Reviews
For Torque wrench
Purchased hex bar Bit for use with Torque wrench.
If you have a lot of Bit tools, this one is good for more situations you can handle.
View detail
How effective is it?
I purchased these socks in the hopes that they would help reduce foot fatigue from touring, but I didn't feel that they were very effective. I did not feel the effect of these socks. View detail
Driven Sprocket Replacement
I purchased this to replace a Driven Sprocket, but could not use it because the Nut seemed to lick when a strong load was applied.
I bought another socket (TONE hexagonal) at Home center and replaced it. The price was about the same.
I thought that a hexagonal shape would be more suitable than a dodecagonal shape because of the torque applied, but Webike did not have a deep hexagonal shape, so I had no choice but to purchase one. I used it once and will never use it again.
View detail
For removal of Bolt from Suspension
[How is it used?
YAMAHA XJR400R (07) The Exhaust System Hanger was used to install the Exhaust System Hanger on the Suspension of
The bolt that fixes the suspension of XJR400R is a 10mm hex lobe bit, but a tamper-resistant bolt is used. I used this product to remove it.
Was the one you received as per Image?
It was exactly as shown in the Image. The texture of the product is good and I can use it for a long time.
How was your experience with it?
It is easy to use. It has a luxurious feel.
It is a product that is not usually used, but it is a must-have when performing suspension-related work.
[Points to note]
nothing special
How did it compare to other products?
The same product is available from other manufacturers, but I think SK11's product has the best Cost performance.
View detail
Used to secure Side Back
The Side Back of the Motorcycle was impacted by something while driving.
To prevent the back from falling off in case it comes off.
Used as an apparatus to connect MotorcycleBody and Side Back.
As a consumable, it should be replaced after a few years of use.
Excellent cost performance
View detail
For cleaning complex shapes around the Engine
Engine fins and switches in the Handlebar.
Purchased to clean crevices in complex shapes.
I do this about twice a year, just to clean up all the little details.
Long cotton swabs are used in the gaps between Engine fans, Switches, etc.
It removes dirt and grime from even the most complex shapes.
This is convenient and useful.
View detail
Realizing the need for proper Tool
Maintenance tends to use compact tools, but there is a risk of damaging the bolt if you apply excessive force to loosen the bolt. It is easy to loosen the oil drain bolt. View detail
9.I wanted 5mm.
I use an Impact Driver for APRIO Clutch maintenance, but it only has a 12.7mm 24, and I wanted to use a 9.5mm driver because it was troublesome to replace the Adapter and other parts.
If I use 9.5mm to tighten or loosen 24mm, I may break Adapter or Socket wrench by Overtorque, but I would like to use 12.7mm in that case.
I often use SK11 tools because they are cost-effective.
View detail
Standard products in Eyelet Punch
Purchased to create a hole for Carabiner on Baseball cap to be used when getting off Motorcycle. It expands the range of carrying options.
The product feels solid and usable, and there are no problems. The product comes with an eyelet, so it can be used right away.
It is also reasonably priced, so you can use it in various ways if you have one.
View detail
Convenient but requires skill.
Chamfering tool for Gold parts.
I used it when I made the collar on a lathe to install a CRM50 Wheel on a DT50.
I decided to use it because I had removed it from the Zipper and because I had the tool on hand.
It is quite easy to remove at least a thread chamfer.
However, it is not suitable for Large beveling because the surface rattles depending on the amount of force applied.
Also, for beautiful circle chamfering, it is more recommended to use a large-grit drill, a conical chamfering tool, or a conical file (with abrasive particles electrodeposited) rather than a Chamfer Scraper, because they are cleaner.
In addition, the aforementioned The amount of force." However, there are more appropriate tools for hole chamfering, etc., so it is better to use those tools for clean machining.
View detail
It is not necessary to have it, but it is convenient to have it.
At this price, you won't feel like you're missing out if you have one.
The thicker grips make it easy to hold and apply force, and it is definitely easier to turn than using a 500-yen coin.
View detail
Unfortunately, it did not come off.
