Reviews
KITACO suspension tool for the Honda MSX/Monkey
These KITACO Fork Thrust Adjustment Gauge Set are extremely useful in assisting you on setting the exact same height on both fork legs. They have 8 different height settings and are made of stainless steel which means they wont rust. Only improvement is that they could come with a ring to attach the two together, but you can easily add one. Overall it's a quality little tool from Kitaco! View detail
Fits: HONDA CT125CT110 HUNTER CUB, HONDA CT125CT110 HUNTER CUB
I can now drive like I've drawn a clean line both Curve and straight ahead.
While curving Curve, it often went in a direction I didn't expect.
Curve on a rough road surface is a real thrill.
After the installation, this was no longer the case, and the car was able to turn in the desired direction as if a clean line had been drawn.
Straight line driving has also improved.
It also reduces Handlebar being taken out on rough roads.
Installation is a snap if you have the right tools.
It's pricey but well worth it and I'm happy with the Large change.
I am rather upset with Honda for not designing with this rigidity from the beginning.
View detail
Can be raised or lowered freely
I had previously raised the ride height of my 25R with BEET's SportsLINK, but I couldn't stand the gold or silver-colored parts that stood out, so I looked for a product that was less conspicuous and more functional.
Installation is easy if you have a Rear Stand and Jack. However, it is difficult to adjust the plate under the weight of the car because of the narrow space, and it is difficult to turn the plate with Spanner, so it would be easier to turn the plate with Jacketc. There is an adjustment allowance of 2cm up and down, so considering the time and effort required to replace the plate, I think this is a good product.
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE
Design is good!
Lowdown type was selected for better footing.
MORIWAKI is a good parenthesis because it also has an auxiliary bolt!
I am satisfied with it with no regrets.
Parenthesis was further improved by using Titanium for Bolt.
View detail
Fits: KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI D tracker, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250, KAWASAKI KLX250ES, KAWASAKI KLX250ES
Quite effective ??
It's a lot lowerdown and has better footing:??
The movement of the suspension is as good as ever.
View detail
Fits: HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEEDVLX (STEED), HONDA STEEDVLX (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED), HONDA STEED (STEED)
Front fork
I would like to buy it again next time because of its good quality and cost performance.
Installation was no problem.
Not sure about durability yet.
View detail
Replacement from another company's Rear suspension
I think the Level is satisfactory from city driving to touring in terms of quality, control performance, and ride comfort.
I weigh 65kg, I set the Initial setting slightly higher, and the damping force was set to the default setting. [2 The ride quality and maneuverability were Mild and good in the speed range of city driving and touring. When driving on highways, the damping force 3] I am thinking that it would be good in
View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB, HONDA LITTLE CUB
Rear shock with good cost performance
[How is it used?
Bore up the LITTLE CUB and it became faster, but it bounced around on the fluffy Normal suspension due to road surface gaps, etc. and could not keep pace, so I replaced it.
We chose this product when we looked for something that did not change in appearance from OEMNORMAL to LARGE and was not too expensive.
Was the one you received as per Image?
I like the thinness of the OEMRear suspension and the large difference!
Plating and paint texture also felt overpriced.
Was the installation difficult?
Very Kan Tan. just replace one side at a time with OEMRear suspension.
The Instruction Manual says that applying Grease to the vibrating parts will make the movement smoother, so it is recommended to prepare it beforehand.
How was your experience with it?
Quantity:I did not expect much since it was cheap, about 10,000 yen for 2pcs, but I found it to be more than I expected.
In the past, the fluffy OEMRear suspension was bothersome when picking up road surface gapping, but this product absorbs the shock so smoothly that the rider can maintain his pace.
[Others]
The Cap Nut and Washer at the Rear suspension attachment point tend to be rusted, so it may be a good idea to have a new OEM one.
We also want to make sure that the Overtorque is not too tight to prevent movement.
View detail
Fits: YAMAHA SR250, SUZUKI 250SB, HONDA 250T LACustom, HONDA AX-1, HONDA CL135, HONDA CL350, HONDA CL72, HONDA CL77, HONDA CM250T, HONDA CM400T, HONDA CRM250AR, HONDA CRM250R, HONDA FTR223D, HONDA FTR250, HONDA GB250 CLUBMAN, HONDA GB400TT, HONDA GB500TT, HONDA MT250ELSINORE, HONDA MTX125R, HONDA MTX200R
Does not fit the KL250 Sherpa.
The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.
KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.
If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.
Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!
I bought it + even processed it so I'll be using it for a while lol.
View detail
Wife, Large joy
I bought it for my wife, who is in the early 150cm height range, because she had bought an SV650 but was concerned about her footing.
The result is a wife Large joy.
In NORMAL, I was supporting it with the base of one thumb,
When this Link Rod is inserted, the base of both thumbs will be grounded, and one foot will be sticky.
I am 177cm and I already have sticky sticky feet, stickier than my AXIS-Z that I use for commuting.
Write down the installation.
I assume you are familiar with maintenance if you are trying to do it yourself, but I hope this will be helpful to someone else.
First, you need an environment where you can hang Jack or Motorcycle.
