Reviews
I think it's good
I bought a used car with unknown mileage and this product from Impression here I installed it with reference to the review Since about a quarter of the Roller before replacement had already been worn out, I replaced it and installed it I think it was good The color also coordinates with other Custom parts and I bought a Red Roller in Red I did View detail
Was it good to purchase?
Attach S Size to KLX 125. In the OEM, the part of Rubber is scraped and the black stain is dirty - - -. After replacement it will not get dirty and it is in good condition. I was glad to exchange it.. View detail
Is good.
I installed it in KLX 125. S Size is a little bigger than NORMAL, but you can attach it.
It is much better than NORMAL. It will be quiet..
View detail
Corocoro
NORMAL did not rotate, it got worn and replaced.
I think that resistance is also decreasing a little by rotating, but I do not feel it in particular.
Color (color) You can also choose, so the Dress - up effect is half the Large - - - ?
View detail
Just fit
Sher rattles are somewhat concerned. Okay ~ Rumor is one piece decrease phenomenon?
Try to remove it, Big! It was rotating pretty.
How to exchange.
Engineer Tsuduaku from day to day, may have been rotating as it attached Grease to the moving section. Individual difference?
First, Glasses on Reverse side (Prevents Nut from tampering as it is from the Reverse side) , The table is a long patterned Wrench (Torque up) , * STAND a cushioning material such as Dustcloth (Described later)
Because I could not insert it to the end at the Bolt, as soon as I got to Screw Mountain tighten together.
The impression is the Brush - Bo effect? ??Surely the sounds that Bearing is running are done. It is not bad.
If the color is Red or Blue, so dirt becomes more conspicuous, so change it to black color.
By the way, winding Dustcloth on Side Stand is because you can give power without hesitation. If you are not nervous, feel free.
View detail
Mounting on KLX 250
I installed it in KLX 250.
With OEM Roller and Black,
I thought that I wanted a color at some point and purchased it.
I can not see much if I install it - - - (;^^)
Because it is just replacing with OEM's Roller,
Installation is very easy.
View detail
Thanks for preparing OEM's Size
OEM Roller of WR250F has decayed, so exchanging, Bearing Smooth movements in internal organs. I'm glad that Color will also be One Point. Although I purchased M and L, it was slightly different. It was attached without problems. View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF450X, HONDA CRF450X, HONDA CRF450R, HONDA CRF450R, HONDA CRF250X, HONDA CRF250X, HONDA CRF250R, HONDA CRF250R, HONDA CR250, HONDA CR125, KAWASAKI KX450F, KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF250X, HONDA CRF450R
Universal Product So it can not be helped
It can not be helped because it is a universal product, but if the attached Color is short it will not rotate to Smooth. Separately, I bought a long color and somehow secured the smooth rotation. Also, the width is shorter than the OEM and a little uneasy remains.
However, except for the above points, this price is acceptable if you enter Bearing at this price.
View detail
DRC Chain roller
Small Chain roller is also an exchange.
OEM is just stabbed in Rubber Color, but since DRC enters Bearing, it is obviously Upgrading, I think movement will improve a bit and I think that it will give you more or less muffling effect, OEM like plastic It was Chica Chi..
View detail
DRC Chain roller
Somewhat the diameter and width are different from OEM, but it will not be a problem
The contents are almost the same as the OEM, OEM was OK, but since the Rubber softens it will be effective.
View detail
Used for YZ250F
Since Roller on the lower side of YZ250F was decreasing, I chose L Size.
Bearing is also solid, rotation also Smooth.
It was cheaper than OEM Product.
View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF450X, HONDA CRF450X, HONDA CRF450R, HONDA CRF450R, HONDA CRF250X, HONDA CRF250X, HONDA CRF250R, HONDA CRF250R, HONDA CR250, HONDA CR125, KAWASAKI KX450F, KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF250X, HONDA CRF450R
Off It is not a car, but ...
Motorcycle with Omniped Chain slider is purchased for avoiding Frame and Swingarm because the number of LINK of Ketsu + Chain has increased, so Chain is rampant.
