Reviews
Fits: MOTOGUZZI V85TT, APRILIA TUONO V4 1100, APRILIA TUONO 660, APRILIA SHIVER 900, APRILIA RSV4 RF, APRILIA RSV4 RR, APRILIA RS660, APRILIA DORSODURO 900
[Color] Only Clear is useful.
I was concerned about the reflection, so I applied Antiglare first, but the lack of transparency made it very difficult to see the screen, so I removed it immediately. It is dangerously hard to see.
[Color] I am satisfied with Clear in terms of screen protection as I can't even tell if it is attached or not.
Antiglare was Garbage.Quantity:1 Set of 2pc. if available [Color] I think I'll just use two Clear cards.
View detail
Fits: HONDA 400X, HONDA CB500F, HONDA CB500X, HONDA CB650R, HONDA CBR400R, HONDA CBR500R, HONDA CBR650R
Difficult to apply neatly, but highly effective.
Non-glare film was used because daylight on the meter obscures the LED display. The film is highly effective and ensures visibility of the meter except when it is exposed to strong direct sunlight. However, due to the Film, the LED display looks a little dim.
Also, as mentioned in the Impression by others, film application is difficult. The difficult part is positioning the film and removing air bubbles. If you fail to do this properly and repeatedly reapply the film, it will lose its adhesiveness and peel off easily.
The first time I used this product was about 2 years ago, and although I reapplied it several times, it was slightly tilted against the meter panel and left several air bubbles, which was a compromise. Still, it has not peeled off after more than 2 years of use.
We decided to use this Film on our new vehicle. Basically, I followed the Instruction Manual (English Version only) that came with the product.
In this case, I used Mending Tape vertically on the right edge of the meter panel as a guide to position the film. After peeling off the protective film, lift up the film attached to the panel from the Left edge (do not peel off the entire film, as this will leave air bubbles). Then, I applied it again from the Right Side while pressing it with my finger to remove air bubbles, and was able to make it quite satisfactory. The spatula attached to the product is difficult to use.
View detail
Recommended for those who ride in the rain, such as commuters.
I think it is effective Large for those who ride to work etc..on rainy days like Title.
I never ran in the rain. (Impact of increased telecommuting) It will be a decision of about 5? on the way back.
I think the effect was to reduce the amount of dirt on the exhaust pipe and cylinder fins.
In my case, it may be a mistake when adjusting to Fender, but it is a little Quantity.:Pair (for Left and Right) Clearance of the "A" was different, but I think it is a resin molding product, so it is totally acceptable.
I used the supplied double-sided tape for 12 hours of crimping and 2 pieces of the supplied Nylon rivet just to be safe.
Double-sided tape is divided into parts, and the instruction manual makes it easy to understand.
I have a Nylon rivet, Φ4Drill to drill the hole, but I think you need to be careful about the position of the hole, the length of the neck and the push of the Rivet is the limit and it was hard to insert. It is recommended to find a good position as thin as possible. I was just eyeballing it, so it was at the limit. Also, Rivet is convenient because it can be inserted with bare hands.
View detail
Fits: HONDA CB1000R
Size is perfect
I bought it because I was worried about scratches on the meter panel. It was well made and the size was perfect. Quantity as expected.:I'm glad I had two of them because the first one failed. I'm not sure how to use the different colors, but I'm satisfied. View detail
Fits: YAMAHA XSR900, YAMAHA MT-09 SP, YAMAHA MT-09
Quantity:It comes in two sets...
Shortly after I bought my new car, I looked into various anti-scratch seals for the meter, but I was not satisfied with the results.
In the end, I decided that a dedicated product was the best choice, and although I hesitated because I thought it was rather expensive, I took the plunge and bought it.
[Contents] Is Quantity:It includes two sets of instructions and a translation of the pasting procedure (please type in the translation here).
I'm not very good at precision work, and I often make mistakes with the protective seals on my phone, so I tried to do better this time, but... I still failed because of the Dust in between (tears).
Later, I realized that there was a Seal for Dust removal, but it was already too late, and I had another Quantity:I'm going to try to Challenge at a later date with Set.
