Reviews
If you want to go Stylish, this is it!
Refreshing the Fender area of the CB250R
Fender Eliminator from 3Manufacturer as far as I know Kit is out, but I chose Adio's because it was the most Refreshing
There's nothing difficult to install, but this Kit allows you to install the license lamp You need to crimp the terminals yourself and you need Electric Works Pliers
It's very stylish and stylish as well because the long Fender is gone The only downside to this is that it's still pretty dirty
I only ride on perfectly sunny days, but even so, when I get off the Motorcycle, the Tail Not only the lamp, even the tandem seat is covered with small stains Parenthesis is good, so it's fine..
This product is a great recommendation for people who don't mind a little bit of dirt However, I can't recommend it to those who ride on a rainy day
View detail
To the horror of static elimination!
This is an addendum to the in-play
I felt a decrease in torque at high speeds, so I changed the MJ immediately
As a result, it's back to the way it looked before the product was installed
But how things have changed, as far as the high speed range is concerned
Raising the MJ did not change it, it simply went back to the way it was
Where did the gas for the MJ raise go?
I'm sure it's being de-energized in a place I can't feel (Laughs)
Also, the stakes have changed with the MJ exchange
When you open the Axel from a standstill, does it feel like you're going to come forward much more forcefully?
That feeling will continue until you get on Speed to some extent
More carburetorQuantity:If you boil the Set down, you'll be able to experience the changes in all areas, but the maze
I'm going to stop because I feel like I'm getting lost
I'm happy with the changes I've experienced in my current state, at least a little bit
But still, I'm afraid of the power of static elimination
View detail
It's changed!
I installed it on my LEAD 100
Two in the front fork, one in the rear suspension, and
I felt Front had changed with HaDrill
I've been picking up the fine Gap and getting through to the Handlebar
That's gone
Even Scooters are different, and I'm Big Li
By the way, I don't think there's enough Rear to experience it...
View detail
carburetorQuantity:Set has changed
I installed PWK28 on my LEAD 100 and this time I installed this product
LEAD is a long Manifold anyway
NORMAL, of course, because of the longevity of the mani that I one-off to my for PWK28
i installed 2 places in total on the carburetor side and the Lead Valve side
When it comes to the test drive, low speed, medium speed, it doesn't feel any different than before
The biggest change I felt was in the high speed range, the torque seemed to be thinner... (-_-;)
Looking at the plug, it looks like White
The air that was being pulled by the mani due to static electricity is gone, and the amount of air entering the Engine has increased Isn't it?
Now, let's see if we can't make an MJ exchange
I hope it turns out to be a good one!
View detail
It was already de-energized …
When I checked NGCJapan's homepage, I found out that Front I bought it because it was listed as a good one in the forkBottom Shaft's Fixed Bolt
Installed to RZ-R's Fork bolt and test ride
Apparently it was already de-energized and I couldn't feel the effect
Actually …
Nut to Rear Chain Adjustment Nut to Others also static eliminator Nut
Indicator Volt also has a static eliminating Bolt
Is it too much power removal?
Others may say they can't feel the effects
Isn't that already neutralizing static electricity?
Recently, Bridgestone and Michelin Radial have had a conductive Slit on their Radials
You can see the conductive slit on the Left Side (STAND side) from the Center of the Tire
The effect will be less effective if that conductive Slit is removing static electricity
So check your Tire once!
View detail
It is an essential item.
I installed it on my Swish LIMITED Officially it is not possible to install it, but it can be installed without any problem Of course it can be operated with no problem View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Convenient to have
I remembered that it was attached to DIO and other OEMs, so I put it on
I think it's almost as convenient as you'd expect during a railroad crossing or a stop on a hill at a traffic light
However, I would like to see a long bolt included in the package if possible
And I wish I could lock it with my Left hand index finger, but Lever is too far away to reach it
It's a shame that I end up having to lock it with my Right hand while holding the Brake
View detail
Refreshingly, it makes you look better!
