Reviews
Light weight and accuracy is not bad.
Although it is obviously lighter than Steel, its strength is not a problem. When adjusting the split wheel, the Quantity:Pair (for Left and Right) If you set the center of the wheel of the "1" firmly, there will be almost no blurring. It's a pity that the Black color variation is no longer available, but I hope you will re-release it. View detail
Fits: HONDA CHALY series 10InchWide wheel (2.75J), HONDA CHALY series 10InchWide wheel (3.5J), HONDA CHALY series 10InchWide wheel (4.0D), HONDA CHALY series 10InchWide wheel (5.5J), HONDA DAX
Functionality is fine.
Purchased for use with Split Wheel. If you are not adventurous, you can use GCraft to put together the hub, Wheel, and Spacer. It says "Spacer" but it is not to be inserted in the Wheel. View detail
The sense of moderation is tight.
Our predecessors explained to us the complicated mechanism around the shift shaft and said that if it is installed, it is definitely recommended to install these parts to ensure fee rings and up-down and to prevent deterioration due to wear over time.
First of all, the product was supposed to be solid, but unfortunately, there was an uneven surface near the rear mounting area due to a fall.
The RearMounting Bolt is a part of the Gold seat, so I used a file to break in the part in question! I guess it could be a defect in shipping, but the manufacturer's packaging was also only in a Vinyl bag! I'm not sure.
The installation itself is simply a matter of replacing the supplied Hexagonal bolt with the supplied color, OEMPlus head bolt in two places as shown in the image, and then installing the product and fixing it in place.
When installing through the shaft, simply insert the shaft by greasing the inside side, then insert the attached collar between the Engine side and Guide side and bolt it in place.
The instruction manual said to apply a small amount of grease to the collar, so I applied it before installation and finally tightened the collar using the Manual Torque.
Already installed penske lighting footpeg (Barts commonly referred to as Rear Sets) and Guide were installed with no problems.
When installing, the usual precautions are to insert the Bearing and the Shaft on the Engine side. (Relatively loose, unlike normal Bearing insertions) goes in easily without any hardness or reluctance, I applied a small amount inside and on the surface of Bearing and installed it.
Since the bearings are ShieldType, it is important to pay attention to the shielding when inserting the shafts, as it will affect the maintenance and the life of the parts later on.
Although there is almost no play in the body when installing the guide, we fine-tuned and fixed it so that the bearing load is in a neutral position relative to the shift shaft.
After installation of the guide, return the shafts of the rear sets to complete the installation.
The shift was certainly a little lighter than the OEMShift, but after the Rear Sets were installed, a sense of moderation was felt, and a more solid feel was added.
In the test run, I was relieved to see that the − indicator on the GEAR intermediate display is no longer displayed on the Meter.
Even in the Practice Course, GEAR loss is virtually eliminated if the operation is not too lax.
The impression after installation varies depending on the wear and tear of the shift shaft, but it increases the sense of moderation and the certainty of shift operation.
View detail
Name Chain
To increase load capacity as much as possible, CenterCarrier was considered.
The CenterCarrier is also GCraft, as it is also equipped with a GCraft front carrier, to create a sense of unity.
The Plate area of Silver is quite large, so the impression you see changes at once and the Machine feeling becomes stronger.
The load capacity is said to be 1 kg, but there is room for maybe 3 kg.
The installation itself is easy, but be careful only to install and remove the bolt that attaches to the MotorcycleBodyFrame.
The Bolt is screw-cut so that it enters the Bolt at an angle, so if you do not do it carefully, you will break the screw threads.
OUTEX SteeringStabilizer is installed, but it interferes with the Handlebar when it is cut to the fullest, creating a dent. The surface finish is beautiful Silver, but it seems to scratch easily.
The system is compatible with the Mole System standard, so various bags can be loaded in a variety of ways.
View detail
Even JA65 is effective.
