【DRC】Wide Footpeg Motard Review
Fits: YAMAHA WR250F, YAMAHA WR400F, YAMAHA YZ125, YAMAHA YZ125X, YAMAHA YZ250, YAMAHA YZ250F, YAMAHA YZ250FX, YAMAHA YZ250X, YAMAHA YZ400F, YAMAHA YZ450FX, YAMAHA YZ85
It's just Steelfootpeg.
I used it on a wr250x 2007 model.
The spring that is sold separately is not fitting well with the yzSeries, and it became a Wide Footpeg, but because it is Steel, it is needlessly heavy, and the Slider is just a resin, so it wears out and disappears soon, and there is no need to have the Slider or not at all. I didn't feel the
Then I moved the footpeg to see if it would interfere with the Frame or Brake lever when I let it do full bank, and the footpeg was built to bite into the Brake lever installation Nut and LeverBody.
For $10,000, you can buy a yz250f Stainless Steelfootpeg.
I took it off and sold it after only 300k miles when it was installed.
This footpeg is not worth the price.
If it is about 2,000 yen, you may be satisfied with it if you are said to want a Wide Footpeg in fashion, but we do not recommend it to those who ride MOTARD firmly at all.
Responses
Other reviews
Items that can give a MOTARD feeling
The footpeg was bent in a fall and I had to replace it.
The rigidity is very good, but may be slightly heavy.
I think it is slip resistant enough, and since it is Wide rather than OEM, it is more stable.
Some may find it difficult to match the colors since the Slider is only available in one color, Red.
With OEM Pin or Washer, the gap is − the point where the OEM Pin or Washer would have a gap. For this price and car model Exclusive Design, I want Spacer.
View detail
Supermotard pegs
Love them! A nice wider platform, they feel reall good, and the grip is great on them. Easy to install as well. Bought it for the KTM supermoto project. I love the look and feel of the pegs. It's really cool. It has a clean black look with a nice red slider underneath to protect them. It fits perfectly with the stock shifter and brake levers. if you are planning to upgrade your footbrake lever we will at least use the lever I have. The latch mounting point is thicker than the stock and stops the brake lever from going all the way down. I simply grinded it in the area where my brake lever was touching and it now cleans perfectly. I haven't heard any complaints from anyone else on the subject, so it's probably the leverage I bought, so most won't have this issue. View detail
Look and feel
I bought it because I like the way it looks and I don't drive in a way that scrapes the Peg.
Grip is now more effective due to a wider surface for placement with the sole of the foot.
View detail
Performance and appearance are both ____.
Grip feeling with boots is better than that of ○OEM, and it is easier to hold the boots with the feet for riding.
×Boots' Sole is easily reduced compared to OEM.
Well, this place is at odds with the Grip feeling, so if you care about it, you lose.
The footpeg position is slightly raised to prevent rubbing during van king.
× Since the way up is slightly, rub normally during deep bang-king.
Perhaps it is not a product to prevent rubbing in the first place, but a product to reduce the feeling of drag when rubbing, so if you care about it, you will lose.
Slider section scrapes the ground. (Exchangeable) Therefore, they can be easily and inexpensively replaced when they wear out.
× Material is soft and reduces to a gurgle, perhaps to make it glide smoothly.
If you bank a lot, you can run Circuit all day long and that's it. If you think that's why you haven't had any accidents, the cost of replacing the slider is just a small amount of money. If you worry about it, you will lose.
The Appeal of "I'm going to bank my footpeg so much that I'm going to footpeg it!
When I put on ×this and the Slider is Polished, I get the "do you need that? I get a "do you need that?
Either way, I think it's high-profile. If you don't care about the way people look at you, you'll lose.
Very nice product
View detail
Small processing is required.
I was able to install it, but as it is, the Peg does not move to the upper side when paying STAND.
When the inside corner of Peg was shaved a little with Disk sander, it came to move.
I'm pretty happy with how it looks, matches the color of the car body.
View detail