I'm currently using Antiglare, but to be honest, I don't find it very easy to read...
I'm looking forward to Super clear.
View detail
Fits: TRIUMPH Thruxton, TRIUMPH Street Cup, TRIUMPH Speed Twin 1200, TRIUMPH BONNEVILLE T100, TRIUMPH BONNEVILLE T120
Pear
I put it on my '19 SpeedTWIN.
The surface of the meter is curved, so it may be a little difficult to work with.
You can position it by lightly misting it with soapy water, and then use a dryer to lightly warm it up and remove the air.
It comes with a spare so you don't have to worry if it gets damaged.
View detail
Hmmm... I wanted it to be at least 5,000 yen.
The OEM Inner fender was short and I was worried about the dirt and the Rear suspension.
I thought it was a bit expensive, but I couldn't find any other suitable products, so I took the plunge and bought it.
I couldn't trust the tape that came with the product, so I used my own 3M Ultra Strong Double-Sided Tape, but the first time I put it on, I put it on a little off, and it started to peel off, so I put it on again so it wouldn't shift, and now it's somehow stable.
To put it bluntly, the product itself is just black hard plastic, and I think it's worth at most a couple of thousand yen. It's more effective than nothing, but after the rain, the mud is still bouncing around.
If you had sold it for at least 5,000 yen, I might have been satisfied...
View detail
Fits: HONDA XL750 Transalp, HONDA X-ADV, HONDA FORZA 750, HONDA CB750 Hornet, HONDA CB1000R
The air can't escape.
It is a protection that does not reflect sunlight and does not change visibility.
I've re-stretched it several times, but there are inevitably areas where the air can't escape.
I gave up because of the small bubbles.
View detail
Fits: HONDA NC750X, HONDA NC750S, HONDA NC700X, HONDA NC700S
Extender Fender
[How is it used? Extension for short FFender.
Was the one you received as per Image? usually
How was your experience with it? usually
[Points to note] The Pin of the resin is poor.
How did it compare to other products? None
Other items that would be helpful
Point and hang of installation/Items to be purchased together/Opinions and requests to Manufacturer None
View detail
Fits: TRIUMPH Tiger 900 Rally Pro, TRIUMPH Tiger 900 Rally, TRIUMPH Tiger 900 GT Pro, TRIUMPH Tiger 900 GT, TRIUMPH Tiger 900 Rally Pro, TRIUMPH Tiger 900 Rally, TRIUMPH Tiger 900 GT Pro, TRIUMPH Tiger 900 GT
Is it a work sKill problem….
I was not able to put it on without any air bubbles, but I was able to put it on without worrying about it. At any rate, it looks so much better than without it. [Color] I feel Clear. View detail
practicality
I'm sure it will look bad, but it is practical. I don't have a photo of it as I don't have a vehicle at hand, but it has reduced the amount of mud splashing from stepping stones. I asked a motorcycle shop to fix the Rivet so I didn't have to worry about it falling off. If you are looking for something practical, this is the Recommendation. View detail
Fits: YAMAHA MT-09SP, YAMAHA MT-09
I don't want you to sell this stuff.
The Antiglare is still usable, but the UltraClear has a strange cut, and the Right Side is clearly cut with a gap. I have no choice but to use Antiglare.
I wonder when they will be able to make a decent product. 4000 years of history is nothing.
View detail
Fits: HONDA CBR1000RR FIREBLADE, HONDA CBR600RR, HONDA CBR600RR
slightly elevated
Instruction Manual is also available for easy application.
If you've ever put a Cover on your phone...
I don't even need the Instruction Manual!
The size is exclusive and perfect.
I thought the price would be a little lower.
Recommendation for dedicated and easy installation.
If you are dexterous enough, you can make it by yourself.
View detail
Fits: TRIUMPH Thruxton, TRIUMPH Street Cup, TRIUMPH Speed Twin 1200, TRIUMPH BONNEVILLE T100, TRIUMPH BONNEVILLE T120
Not compatible with curved surface Meters.
I would like to leave it here with some unnecessary information to make it useful for all BonnevilleUser.
