- หน้าแรก
- เครื่องมือ
- เครื่องมือไฟฟ้า
- SK11
- SK11: ดอกสว่านทรงกรวย
รายละเอียดสินค้า
รายละเอียดสินค้าด้านล่างนี้ใช้โปรแกรมแปลอัตโนมัติโดย Google Translate
แสดงต้นฉบับ
คุณสมบัติ
[วัสดุ]กรวย Flathead : เหล็กความเร็วสูง
เจาะศูนย์ : เหล็กความเร็วสูง
[รวมอะไหล่] ประแจหกเหลี่ยม 2.0 มม
[คุณสมบัติของผลิตภัณฑ์]
เส้นผ่านศูนย์กลางของ Flathead : 10.5 มม
เพลาหกเหลี่ยม 6.35 มม
ความยาวของดอกสว่านตรงกลาง : 15mm
เส้นผ่านศูนย์กลางของดอกสว่านตรงกลาง : 4.0 มม
มุมแบน : 90 องศา
ความเร็วในการทำงานสูงสุด : 2500 นาที -1
รุ่นที่สอดคล้องกัน : สว่านไฟฟ้า / สว่านชาร์จ / ไดร์เวอร์กระแทกชาร์จ [Material]
・Platter cone: High Speed Steel
・Center drill: High Speed Steel
[Components] Hexagonal bar wrench 2.0mm
[Product Specifications]
Counting diameter: 10.5mm
6.35mm hexagonal shaft
Effective length of center drill: 15mm
Center Drill Diameter: 4.0mm
Counting angle: 90 degrees
Maximum operating speed: 2500min-1
Supported Models: Electric drills, rechargeable drills, rechargeable impact drivers
[Standard] SHSD-4 4 x 10.5
รายละเอียดคำถาม
ด้วยหน่วยเดียวนี้คุณสามารถเจาะรูใต้สกรูและถอดแผ่นออกได้ในเวลาเดียวกัน ..
[ใบสมัคร]
เจาะรูเบื้องต้นสำหรับสกรูหัวจม + งานฝังพื้น
[คุณสมบัติของสินค้า]
ทำจาก HSS สามารถเจาะเหล็กอลูมิเนียมและไม้ได้และมีความทนทานสูง ..
ส่วนของตัวนับ 3 ใบมีดทำให้เกิดการประมวลผลแบบกลมอย่างสวยงาม ..
การยึดติดกับตัวขับกระแทกด้วยสัมผัสเดียวด้วยเพลาแบบหกเหลี่ยม With just one tool, you can drill and remove screws at the same time.
[Use]
Drilling and countersinking for countersunk screws.
[Product Features]
Made of HSS, it can drill holes in steel, aluminum, and wood, and is highly durable.
The 3-blade design of the chamfering section achieves beautiful, round chamfering.
Hexagonal shaft type can be attached to the impact driver by one-touch.
คำเตือน
* โปรดสวมแว่นตานิรภัยหน้ากากและถุงมือนิรภัยขณะทำงาน* โปรดตรวจสอบความหลวมของดอกสว่านตรงกลางก่อนใช้งานและขันสกรูให้แน่น
* กรุณาอย่าดันหรือเขย่าไปทางซ้ายและขวาอย่างแรงและอย่าให้โคจิลอยขึ้นระหว่างการชก *Always wear protective goggles, mask and safety gloves while working.
*Before use, be sure to check the center drill for looseness and tighten the set screw.
*During drilling, do not force the machine or shake it to the left or right to pry it out.
ทบทวน
0.0
/ 5
(0 ทบทวน)