Reviews
Stable.
[How is it used?
Purchased for navigation when touring
Was the one you received as per Image?
It was fine as per the Image.
Was the installation difficult?
You have to first adjust to the Size of the phone you are using, but it wasn't a particular hassle.
How was your experience with it?
I am satisfied with the product as it does not shake while driving and does not seem to have any risk of falling off.
I use it on an older phone that I can give up if it breaks, drops off, or I forget to remove it and lose it.
The 3-point hold of this product was convenient for a phone with a power button on the Right SideCenter and a charging terminal on the Left Side.
View detail
Fragile Construction, bad quality plastic.
This item looks very promising in the pictures. I really liked the design. In reality It is very weak. It is made of a very weak type of plastic. I have seen cheap phone holders for 7usd that use better material. There are very important parts in this design that should be made of metal, but in this case those are made of thin plastic. From the outside It looks like the body is made of aluminum, but it is just a decorative sheet metal part. If I knew, I would not pay more than 12 usd for this product. On the other hand, the vibration damper doesn't seem to do much. The Handlebar clamp is made of aluminum, but because it is very thin, It looks like it will break if you tighten the screw too much. Don't use this holder on single cylinder bikes, because the damper is not effective enough. Be very careful when installing this product, because It is not made of strong material and it will break If you tighten the screws too much. It looks like It will not last much under the sun either. For 52usd I expected a sturdy well built phone holder. It doesn't look like it was made in japan because of the cheap quality. It is expensive, bulky and flimsy. Next time I will try with SP Connect. View detail
Smartphone Holder Installation
I was able to easily attach my phone to this Holder without blocking the power and volume control buttons, and it holds the phone securely. The only thing that is a little disappointing is that the phone's MainCamera is located in the Center, so it blocks the MainCamera. View detail
stout
I purchased this product to use my phone as a car navigation system. I chose the Rigid type this time because once I put it on, I don't take it off so often.
The product itself is very sturdy and very secure. It is also very adjustable to accommodate large phones. This adjustment is very nice since there are large smartphones these days.
View detail
Overall, I feel like I'm almost there.
I have been using SP CONECTO for about 2 months now.
I wanted to attach it to the Stem for a Simple look, so that made me a little dissatisfied with the usability.
SP CONNECT:SP CONNECTO:MOTO STEM MOUNT (MotoStem Mount)
I am putting it on the imprementation of the Meter, but when I put my phone on the Center, I can't see the Meter.
So by mounting it on the Right side, visibility of the Meter and phone is not a problem! 。 ...So far, so impre...
I have noticed that when I look at my phone on a sunny day, I often can't see it at all because the sunlight reflects off my phone.
Because the phone is mounted on the Right Side rather than the Center, the screen is almost horizontal (the vertical front cannot be raised), so I think there are extra reflections.
Therefore, we placed a Rubber Bush across the front of the angle adjustment portion of the Stem Mount so that it is slightly tilted in the vertical position of the phone.
This is a little better.
Well, I don't use it when I'm running, so I guess I can just stop and touch my phone slowly.
Not to complain, but the length from the Stem to the phone mounting can be adjusted, and the front and rear Quantity:Pair (for Left and Right) I think it would be more visible if it could be tilted to the left or right.
View detail
After all, it is a place where a charging cord is not necessary. 0
I had been using the company's Holder without Qi, and I was satisfied with the Large Change Hold feeling and the vibration prevention, which mitigates the effects of vibration on the phone. After all, detaching and attaching with one hand is very convenient. This time, I replaced it with this one because of the hassle of the charging cable and the fact that it stops charging in the middle of the charging process. Just by eliminating the cord, it is considerably stress-less. I am using it with USB, but it would be better if the cable that takes it from the power supply could be removed. (The hold feeling is as good as ever, but it is sometimes difficult to operate the smartphone screen corner due to the frame, so in that sense, one star is reduced. However, it is an excellent product. View detail
XGrip is great, but Stem's Mount is ….
I installed it on a gsx-r125. Since the Handling Instruction Manual is all in English Version, I installed it while using GoogleLens. The Rubber of the Stem Mount turns and the Screw loosens quickly. It seems that the Stem Mount will not come off while driving.
It might be better to buy only the Stem fixing part, which belongs to the genus Gold from PLOT….
View detail
Instead of RAM MOUNTS
I decided to use RAM MOUNTS for another car model, so I looked into buying another RAM MOUNTS.
The price had gone up quite a bit and I was Biggly. So I bought it instead.
The GSX-S750 originally had a large diameter handlebar, but we were able to accommodate it with a rubber seal.
Release is also a Quantity:Set is easy, fast and reliable and I am satisfied.
Kaedear, you've been coming on strong lately. I have high expectations for the future.
View detail
Dantes easy to use inexpensive smartphone Mount.
I have this on my ZrX1200 DAEG. I have used other Manufacturer's Smartphone Mounts, but I think this one is the easiest to use. It locks by itself when I press the phone against it and the release method is easy to understand, so I even think I will replace it with this one when the other Manufacturer's Phone Mount breaks. I am satisfied with the price and functionality. View detail
It's a reliable product.
Material:I chose this one because I thought Plastic's was a little less trustworthy.
The aluminum arm has a luxurious feel and can be fixed firmly.
No Vibration Absorption Unit, but no problems so far with Android.
It comes with an auxiliary silicon band, and the Instruction Manual says to be sure to use it, but the Package does not mention it. This seems a bit unfair.
Well, even if you don't use it, it looks Large sturdy.
View detail
Properly installed.