In SRX, Bolt on the lower side of LeftStep base was in a good feeling position, so it was possible to attach it with Step base with Color interposed.
Off is a product that has not been remembered for a long time due to invasion of mud, but this time it is diverted to On car (?) So I think it would be nice to last long.
View detail
Chain roller self-made
Along with extension of Rear suspension of XL 1200 C SPORTSTER 1200, I made Bracket and attached Chain Tensioner Roller to suppress slack at the lower side of Drive chain.
If there is nothing there is no problem, there is no problem, but if there is, the time lag of the slack of Chain which started running will decrease, the Throttle response will be felt well and the bash crash when throttle is closed will also decrease, so that it will be hard to make a shit is.
View detail
DRC Chain roller
Buy M Size Red for KLX 125.
KLX 125's OEM Roller does not rotate The inevitable Spec. So I exchanged with Chain at the same time.
After exchange it finally w
Since it is with Bearing, the movement is Smooth, Rubber makes it a pla, so it sounds a bit sharp, but it is an unnecessary Level.
I did not have any problems, but my friends seemed to need processing because the finish was bad, so I wonder if there is Rose Tsuki?
View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF450X, HONDA CRF450X, HONDA CRF450R, HONDA CRF450R, HONDA CRF250X, HONDA CRF250X, HONDA CRF250R, HONDA CRF250R, HONDA CR250, HONDA CR125, KAWASAKI KX450F, KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF250X, HONDA CRF450R
It was not a compatible model
Although it was used for DT 200 WR, it was able to install on the upper side, but Shaft size did not match and could not be used on the lower side. Since the upper side can not be used with only the supplied Color, we installed three Washers and installed it.
Bearing does not turn too lightly for internal organs. Yamaha parts may be sufficient with OEM Product because OEM is also cheap.
View detail
Replacement as OEM Product has deteriorated
XR250R (ME06) I exchanged ChainRoller bearing as it died. COSPA is also good and I think that I will purchase this product next time because I can choose Color & Roller size. There is no problem at all View detail
High Universal properties
Because it is a Motorcycle without Chen Roller, I bought it for my own work that prevents Swingarm's interference.
Actually, I used the same item once before, but I ran about 3000 kilometers and crushed it.
However, I feel that my way of installing was bad, rather than saying that the durability of this product is bad.
By saying that by both performance & Cost this product was purchased for the second time.
View detail
Fits: KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF450X, HONDA CRF450X, HONDA CRF450R, HONDA CRF450R, HONDA CRF250X, HONDA CRF250X, HONDA CRF250R, HONDA CRF250R, HONDA CR250, HONDA CR125, KAWASAKI KX450F, KAWASAKI KX450F, KAWASAKI KX250F, KAWASAKI KX250F, KAWASAKI KLX450R, HONDA CRF250X, HONDA CRF450R
Replace from Aprilia RS 125 OEM Product
Aprilia RS 125 OEM Product has worn out and replaced.
M Size is + 1 mm from OEM Product but attached without problems.
When installing, use the attached Color on the outside.
Inside the original Spacer is removed.
OEM Product It is troublesome to take orders so it is helpful to use substitute items.
View detail
KLX125 is a little Large.
So I
NSK (NSK) Stainless Steel MINI Auteua BearingZZ Flange type Model SMF
Insert inside with SMF128ZZ
Use OEM by turning without Flange
Color of inner diameter 8 mm is required.
Washer etc. on the outside of Bearing as well
Devices are designed so that rotation becomes Smooth
Until 11 years the year is 14 / 8
However, since 12 years the outer diameter is 12.
Bolt size is 8 mm.
View detail
other than.
While making a remodeled Motorcycle of Monkey type, Chain is attached to the mounting parts of Rear Sets, and the part gets worn out by hitting it. At first I was Chain for Roller Monkey of GCraft Company, but the vibration was terrible! And moreover, it worn out considerably! It was not bad, but to search for others.
I bought Size of DRCChain roller, besides S Size Large Yeah! I attached the impression that I tried installing well because of Bearing! It is quiet in sound with Rubber! There is no vibration! Is it durable again?
View detail