I once placed an order directly with the manufacturer, but the delivery date was more than a month later, so I had removed it from my priority list, but I happened to find it in stock at Webig while looking for other parts and purchased it immediately. The instruction manual is simple, but I think that people who install this kind of parts can install it without relying on the manual. Although it is not used very often, it also makes it easier to operate the half-clutch. View detail
Dirt-style Custom
It is easy to install. It is easy to install. It is the perfect item to distinguish yourself from others. View detail
The highest quality brake pedal available for the Monkey
About quality and texture, I can confirm the quality great and the material used is aluminum that is CNC machined to shape and finished with an all silver anodized coating.About the feeling of use, The highest quality brake pedal available for the Monkey. Not only does this pedal look superb when compared to the original Honda part but it also operates flawlessly improving the braking ability.Products to buy together, To complete the look the G-Craft shift pedal is a must to also add to your cart.Difficulty of installation, I can say the fitment of the rear brake pedal for my installation was easy due to the simple nature of exchanging the original Honda part with an aftermarket part that bolts into the same places without modification.Cost performance and comparison with other products, The pricing of this product is good, you receive a very high quality part that also works extremely well, no other brands offer an upgraded options for the Honda rearsets.About shipping and packaging, My order was shipped within 24 hours of the product being in stock and I received a few emails advising me of the status up until the order was dispatched. The order arrived within the estimated date range and was extremely well packaged. I found the link supplied to track my order very useful while I was waiting for the order to land in the country. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
The highest quality gear shift pedal available for the Monkey
About quality and texture, I can confirm the quality great and the material used is aluminum that is CNC machined to shape and finished with an all silver anodized coating.About the feeling of use, The highest quality gear shift pedal available for the Monkey. Not only does this shifter look superb when compared to the original Honda part but it also operates flawlessly improving the ability to shift gears.Products to buy together, To complete the look the G-Craft brake pedal is a must to also add to your cart.Difficulty of installation, I can say the fitment of the gear shift pedal for my installation was easy due to the simple nature of exchanging the original Honda part with an aftermarket part that bolts into the same places without modification.Cost performance and comparison with other products, The pricing of this product is good, you receive a very high quality part that also works extremely well, other brands offer cheaper priced options but not to this standard.About shipping and packaging, My order was shipped within 24 hours of the product being in stock and I received a few emails advising me of the status up until the order was dispatched. The order arrived within the estimated date range and was extremely well packaged. I found the link supplied to track my order very useful while I was waiting for the order to land in the country. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
A necessary addition to adopt the brake caliper upgrade
About quality and texture, I can confirm the quality great and the material used is aluminum that is CNC machined to shape and finished with an all silver anodized coating.About the feeling of use, A necessary addition to adopt the brake caliper upgrade. The front caliper support bracket has a simple design with a strong constructed that allows for perfect positioning and alignment of the Brembo caliper.Products to buy together, To complete the brake upgrade the addition of a Brembo 2pot brake caliper to your cart is also necessary.Difficulty of installation, I can say the fitment of the front caliper support bracket for my installation was easy due to the ease of access to the mounting points using the original fasteners and the included fasteners to secure the Brembo caliper.Cost performance and comparison with other products, The pricing of this product is great, you receive apart made from a high quality material and with a high quality finish. Most of the other brands offer higher priced options.About shipping and packaging, My order was shipped within 24 hours of the product being in stock and I received a few emails advising me of the status up until the order was dispatched. The order arrived within the estimated date range and was extremely well packaged. I found the link supplied to track my order very useful while I was waiting for the order to land in the country. Any concerns, cautions, or advice when purchasing, I have no concerns or cautions when purchasing from Webike. I cannot recommend Webike enough for the majority of your biking needs. They not only sell aftermarket parts and bike gear but also OEM parts for your repairs and servicing needs. View detail
The impression changes by a Large amount, and there are a few points of concern.
[How is it used?
I bought it to change one of the areas that I didn't like the look of the NORMAL DAX, and the change together with the Rear fender-less and Exhaust System has changed the impression considerably.
Was the one you received as per Image?
I am satisfied with the texture as per Image.
Was the installation difficult?
The installation is so easy that even a beginner like me can do it with a small one-hour job.
However, you must read through the Instruction Manual. This is because the position where the Fender is to be installed 10.5 cm from the bottom edge of the Outer tube. If you do not look at these parts, you may end up with unintended results.
How was your experience with it?
It was quite nice to be able to install Inner Tube's Guard-like Parts, etc., using the Bolt holes that removed the OEM Fender.
[Included Parts:were they on?
Instruction Manual is included.
[Was there anything that disappointed you?
The brake hose guide comes with an extension part that prevents the hose from interfering excessively with the Up Fender, but it still interferes somewhat, and the color of the black hose is transferred to the Fender.
It is a moderately priced product and would be better if this area could be improved.
【Review】
I have written a lot about it, but I am generally satisfied with it, except for the cosmetics.
I don't run in the rain, so I'm not sure how much it would change the practical aspects of the product, but at least as far as looks go, I don't think this is a product that would betray anyone who is considering making Up Fender.
View detail
Fits: HONDA CUB SeriesHorizontal TypeEngine 12V
Installed 5 speed assembly.
I have been having a bad shifting feeling especially in N⇔1st gear since I installed 5th gear, so I decided to install Firmly which had a good reputation on the Net.
Shift feel has been improved, but it is still not perfect. Is this the limit?
The GCraft logo is also included, giving it a very personal feel.
