- Home
- Product reviews
- Motorcycle Parts
- Bodyworks
- Rear Carrier
- NMAX125 2021 Application... (Givi Indonesia: Special Advance Rack SRV)
【Givi Indonesia】Special Advance Rack SRV Review
NMAX125 2021 Application
The print quality of the Manual is poor and the image is unclear. As for the installation, it was not possible to install it according to the manual, and it was necessary to remove the Cover. The installation work took about 1.0h, and if you are familiar with it, I think it will take less than 0.5h.
The problem is that after the Carrier is installed, the height of the ground surface behind the Seat becomes higher, so the Seat cannot be keyed unless the Seat is pressed hard from above. manual says to remove 3 Rubbers attached to the Seat, but both SIDEQuantity:2pc. The set can be removed, but the rubber is not installed in the center. 125model may have a different seat shape from 155.
Other than this point, I am satisfied.
แอปพลิเคชัน NMAX125 2021
คุณภาพการพิมพ์ของคู่มือนี้ไม่ดีและภาพไม่ชัดเจน สำหรับการติดตั้งนั้น ไม่สามารถติดตั้งได้ตามคู่มือ และจำเป็นต้องถอดฝาครอบออก งานติดตั้งใช้เวลาประมาณ 1.0 ชม. และหากคุณคุ้นเคย ฉันคิดว่าจะใช้เวลาน้อยกว่า 0.5 ชม.
ปัญหาคือหลังจากติดตั้ง Carrier แล้ว ความสูงของพื้นผิวด้านหลังเบาะนั่งจะสูงขึ้น ดังนั้นจึงไม่สามารถใส่กุญแจที่นั่งได้ เว้นแต่ว่าที่นั่งจะถูกกดอย่างแรงจากด้านบน คู่มือบอกว่าจะถอดยาง 3 ตัวที่ติดอยู่กับที่นั่งออก แต่ทั้ง SIDEQuantity:2pc ชุดถอดได้แต่ยางไม่ได้ติดตั้งตรงกลาง รุ่น 125 อาจมีรูปร่างที่นั่งแตกต่างจากรุ่น 155
นอกเหนือจากจุดนี้ฉันพอใจ
Responses
Other reviews
Installation instructions are confusing. (English Version)
The Installation Instruction Manual was difficult to understand.
At first, when I put it on thinking it was a replacement for the OEMGrab Bar, I bLOOVE it up and down.
It appears that the OEMGrab Bar is used and sandwiched between them to ensure rigidity.
Since the part where the OEMGrab Bar is sandwiched between the two gold elements, it is recommended to protect it with a thin rubber plate or the like.
(You could have at least included this.)
In case you are wondering how to install it.
Remove the OEM Grab Bar. (4 Bolt)
Remove the decorative cover from the top of the Tail lamp. (TappingBoltQuantity:2pc)
Place a GiviCarrier. (Not yet fastened)
Reinstall the lid on top of the RailLamp.
OEMGrab Bar sandwiched between GiviCarrier and Quantity:Set and fasten with the Bolt supplied with Givi. (Givi is bottom, OEM is top)
Fasten the collar and long Bolt so that the OEM Grab Bar is sandwiched between the collar and long Bolt with Givi. (You may want to protect the OEM by placing a thin Rubber between the hit areas.)
This makes it quite firm.
View detail