Reviews
Tanaka Shokai Tanaka Show Kai Chain Tool&CrimpTool set
This is the first time I have purchased a ChainCutter&CrimpTool set. New RKBlackChain replaced 。 The tool is easy to use and a very good product! 。 Please try it outRecommendation. View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Better than expected.
Used in GORILLA.
It is Chromium Plated on Steel, which is better looking than the pure Black of other Manufactures, and the accuracy does not seem to be bad.
View detail
It's really bad.
It cannot be installed on the normal head. It hits the valve and hits the top of the head, causing the piston to stop moving up. I couldn't start the engine because of this part, so I left it at the motorcycle center for over a month. Paying for the motorcycle center is too stressful. Never buy it. It doesn't make sense to sell products that are not made properly on Webike. I'm very disappointed, I'm too stressed out, and I'm thinking of scrapping my bike. View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
Magnet strong! Safe because it is made of steel
Material:The colorful aluminum drain bolt has a nice parenthesis look, but I decided to go with this one because I thought steel would be safer for tightening the bolt firmly.
Magnet is very strong and high quality.
Is the price a little high? I'm not sure.
Since the car body is old, I am going to ride on Large with particular attention to these small parts.
equipped (with)
2002 AA01 CUB STANDARD50
View detail
Fits: HONDA DAXetc., Others , HONDA MONKEY
Axle Shaft insertion is by far the easiest
I used it to remove and install 1200CX Front wheel.
I had considered a very inexpensive STANDJACK similar to this product, but many other reviewers had criticized it for its lack of rigidity, etc., so I decided to purchase it from the trusted Webig.
I have been using Pantograph jacks, so the stability of the car body during jack-up is completely different, and I can start work without worrying about work accidents.
It should be noted that I can now easily insert the Axle Shaft of the front wheel, which I had difficulty with before.
I wish I had bought it earlier because it can be used not only for DoubleCradleFrame but also for Twin spar frame cars.
View detail
Fits: HONDA XR100 Motard, HONDA dachshund, HONDA Dax 70, HONDA Ape 50, HONDA dachshund, HONDA Ape 100, HONDA Dax 70, HONDA Ape Type D, HONDA Mighty Ducks (ST90), HONDA Ape 100 Type D, HONDA Ape 50, HONDA dachshund, HONDA Ape 100, HONDA Dax 70, HONDA Ape Type D, HONDA Mighty Ducks (ST90), HONDA Ape 100 Type D
NTN Bearing
About quality and texture NTN always has the quality to trust and buy About the feeling of use It's not used yet. I had to buy two, but I only bought one Products to buy together rubber hammer Difficulty of installation difficult, hard Cost performance and comparison with other products It is the cheapest and has a reliable quality About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I did two in quantity, but I couldn't check the quantity because I was purchasing other products first I should buy it again when I buy other products Since it is an old bike that is 10 years old, there are many things to be done, so it is the most important part of it, and the quality of it is also reliable View detail
Unique Features
It has a Binder.
It can be used to hold small objects such as removed gloves.
Very convenient
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Lowest quality
(Note:WeBig has been good to us. It's about the item itself.
Distance Collar is lowered by its own weight and Axle does not enter from the side.
Through Mr. WeBig. Funny, isn't it?" I said.
"It's the part that keeps Bearing from getting inside, so it's not a
It is slightly movable before installation 。 "
He was kind enough to tell us about the body structure.
（The OEM has a flange that is press-fitted into the pipe so that it fits almost in the center while still wiggling around. However, this one does not have a flange and is just a Pipe. Of course, there are some models that have only a pipe, but in those cases, the inner diameter of the hub is narrower so that there is not much gap from the center even though it is a pipe shape.
When you install it on the car body, of course it is in this direction (the bottom side of the image is the ground), so I guess it means that you should insert it after putting out the Center by inserting a Driver from the opposite side….
The most surprising thing is this. It's Spec. This is Tanaka Shokai, which says
You have to do a lot of them to know if it's too Gap (too Large). （I'm sure you can't tell that this is too Gap (too Large to play with) unless you play with a few units.
I wonder if they would be able to push through with that (Spec. ), I guess I'll be able to push through with that (Spec.
View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
Strong magnetic force
Material:We decided to use steel because it is better than Aluminum.
Large sturdy even when tightened as much as possible, and the magnetic force is strong and effective.
Is the price like this?
View detail
Fits: HONDA Ape Type D, HONDA Ape 100, HONDA Ape 100 Type D, HONDA Ape 50, HONDA Ape Type D, HONDA Ape 100, HONDA Ape 100 Type D, HONDA Ape 50
Difficult to install if the product is wide enough
I could not install it due to the width of the product.
I cracked it.
View detail
Touch of Lever has improved.
The NORMAL fork and wheel may be a little too much, but it is much easier to maneuver and touch.
Also, the drum-like part that goes into the lever on the wheel side was not thick enough to fit, so I had to use the previous part to make it fit.
I think I ordered what I saw because it was my first time using the site and I wanted to be sure to check it carefully next time.
View detail
fashion-conscious
Appearance oriented, self-satisfied, cosmetic? View detail
Easy to use
Cheap, but easy to use, and made it easy to change the Exhaust System. View detail
Fits: HONDA dachshund, HONDA monkey, HONDA For turnip horizontal engine, HONDA Shari, for horizontal engines, HONDA For turnip horizontal engine, HONDA Shari, for horizontal engines
DAX Kick pedalF
It was rusty rusty so I replaced it with this new Pedal. The product was solid and the plating was very smooth. I am very pleased with the Polished look of the feet as if they were brand new. View detail
Fits: HONDA APE, HONDA CUB, HONDA MONKEY, HONDA MONKEY
It was damaged after 8 months of use at 4000 km Meter.
I purchased it because it was less expensive than OEM Parts, and installed it. However, the gold material at the contact point with Valve melted, and I could not use it after 8 months. The cause is unknown, so I will purchase again. View detail
PetitCustom
Quality is high, like Maker Option. It would have been better if there was an instruction manual. View detail
Fits: HONDA MONKEY, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Three stars because I don't know the OEM.
I bought a used MONKEY, can't say for sure since I don't know the OEM shape of the color, but I thought it was well made. View detail
Fits: HONDA ST90 (ST90), HONDA CHALY 70, HONDA DAX70, HONDA CUB, HONDA CHALY 50, HONDA DAX, HONDA GORILLA, HONDA MONKEY
For Wiring lock.
I bought it because I needed a wiring lock for my Circuit run and it's a great value with Washer! View detail
Fits: HONDA MONKEY, HONDA GORILLA
Large exhaust pipe
A cheap and good looking Chinese Exhaust System.
Silencer is almost a straight tube and a blast!
Exhaust System, I bought it because the exhaust pipe installation part is about 50mm!
I was wondering if the Silencer I have on hand would stick …
The slot had some rattling, but installation was OK.
Satisfied with the sound and the calmness of the sound.
Silencer from the original was a bit Mischief
View detail
Fits: HONDA Fits to MONKEY(except FI) GORILLA etc. Horizontal TypeEngine., HONDA Can be installed on Monkey gorilla etc. Horizontal TypeEngine
Used for SUPER CUBC125
I bought it because it is a little short in NORMAL and the body of the car leans a lot.
Side stands switch is not included.
Connector was removed and directly connected.
Attached Bracket is not used
Then, just pump it in, adjust the adjuster to the desired height, and you're done!
Steel, but with Side Stand with Adjuster that can be used with C125.
It is probably the cheapest.
View detail