Reviews
Fits: KAWASAKI ZRX1200R, HONDA CB400SF, KAWASAKI ZRX1200S, YAMAHA XJR1300, KAWASAKI ZRX1100, KAWASAKI ZrX1200ZrX1200 DAEG, HONDA CB1300 SF, YAMAHA XJR400, YAMAHA XJR1200, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF
Functional and dress-up
I installed it on my ZrX1200DAEG.
I bought this one to match the color of Anodized with Bar End.
The rigidity is good, and the fact that the NORMAL Wiring could be installed without modification is highly appreciated.
The handlebar is higher and closer to the front, so I feel less tired when touring. It is also easier to handle.
After two years of use, the Anodized remained clean and the Handlebar did not wobble.
View detail
For Dress-up
It is quite bright. Installation requires removal of the tail cowl, but it is not that difficult, so the difficulty level is not high.
The shape is the same as OEM, so Clearanceetc. had no problem.
View detail
MITSUBA Dora Recording Essentials
The REMOTE CONTROLLER installation of the MITSUBA DRA RECORDER is the only choice, and the Fit feeling is unquestionable, but the price is high. View detail
too big a hole
The hole drilled for the Switch box is a stupid hole and the Throttle moves back and forth.
I purchased the Plating type.
I have nothing but regret.
View detail
Fits: KAWASAKI Ninja250, SUZUKI GSX250R, KAWASAKI Z900RS CAFE, KAWASAKI Ninja400, KAWASAKI Z900RS
For NINJA400/250
KAWASAKI NINJA400/250 has the boss of Swing Arm deep, so it is necessary to stop the Rear stands hook. TAGUCHI MFG. (TaGu) I will include a photo of the :109001 Stand Hook in use. View detail
Satisfied. The best.
I had a hard time deciding between the Posh 71 series and the SUPER BIKE, but the 71 was too small and I am too old, so the SUPER BIKE, which is large, was the right choice. I am satisfied with the large size and the presence of the bike after installation. View detail
Fits: HONDA MSX125 (GROM), HONDA MSX125 (GROM)
Looks good, works more efficiently ??
The OEMAdjuster was not very efficient because it gapped or floated immediately when adjusting the chain, but this product is very good because it does not gap because it is hooked to the inside of the swing arm with a Snap!
I thought it was cool because the Adjuster is Gold, even when viewed from the rear, so it clearly stands out!
View detail
Self-sufficient Bar End!
I replaced the Handlebar on my Z125pro when I replaced the OEM Handlebar with a HURRICANE Condor Handle! I bought the Red one, of course, because my car has Red wheels! It is inexpensive, simple and easy to install, so it is a recommendation. View detail
Fits: SUZUKI GSR250, SUZUKI GSR400, SUZUKI GSX1400, SUZUKI GLADIUS650400, SUZUKI GSX-S1000F, SUZUKI SV650, SUZUKI V-STROAM250, SUZUKI V-STROAM650XT, SUZUKI V-STROAM650, SUZUKI V-STROAM1050DE, SUZUKI V-STROAM1050XT, SUZUKI V-STROAM1050, SUZUKI GSX-S1000GT, SUZUKI GSX250R, SUZUKI BURGMAN400, SUZUKI V-STROAM, SUZUKI GSX-S1000S, SUZUKI GSX-S1000
Purchased for ja59
I bought this to install on my JA59, but the OEM Handlebar could not be installed.
I was going to replace the OEM Bar End with a shorter Handlebar width, but this time I got a disappointing result!
However, I am satisfied with the quality of the product and will keep it in stock until I install it on another motorcycle.
View detail
Combined with Rear Blinker BracketPlate
The PoshRear Blinker BracketPlate is used in combination with the PoshRear Blinker BracketPlate, and the blinker appears right next to the license plate, so the blinker can be relocated without being noticeable and with good visibility from the rear for directional guidance. View detail
Fits: HONDA FORZA, HONDA CB400SB, HONDA CB400SF, HONDA CB650F, HONDA CBR1000RR, HONDA CBR650F, HONDA NC700S, HONDA NC750S, HONDA NM-4, HONDA PCX125, HONDA PCX125, HONDA PCX150, HONDA PCX150, SUZUKI GSR750, SUZUKI GSX1300R, SUZUKI GSX1400, HONDA FORZA, HONDA GROM, HONDA HORNET600, HONDA HORNET900
Design is good, beautiful Blue.
