Reviews
Easy to install
I had an Indicator, but I replaced it with this one. It's not very noticeable, but the price is low, so I guess it's okay! View detail
It is easy to install.
First of all, it looks better Parenthesis!
I think anyone can install it. It takes less than 5 minutes, even for those who are not used to it.
If I had my way, I would like to see it released in a variety of colors.
View detail
Limitations of Tie Wrap
It is a convenient way to easily see the movement of the spring and the amount of remaining spring until it bottoms out. The MC51 is a large size, which is the reason why it leaves a large amount of Damage on the seals. The MC51 has a quantity on the Left Side.:Set the Right Side to the Right Side, which has a caliper, and the Brake dust will bite the Sensor and damage the Inner Tube. View detail
Looks Custom
Circuit does not run, so it looks Spec! View detail
I'm glad I put it on.
It was quite tricky to install without removing the Fork and Cowl.
It was easy to put the hang only on the Spring first and cover it with the Ring later.
Tie Wrap has the same effect, but I was concerned about the appearance, so I went with the exclusive product.
View detail
It looks like a Large thing.
Tie Wrap can be used as a substitute, but I bought the special product because it looks better.
I couldn't understand the installation just by reading the Instruction Manual. (Lol) I've heard that you can think of Spring as being Screw at the end of Spring.
The Rubber Band was installed as if it were fitted to White-colored Parts.
View detail
Clumsy & difficult to put on if you have thick fingers (laughs).
For installation, as others have said, Spring and Body should be separate.
If you have thick fingers, you may find it strange to wear a large Spring.
Spring must be rehearsed by floating it in the air before vehicle installation.
As for the hang of achieving installation in my case, Package and others say that if you pull too much, the Spring will stretch, but I am so scared of that that I get into a negative spiral where I can't install it without pulling (lol).
I was prepared for it to fail and turn into Garbage, so I pulled it to the Large size.
It's expensive to Garbage (laughs).
Lastly, as a beginner in circuit driving, I wanted to see how far I could sink in full breaking, not to mention setting.
I considered using Tie Wrap substitute, but I was excited to purchase it because I wanted to reduce the negative impact on the Inner Tube.
View detail
Stroke volume confirmation
Installed to measure Stroke volume.
I could have gone with Tie Wrap, but I went with this one because of its appearance.
The main reason for our choice was that there were φ37 in the Lineup that could be used with the CBR250RR.
View detail
Instead of Tie Wrap
Tie Wrap would have been fine, but when I installed it, it was smoother than Tie Wrap, and I think it is cooler and easier to remove than Tie Wrap. View detail
I want to visualize the Stroke amount.
[How is it used?
I installed this on my MT-09 2017 model. 41Φ.
Change Spring in Front fork to Hyper pro and use it to visualize the amount of Stroke.
Was the one you received as per Image?
As per Image.
How was your experience with it?
Tie Wrap can also measure the amount of Stroke, but it is a self-satisfying addition of a component.
No particular complaints.
[Points to note]
As others have mentioned, installation is a bit tricky. Instead of installing it out of the blue.
I think it is better to practice only Spring to make a loop in the air.
For installation, only the Spring is wrapped around the Inner Tube, and then the Rubber Band is attached to the Slider.
We did it with the feeling of
How did it compare to other products?
There were cheaper ones than this item, but we chose this one because of the shipping cost.
I cannot tell the difference in performance and quality.
View detail
For Front suspension setting.
I installed it on the front suspension of my ZX-6R (2012) which is used only for circuit driving, so I can see how much the suspension sinks and know the setting. I had it installed at the shop during the maintenance. It is an ordinary part, but it is very useful. View detail
Size Warning.
It's not a matter of usability or anything else.
The picture of the item on the front page is different in size from the original.
My mistake in not checking, but it must have been a factor in the mistake.
At least use a photo without Size.
View detail
Understanding the current situation of Front fork
I used to replace Tie Wrap so far, but the Stroke sensor taught me that I can attach it without having to break Front fork, I bought it.
Integra Le is that Metallica - Brake Pads' Auto studio MaleKill's product, so I thought that the quality is also reliable choice.
At the glance of installation, twist Spring which can not be seen twisted and install it in a form to wind around Fork 's Tube.
Because it is Small Parts, you need a little hang for installation, but you can do it easily if you do it carefully.
Before setting Front fork, you can judge how much you use Front fork by using this Sensor.
It is not necessarily for Race but I think it is a necessary part for understanding the current situation of Motorcycle.
View detail