Product Name
SP CONNECT SP CONNECT SPCO NECTO Universal Interface
Item Number
34216
Vehicles
MT-09 (2021)
Number of man-hours
About 10 minutes
Required Tools
Scissors, Rubber Band
Why did you choose this product?
The Motorcycle I bought had a SP CONNECT ESPECO NECTO Mount on it, so I thought about replacing the entire new phone mount, but I wanted to get it cheaper, so I went with this one. I also didn't need the phone Cover I have now, so it was just as well.
Was the one you received as per Image?
It was just as shown in the Image, and the Instruction Manual was also included.
Was the installation difficult?
Large sturdy if the mounting position is not mistaken.
How was your experience with it?
I am glad that it was able to be installed securely and still withstand the vibrations of the motorcycle.
[Included Parts:were they on?
Removal Tools and Installation Replacement Parts and Instruction Manual
[Was there anything that disappointed you?
The product could have been cheaper.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
A bit sorry
I tried to install a RAM Mount with this on a 12mm diameter bar.
When I tried to apply it, it was 13mm, so it was loose and turned.
I tried shaving the gap to accommodate 12mm, but no matter how much I tightened it, it still slipped and rotated and could not be fixed.
I tried to put double-sided tape on the Pipe to hold it in place, but the entire Tape kept spinning.
I gave up at this point. I'll think of another use for it; I wish the inside of the Spacer was a soft Material.
View detail
To prevent phone damage
There are many occasions when I use Navigation on my smartphone when I go to an unfamiliar place, but I decided to purchase this product because I wanted to prevent damage to my smartphone to some extent, and I wanted to do so within an easy range. I decided to purchase this product because it is relatively inexpensive and has favorable impressions. The fact that the base and length adjustment arm are made of gold gives me a sense of security, and the easy operation of attaching and detaching the phone makes it convenient to use.
The only thing is that the Parts at the tip of the Arm that holds the phone are Material:Since it is made of plastic, I thought it would be better to have some kind of support to prevent it from falling. With this, in case Material:It seems to me that even if the Plastic part is damaged, it would inhibit the phone from falling to the ground.
I felt that it would be more secure if the holding part of the Arm tip was also made of Gold genus, even if the price was slightly higher.
View detail
Mounted on X-MAX
I purchased this product with the claim of vibration reduction. Easy to install and good design. I haven't had any problems so far with my phone breaking. It is easy to use. View detail
Fits: YAMAHA Tricity155, YAMAHA MT03, YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-25, YAMAHA MT-03 (2015-), SUZUKI GSX-R125, KAWASAKI Z125 PRO
It is a good item
Another motorcycle was a rigid type, but this time we installed this slightly less expensive product. The installation was completed in about 10 minutes and I am able to use it without any problems. I thought it would be better if the angle of the carrying surface could be changed to Up downwards. View detail
RAM Mount
Ram Mount for GSX1300R HAYABUSA.
I bought it because all my friends were wearing this.
I was worried that it would fall off, but it never fell off at all, and I have never had Camera break due to vibration.
… but my friend had a broken iPhone Camera, so I'll leave that to your personal judgment.
I am using my old iPhone XS as Navigation.
View detail
Smartphone Holder
I use an iPhone 12 and it is Exactly very easy to use View detail
I kinda like Gui Mick. (Lol)
It is pricey, but there is something about the giMick that is white in the face.
Well, not only is it good looking, but it is also easy to use.
There is a locking mechanism, but you might not want to trust it completely. To be honest, you never know what might happen.
Dropping a phone is the end of the world. Namu! (σpωp) σ
View detail
Fits: YAMAHA BirdCity, YAMAHA MAJESTYS, YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA MT03, YAMAHA Tricity155
SmartphoneFolder attached to SEROW250
Smartphone Holder is temporarily needed and installed.
The Front was taken out by sand and fell over to the Left once on Asphalt, but the phone did not come off or break and Large was sturdy.
View detail
Freedom from unplugging the charging cord!
[How is it used?
I had been using RamMount as a Smartphone Holder and had no complaints about the body itself, but the only thing that I always found troublesome was connecting the cord for charging.
Since I use my cell phone as a navigation device, the battery drains quickly, so I always have to charge it while riding. Therefore, I have to unplug and plug the cord every time I leave the motorcycle and every time I ride again.
Was the one you received as per Image?
In the picture, each of the parts looked large and bulky, and the image seemed to stand out, but the actual product is a very ordinary Smartphone Holder.
Was the installation difficult?
The act of removing the Cowl and tinkering with the electrical system was too much of a hurdle for an amateur riding specialist, so I asked Timing to install it with me at Motorcycle Shop, where I would install a driver's license.
How was your experience with it?
It is only a small step, but it is much easier now that I don't have to unplug and plug the cord! The charging speed seems to be the same as from the cord.
Manufacturer's description. The Slide arm on the top can be fixed by simply pushing up on the phone, and can be removed by simply pushing up. Smoothly attach and detach the mobile holder with one hand." I have been using two hands because it takes a lot of strength (perhaps men can easily take it on and off with one hand). (Men may be able to easily remove it with one hand.) Since it is held firmly, I am not worried about it falling off while driving.
Vibration absorption is also said to be Standard Equipment (I couldn't really tell when I ran with it), and although I have never been particularly concerned about vibration with the Ninja, I'm relieved to know that it's there.
[Included Parts:were they on?
The screw for attaching the parts connecting the body and the mounting part was not of a common type, but had a special tool.
[Was there anything that disappointed you?
The part of the claw that holds the phone Body is Red color. It may be good for those who choose Red as a color scheme, but it is not my favorite color and I wanted it to be Black. I want to repaint it.
View detail