I like the very beautiful Blue and the Design is cool. View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
I don't know the effect yet, but I expect it in the future.
The OEM had a RubberDamper and was unhappy with the wobble, so it was replaced.
We chose the color Matte Black based on the shape and size similar to OEM, and it was almost exactly as shown in the Image.
SUS304 (A2-70) Includes M8 x 45mm bolt; Screw protrusion 10mm; OEMWeight screw protrusion 12mm.
The length of the female Screw is about 10mm, although it was not measured accurately.
Bolt material is the same as OEM SCM435 (10.9T) Change to M8 x50mm, Screw lock (LOCTITE243) The reason for replacing the bolt was to make the bolt less noticeable. (Surface treatment:Trivalent ChromateBlack)
After a short ride, I could not feel any difference from the OEM. However, on a long distance, you might be able to see the difference.
It may be an individual difference, but in my vehicle, Quantity:Pair (for Left and Right) There was no interference between Grip and Weight.
Gap between Right SideGrip and Weight:1.5 to 2.5mm
Gap between Left SideGrip and Weight:2.5mm
Actual value
OEM (excluding Bolt)
weight:243 g/Individual
full length:46.5mm
Ultra heavy bar end (Inner + Outer, excluding Bolt)
weight:278g/Pieces OEM + 35 g
full length:49.7mm OEM + 3.2mm
View detail
Fits: KAWASAKI NINJA250R, KAWASAKI NINJA400
Ninja 400 with '23 MODEL
Installed on Ninja400/23 MODEL
The reason I replaced it was because with OEM, it was a hassle to be aware of every hand position when I held it back to turn it.
The scene used is Circuit.
I did it myself because of the high labor cost of working with Naps.
The Cowl and Tank were removed, Handlebar peripheral parts were removed, Accelerator Wire was replaced, etc., etc., etc., etc. The work was large and strange.
If you don't have the knowledge, you should never touch it yourself.
Please ask Motorcycle shop honestly.
The key impresion is that it is very good.
It is useful because it can be turned off firmly.
As a demerit, Axel is heavy.
Your hands will get tired if you are not used to it.
Drooping will also increase.
In SCENE that uses low speeds, such as traffic jams, be careful because if you accidentally turn it, it will be Large strange.
View detail
Replaced with Clutch mesh hose
Used when replacing clutch mesh hose View detail
If you use the Blinker as an LED ….
[How is it used?
I had purchased and used DAYTONA's Blinker relay,
When Blinker is replaced with LED bulbs, abnormal lighting and blinking occurs.
I made a mistake in selecting the parts. So I bought a new one!
Was the one you received as per Image?
Yes, it was almost the same size as the OEM.
Was the installation difficult?
Just replace with OEM.
Replace Connector,
Rubber mount ported from OEM
Quantity on the vehicle body:Set is all you have to do.
How was your experience with it?
No particular problems.
[Included Parts:were they on?
An accompanying Instruction Manual is included.
[Was there anything that disappointed you?
There are no particular inconveniences.
View detail
CUB in Blowby!
CUB I put the Oil catch on the end of the Hose. The price and the quality of the product are very good. View detail
Fits: BMW S1000XR, HONDA CBR1000RR, KAWASAKI ZX-10R, KAWASAKI ZX-25R, SUZUKI GSX-S1000F, SUZUKI GSX-S1000S KATANA, SUZUKI GSX250R, SUZUKI GSX1300GSX1300R HAYABUSA, BMW S1000R, BMW S1000RR, KAWASAKI Ninja250, KAWASAKI Ninja400, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Good sense of unity!
I purchased this for my Roller stand.
The color is the same as the color of the original.
View detail
For mounting of cargo hooks
I used it to attach the Loading Hook for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used a loading hook M8 with the same posh face as the colored Spool and a Stainless bolt M8x120mm without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail
License Plate Protection
I purchased this to protect my License Plate and it fits my License Plate perfectly without any size problem. View detail
Loading Hook
A Loading Hook has been added for easy use of the Net to supplement the capacity of the Small TypeTank Bag. On the back side, a Loop is threaded through the Club bar.
I used the same Posh face colored Spool M8x30mm and Stainless bolt M8x120mm as the Loading Hook without any modification. I think a M8 x 25mm colored spool or a 1cm short Loading Hook would have been fine. However, in the case of the Short Hook, the inner diameter is too large to interfere with the Club bar, and a thin Hook made of gold might be better suited for this purpose.
View detail