I worked from the information on the Net
Blinker's Spacer installation is the hardest part
Other than that, it wasn't difficult
As far as quality goes, the quality of the paint is a little poor and peels off easily during the process
What I'm interested in is the angle of the License Plate
That's pretty challenging
View detail
Fits: YAMAHA MAJESTYS, YAMAHA SMAX (SG52J), YAMAHA SMAX (SG28J), YAMAHA SMAX (SG271)
Difficult Installation Instruction Manual
The Installation Instruction Manual is very difficult to understand
The picture of the sample is also WhiteBlack and Small, so it's hard to tell
Mud Guard processing is also required, but there is no mention of it
The Installation Instruction Manual is useless, so I'm going to have to tear it all down and check it all out The work took four hours
I'm a mechanic, although I specialize in 4-wheelers
It's been a long time since I've had to install supplies with such difficulty
I ended up installing it with some difficulty, but ordered another product that didn't require any machining
View detail
Fits: HONDA PCX125 JF84, HONDA PCX125 JF81, HONDA PCX HYBRID, HONDA PCX150
Installed on JF81 PCX
To install, remove the entire rear cowl and use the license It is necessary to cut the resin of the Plate Light section, so it is necessary to use the ultrasonic cutter and It is more beautiful if you have File etc
After the installation, New Model PCX has a thicker rear tire Rear view is parenthesis good without complaint
It's completely visual
However, I think it would be more upscale if the Number angle was more subdued
The bad thing is that the Seat lock section will be completely empty, so if you try to run it on a rainy day, you'll be able to get the Muddy water will get into the box In addition, sand will bite into the grease in the seat lock section
You need to make your own lid from the inner fender side
View detail
Static Elimination Part 1
Aluminum Tape (Made in 3M) I'm doing a little static elimination at
Buy it as your next Items
Easy to replace The price is a bit high though
Aluminum Tape does not eliminate static electricity (I can't put it up.) Another advantage is that it can be mounted in place
View detail
It is quite good.
I can't cut off the Fender, so the Fender Eliminator Kit is very Recommendation ⌒⌒⌒
The communication from shipping to arrival was very thorough and very reassuring!
View detail
Fits: SUZUKI Address125 (2BJ-DT11A), SUZUKI Address125 (2BJ-DT11A)
For parking lock on the rear brake
You will need to remove the cowl around the Light as it is installed on the Scooter As there is no detailed information about this in the product manual, please refer to the service manual for further investigation is required
In my DT11A, the black cover part under Lever interfered with this product So I had to remove about 5mm
That took about two hours
I am satisfied with the function
View detail
Fits: HONDA PCX125 JF28, HONDA PCX125 JF52, HONDA PCX125 JF56, HONDA PCX125 JF81, HONDA PCX125 JF84, HONDA PCX150 KF12, HONDA PCX150 KF18, HONDA PCX HYBRID 2AJ-JF84
Very easy to use
It is very useful for stopping and parking on hills
And look "P" I like the fact that it's a letter of the alphabet
When we changed the lever to the adjust lever, there was not enough space for the lever to pass through
Bend it once to bolt the upper side and then bend it again to bolt the lower side
It was necessary
It's a little distorted, but it works fine
View detail
Neatly organized around the rear
Installation is pretty Large weird If you have power tools "Cut" "Cut" I think you can save a large amount of time with the process of
If you can take the time, I think it's possible to use Saw and File etc. without power tools
Drilling is required for installation, so you need to have a drill
It takes a lot of time and effort, but you'll be thrilled when it's completed
Disassemble again by re-tightening the mounting screws when they come loose
I shudder to think of what I would do I wanted to have at least a screw loosening stopper included
View detail
Making is good for the price.
Purchase to get Fender for GSXR 125.
I was worried because it was cheaper than those of other companies, but the making was firm without BALI, and Screw Pitch etc was easy to install because of insanity.
However, since there was no Space like Reflector 's Bracket which can put two kinds of Seals, Performance only ★ 4.
View detail
Fits: HONDA GROM (JC61) *Not available for MSX of ThailandSpec.
ADIO's short tail license plate stand is on time~
The MSX125 with this short-tail rack is so handsome. The original one is too ugly. I looked at it on Taobao and found that the quality is not ideal. Later, I found this car on the webike. Corresponding to the modified parts, I decisively started with this short-tailed card rack and some other small things. The logistics is still possible. It only took 5 days from order to hand~ MSX125 with this short-tailed card rack is really handsome, the original factory is too ugly, looked at Taobao, are the quality of the cottage factory is not ideal, and later found my car on webike Corresponding to the modified parts, decisively start this short-tail card holder and other small things, logistics can still be used from the order to the hand only took 5 days ~(translated by Google Translator) View detail
Bolt is too suspicious
Before injection injection Bolt has used it
Even at over-the-counter sales, it is also a product that can be sold with confidence that it may be decided not to buy it after purchase by DIO
This time there are things that Reduce shipping fee is over 3,000 or more
I tried to buy it for Rear suspension
After all the ride feeling has improved somewhat.
Next time I will look at the opportunity and I will attach it to Front fork
View detail
Design and Size are good, but - - -
I got lost in L and M, but it was just good with M. but - - - Weak adhesion has come off from sharp corners. I am sorry I like ADIO's Logo. View detail
Perhaps it is good - - -
I tried dubious Parts
Fitted on Inolon's Bolt
I did not understand the effect clearly because I fought other together
I think I'm probably getting better
I thought that I could also make my own if welding could be done I lowered the evaluation slightly from the price
View detail