I bought my T120 in 2021, but the fitment was '16 and up.
This product is imported by Peitzmeier, so it seems to be the same product as described there.
Now, the Film is listed as only 2 copies, but the one I received was Quantity:1 Set of 4pcs.。
already ? is.
At that time I still consider myself fit.
Read the Instruction Manual carefully and try it with excitement and caution, and you'll never have to worry about small scratches on your Meter again!
Come on, let's clean the Meter.
Wipe it off with the included WetSeat. So far, so good. A little watery. Okay, now for the CROSS.
"…wipe……?"
No, no way. It can't be. Even though I wiped the front and back clean using a different method?
I wipe it slowly and gently with Paper which I had prepared separately. Then, certainly, Wound was attached there. It is a new Wound. It is shiny.
A moment later, a tremendous amount of regret strikes. As usual, I should have sprayed Cream and cleaned it. Even though I've cleaned up to here.
I bought this product to avoid getting Wound and this is what I got. It's half my fault, though.
The misfortune is continuous, and this Panel is not attached to Meter.
It is stated that it is better to wait for a while, but the shape clearly does not fit in the first place. There is no way it will stick forever. In order not to cause misunderstanding, of course, the process as described in the Instruction Manual is followed.
I think that it is strange in a stone, and when I look at the Review of the same product in Amazon in a hurry, User of foreign countries It doesn't stick. I'm telling you. It's too late. Everything is too late.
In other words, I paid two thousand dollars for Garbage.
I'm drooling in front of a Meter with a Wound, a leftover Meter panel, and a bunch of obnoxious CROSSes.
suddenly seeing "CHINA It says.
Again, I was deeply disappointed, but also strangely frustrated by how satisfying it was.
In addition, I found a dent in the Silencer that I hadn't noticed the last time I was standing on it.
My heart will not be healed by a little bit of board gold.
View detail
Fits: Others
Doesn't work for tiger800.
It doesn't work for TIGER.
The Silver ring on the connection part is obtrusive and interferes.
View detail
Fits: HONDA CB300R, HONDA CB125R, HONDA CB250R
CB250R.
I tried to put Antiglare first, but Meter looked blurry, so I put Super clear again.
I wasn't even sure how it worked as Antiglare.
Super clear is so beautiful that you don't feel the existence of film if you put it well.
But, because I failed a little, I used the remaining film after removing this film as a mount for Size:I think I'll try to use Free's smartphone Film with Cut.
View detail
Fits: Others
Easy
I was worried at first whether I could connect it well, but I was able to use it without a problem by inserting it firmly to the back. waterproof is a little uneasy, but the lid is also more solid than I thought, and it seems to be no problem as long as I do not use it in the rain. View detail
Fits: HONDA CBR1000RR-R FIREBLADE
If you are not good at applying Film
First, set Meter to Beauty, and then set Water to Meter and Film.
Mist it.
Use the included spatula to push out the air bubbles from Right to Left. It's very easy to do. I don't think you will fail.
View detail
Perfect fitting, great protection from water and mud splashing around the engine!
I was concerned about the double-sided tape that came with the product, so I used the Scotch vehicle tape I had on hand and installed it on the FFender.
Even if you don't use the supplied Anchor Pin, there is no sign of it coming off.
It's an Exclusive Design and the fit is perfect!
Dramatic reduction of water splashes and mud splashes!
Cleaning the fins of an air-cooled horizontal engine can be troublesome, so this item is a must-have for owners who need to run on wet roads.
View detail
Alright
There is a lot of mud splatter when you use the Fender Eliminator. So I put these on. I posted this about 2 weeks after I put it on and it got rained on during my commute. I also work from home, so I haven't tested it enough, but it's nice.
Installation is very easy. Clean with the included AlcoholSeat
It is glued with Double-sided Tape and left for 12 hours.
I leave it crimped with Shako. After that, I drill the clip of the attachment with M2Drill and melt the reverse side with a lighter to make it difficult to peel off. So far, it has come without a problem. It is convenient if you have the type that does not have a shako in the home center because it is sold for 2~3 hundred yen. The instruction manual is included and it was kind to the beginner.
View detail