[How is it used?
The front coverBolt on the Scooter has taken a licking.
I bought it.
Was the one you received as per Image?
They did a Screw cut that bites firmly into the Plus screw that has been licked.
How was your experience with it?
As a result, the Rusty and sticking Screws were not scared.
[Points to note]
It says to remove it by tapping it with Hammer, but be careful because tapping sometimes changes the direction of rotation.
View detail
Essential Tools
I think it is safe to say that this Tool is a must-have if you are going to tinker with Motorcycle by yourself.
It is a strong ally to loosen Bolt & Nut that are sticking or in places where it is difficult to apply force with ordinary Glasses.
Combining this handlebar with a 6-sided type socket allows for loosening while reducing the risk of tampering in the case of large sizes.
Forcing yourself to work with a Tool that does not fit your purpose or situation will not do you any good.
SK11 is priced much lower than the top-rated BrandTool, but there are no problems with accuracy or strength, and it is easy to purchase.
View detail
To new.
It is reasonably priced and works well for rust removal, removal of bad stains, and polishing.
The one I had purchased before had been used for quite a long time and had become tired, so I was able to purchase a new one.
It is also reasonably priced, which is helpful as a consumable during maintenance.
View detail
Well this
I purchased this product to polish the base of the exhaust pipe (chamber) of my DT50 because the paint had peeled off after years of use and it was rusted and gunky.
It didn't fall off as hard as I thought it would. I think it would have been better to use something like a jetter or TippingHammer to roughen it up a bit and then polish it.
The handle is a little difficult to hold. I think it would be easier to use if the corners around the grip were removed
View detail
Good for fixing when machining or fabricating Parts!
[How is it used?
I bought this for fixing when making parts for out-of-print cars and other parts fabrication and parts machining.
Was the one you received as per Image?
It is heavier than expected, quite sturdy and solidly built with no rattles, etc.
Was the installation difficult?
Bolt holes are provided for mounting on a workbench for easy fixation.
How was your experience with it?
It is very easy to use despite its compact size.
The small Vise can be securely fixed without shaking even when processing grinders, which is dangerous. It also makes it easier to file small parts, which greatly improves work efficiency.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
I have no complaints as it is very easy to use for the price and works beyond my expectations.
▼ I think it is such a useful tool that I wish I had purchased it earlier.
View detail
Considering the price, I am satisfied with Large.
The fact that you can buy so many sockets at this price is enough to make you feel like a big shot in the arm.
The quality is not cheap or poor, and it is usable in its own way.
Since it is not possible to purchase Single Item, we replace frequently used items with more expensive Single Item when they are worn out. (10mm etc.)
View detail
I think the sound is too loud.
It's enough to do a little muscle training? The weight of the machine is about 1,000 pounds.
The operating noise is noisy, perhaps louder than a motorcycle engine running at full speed.
If the electric Tucker is as good, you might as well go for it.
View detail
I purchased this for Tank removal.
The Tank of CB1300 is fixed with Frame and Wire, and this Wire is fixed with Torx screw, so I bought it to remove this Wire.
I don't think I will use it very often, but it would be nice to have.
It also comes with a Holder, which is convenient for putting it away.
The product is from a well-known manufacturer and can be used with confidence.
In general, the product is satisfactory.
View detail
Very effective for cleaning inner axles of Wheel, etc.
Purchased for maintenance of a friend's moped scooter.
It was mainly used to clean the inner axles of the Rear wheel and DrumBrake lever when replacing the Rear Drum brake.
First, apply Cleaner firmly, then add more Cleaner each time while polishing with this product.
The dirt was removed amazingly well.
We applied Grease while using this product as a brush at the end, so I think it has a lot of applicability.
Motorcycle parts are often inaccessible due to the large size of the body, so the large size was very useful this time.
Since it is not an expensive product, it should be disposable.
In that sense, I think it has excellent Cost performance.
One difficulty is the hardness of the brush part, which is made of gold, although this is to be expected due to the performance of the product.
Do not hold the Brush part with your hand when actually using it in your work.
View detail