View detail
Hurdle is a bit high for a beginner to install, but the Rear area is quite Refreshing!
[How is it used?
The front and rear fender area of the DAX125 was heavy, so we installed a rear fender-less system in conjunction with the exhaust system replacement.
Was the one you received as per Image?
I am satisfied with the texture as per Image.
However, the fact that it has a reflector and the number angle conforms to the new standard was the deciding factor, so we decided to go with this one, even though it is a little expensive.
Was the installation difficult?
The installation itself is easy, but I thought the process of removing the OEM Fender was a bit of a hurdle for a beginner like me.
It was especially hardMODE to remove the OEM License Plate Light from the OEM Fender cover in order to use the OEM License Plate Light.
(I couldn't figure out the Coupler, so I ended up cutting a piece of the OEM Fender cover to separate the License Plate Light from the Cover.)
How was your experience with it?
After looking at Fender Eliminator Kits from various manufacturers, I decided on this product, and I think it was the right choice because it looks the most refreshing.
(However, if you bend down to look into the Bolt, you may be a little bit surprised by the number of Bolts.)
[Included Parts:were they on?
There was a Mounting Instruction Manual.
[Was there anything that disappointed you?
As a disappointment or request, I thought it would be new if the Instruction Manual included instructions on how to remove the OEM Fender.
The removal time was about three times longer than the installation time, so the Instruction Manual for the installation would be more useful.
【Review】
I have written a lot about this product, but I am very happy with my purchase.
Personally, the three things I did not like about the look of the DAX125 were the Exhaust System and the front and rear Fenders, so I was determined to purchase only those three items that I was absolutely satisfied with.
The License Plate Light is hidden inside the Fender, making it quite Refreshing, yet the Number angle conforms to the new standard, so it is a good product that does not make you feel guilty.
View detail
G-Craft 38501
For the first time I purchased a product of this brand. I was very pleased. Very good overall detail design. I was pleasantly surprised by the functional elaboration, namely, I liked the selection for the hexagon at the end of the stud to be able to tighten the nuts and not damage the connection of the two metals. We kindly ask you to add in the description that two parts are included. I recommend... View detail
Use with Endurance Rear Carrier
I was able to install this product with the Endurance Rear Carrier installed. If anyone is considering using this product with the Rear Carrier as well, please refer to the following ….
Quantity:Pair (for Left and Right) The bolt supplied with this product is M8×35 and the bolt supplied with the Endurance Rear Carrier is M8×50, so when installing both, it is better to extend the bolt by 5mm or more, so the M8×60 bolt purchased at a hardware store was used. The torque of the bolt is 24N-m, which is stated in the instruction manual of the Rear Carrier, so make sure to tighten the bolt firmly.
The maximum load weight of the Rear Carrier is 8 kg, so the weight of this product (Quantity:Pair (for Left and Right) I think it can carry about 6 kg, taking into account the weight of the bag (about 2 kg in the case of the "C").
View detail
Cost performance is the best as Universal!
If you purchase the end rubber at the same time, you can use it with most of the M6 Bolt Rear Sets' Change Pedal and Brake pedal. View detail
Fits: Others , HONDA MONKEY R, HONDA MONKEY, HONDA DAX, HONDA CHALY, HONDA BENLY , HONDA APE
Cost performance is the best as Universal!
If you purchase the shaft at the same time, you can use it with most of the M6 Bolt Rear Sets' Change Pedal and Brake pedal. View detail
Simple is the best!
From NORMAL
It was quite Refreshing!
Design is
I like it very much!
Installation is not difficult.
Due to the large number of Bolts in the structure
We need to think about the order of the tasks.
It may take some time.
Once installed.
It is quite sturdy and sturdy.
Shaking while driving or
I didn't think Bracket would break!
View detail
Peace of mind for a long ride.
It is made by Gee Craft, a trusted manufacturer, so there are no problems with accuracy.
There are similar products at about half the price, but I was not sure if they were accurate enough, so I chose this product.
I think it is Large sturdy as it is OEM, but it is also a place that is frequently stressed, so there is a sense of security in terms of reinforcement.
We could not experience any shift change due to the installation.
If you expect the ScauperScauper feeling of *Change, you will experience it better with the Clutch adjustment.
View detail
Excellent
Hello everyone, this is a good product and I recommend it to everyone. This product can play a better role in braking .This is 100% original, you can buy with confidence. View detail
Braque is …in JAPAN!
It's Brake related. There are made overseas at half the price, but …hey….
Rather than regretting it later, I chose something that I could use with peace of mind. I am satisfied & relieved. However, I thought that the cutting marks were rather conspicuous, as was the front support. I was not disappointed with the Objection. Maybe it is because it is a hard material.
View detail