามแค่ไหนก็ไม่สามารถติดตั้งในตำแหน่ง OEM และภายนอกจะพังเวลาวิ่ง
คุณมีความปรารถนาหรือการปรับปรุงใด ๆ ที่คุณต้องการทำเพื่อผู้ผลิตหรือไม่?
ฉันคิดว่าคำแนะนำเกี่ยวกับการติดตั้งนั้นคร่าวๆ
[คุณมีสินค้าที่จะเปรียบเทียบหรือไม่?
ฉันเคยใช้ด้านนอกของ Saigaya มาก่อน และฉันยังหวังว่าจะได้ซื้อมันอีก
[คนอื่น]
ฉันเชื่อว่ารูปลักษณ์ภายนอกนี้เป็น Motif สำหรับภายนอก YZW-N6 (เนื่องจากเป็น A-TECH เดียวกัน)
น่ามอง
คงจะดีถ้าสามารถติดตั้ง RAMAIR และ Fresh air แยกกันได้