Rear stand alone is not acceptable (since the LINK cannot be removed …).
Jacks are unstable, so it is safer to hang them if there is an environment in which they can be hung.
Also, the Exhaust System has to be removed before we can work on it,
If you do not want to use Gasket all over again, please buy a new Gasket.
14181-22D01 1pc.
14771-32E10 3 pcs.
When removing the Exhaust System, remove in the following order:Silencer→ front exhaust pipe→ O2Sensor&rarr attached to the middle exhaust pipe; middle exhaust pipe.
When you put it on, it is in reverse order.
Gasket stuck in the exhaust pipe can be pulled out with a radipen.
Please pull out the chisel with your spirit.
It seems to be the correct way to loosen the O2Sensor after raising the Fuel Tank and removing the Coupler, but I was too lazy to remove it as it was.
It was completed successfully without disconnection, but you are on your own there….
Once the Exhaust System is removed, all that remains is to replace the Link Rod.
If the Bolt of the LINK interferes with the base of the Side Stand and cannot be removed, it can be removed by lifting the Swing Arm upward.
I have not tinkered with the Fork protrusion mentioned by others, as I did not feel any particular discomfort with it as is.
It is my wife's Motorcycle and I will respond when she tells me.
I got a good deal.
If you want to improve your footing, I recommend it.
View detail
Fits: HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA Benly CD90, HONDA Super Cub 90, HONDA Super Cub 50, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
I bought it just for the color.
I won't know for sure until I ride it for a while, but I bought it just for the color, so I am not particular about its performance. View detail
Fits: HONDA CT125, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CROSS CUB, HONDA SUPER CUB110 PRO, HONDA SUPER CUB 50 PRO, HONDA CT125
Shock absorber with limited CROSS CUB50cc compatibility
I was looking for Shock absorber due to OEM fluff, but only Mukawa and Endurance had it as 50cc compatible by Manufacturer.
The damping force can be adjusted to 5 levels, and although I ran the car in the softest state, it felt much stiffer and more firmly planted than the OEM.
Red Nut in the picture is SP Mukawa Rear shock mountNut8 hole Red 06-06-0020
View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Cool
It has a more luxurious appearance.
I don't know about performance because I haven't run it that much yet.
View detail
Fits: KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZZR1400, KAWASAKI ZRX1200 DAEG, KAWASAKI NINJA ZX-14R
The quality of the product is perfect. I appreciate that I can adjust it quickly without using any tools.
That was a good purchase
I appreciate the ability to quickly adjust without using tools.
No complaints about the texture.
View detail
Lowdown
The rear suspension is based on XJR1200 OHLINS, so the ride height was raised and the footing was not good, so this suspension was used.
The car models are completely different, so you are on your own for everything.
View detail
Mounted on W800
Although I have only traveled 2 to 300 km after replacing the tires, I feel that the lack of stability on the Corner, the feeling of being pushed up from the road surface, and the sense of instability felt when driving over longitudinal grooves cut into the road surface, which I felt when using the Normal tires, have been resolved considerably, and I can install them without feeling uncomfortable in appearance.
I think it will be easier to drive more in the future if I can find the best position by adjusting the Pre-road while driving a little more.
Then, if you don't have a Torque wrench, I would recommend putting a Marker in the Bolt/Nut with Magicetc. after installation.
View detail
Fits: HONDA FTR, HONDA FTR, HONDA CB900, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA FTR, HONDA CBR400R Limited Edition, HONDA CBR400R, HONDA CBR250RR (ABS), HONDA CBR250R <ABS>., HONDA CBR250R <ABS>., HONDA CBR250RR, HONDA FTR, HONDA CBR250RR
OEM Product Quality NTB of the same etc.
NTB has a proven track record in automotive parts.
The quality is the same as OEM parts, but the price is low and Wallet-friendly.
No problems with installation.
View detail
Fits: HONDA CROSS CUB, HONDA CROSS CUB50, HONDA CT125, HONDA CROSSCUB110, HONDA CT125
improve one's footing
Footing is slightly better.
This makes the Side Stand longer, or the Motorcycle less inclined and unstable, and the Center Stand harder to apply.
Ride quality is better than OEM.
Now we'll see how durable it is
View detail
It looks good!
NC42Rear suspension was leaking Oil and I couldn't afford OEM because it was too expensive.
The item received is clean with some SmallWound! 。
Installation was not possible because the Bolt under the Right Side interfered with the Exhaust System to remove the OEM! Others were completed Smoothly. The upper part of the Shock was not easy to install, so I applied a little Chain oil as a reference to others and it went in. Also, one of the lower side had to be tapped a little to fit the holes in the mounting position. Also, it was impossible to mount the pon, so I had to extend the overall length by about 8mm to complete the installation.
The ride is not bad, but it feels soft, so I will adjust it. I don't know about durability, but there seems to be no oil leakage and no initial defects.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY
Daytona rear cushion fit Dax50
Daytona rear cushion fit the Honda Dax50 perfect with little modification to top mounting hole. Spring is firm for two riders and ride height is beautiful. View detail