【NBS JAPAN】Super Cub Leg Shield Review
It can be used without problems
Far cheaper than the OEM, and with a little work, it works just fine I have no complaints about the color However, the bolt holes on the Engine side are misaligned with the Large and need to be corrected After the modification, the hole is not visible We made a hole-filling plate with the cut-off part and repaired it with a high-performance adhesive (the one that exposes it to ultraviolet rays) It is too big And the part that is fixed with the plate at the back end is too big I feel that it should be corrected The performance is excellent, so if you can install it yourself, you can do it yourself "Buy I think so
Responses
Other reviews
I've had it for 8 years.
I installed it with Small machining and … what a surprise, I've had it for 8 years in its current state.
I've kept most of them covered with Cover, but even so, they've lasted surprisingly long; if they were OEM, they would be a shadow of their former selves.
As expected, recently it has become difficult to remove dirt and Black Mold grows under the Cover, but each time I put Dustcloth soaked in kitchen bleach and bleach it. This is a very good way to revive it.
For persistent stains, such as those from shoe hits, use Micro compound. In moderation." Taking.
I know it's cheap, so I should buy a new one, but I'm using it after modifying it a bit, so it's a hassle to replace it and modify it again, and I'm quite attached to it.
What's a bit of a surface white is the color loss and the decrease in transparency.
I recently noticed that it was originally Beige-ish. That cheesy color. was nearly bright White from sun exposure & fading over time.
The transparency is much less and no longer shows through to the Levels close to OEM.
The surface also remains smooth without any MicroCracks.
This made it even harder to replace them.
I heard that some lots of this product have a round BALI in the Center section (← did they change factories along the way?). I heard that some lots of this product have a round BALI in the Center part (did they change the factory in the process?), but perhaps the current distributed product has been solved by eliminating the BALI.
I can recommend it quite strongly because it is semi-durable and becomes more luxurious with each use (laughs).
View detail
Nice very Super cub50........................................... View detail
Leg shield LITTLE CUB
I bought this leg shield for SUPER CUB knowing that it needs some modification because of its low price. I installed it by shaving only the part near the handle. I was disappointed with the position of the bolt fixing holes at the foot. I wonder if this is a defect of only the product I received? View detail
As a Leg shield for CUB PRESS
It's deformed a lot on the inside, and in the winter, the wind will be stronger against your knees.
I installed each part with temporary fixation, but the position of the hole did not match, so I had to process the long hole and
I had to drill new mounting holes.
But for less than half the price of OEM, it's good enough for Cost performance!
I'm not angry because I imagined this much from the beginning (hole misalignment and deformation).
I think anyone can install it if they can drill the holes.
Best of all, it's much better than wearing OEM rags!
View detail
Price.
It's dry, though.
I bought this cheaper one because my OEM Leg shield was ruined.
good point
Cheap.
The position of the Bolt is neat so it is easy to install.
I thought it was easy to paint.
A bad point
●Thinner than OEM, so less strong.
So, it is easy to make a hole when you put Emblem.
The area around the exhaust system is easily deformed by heat.
As a solution, near the exhaust system, Cut or Paper is used to take a little clearance and make a gap.
Maybe it's wrong to compare with OEM because the price is low, but it's not as good as OEM.
As for Merit, I want to keep it inexpensive like I do. Or if you want to add some color to your Leg shield, it's good. Depends on how you use it.
View detail