Reviews
Fits: SUZUKI GSX750S KATANA, SUZUKI GSX1100S KATANA
Shift rod rust free.
NORMAL steel ROD rusts and looks bad, so Material:I replaced it with this ROD in Stainless Steel, and I could feel the Shift touch getting better. View detail
Fits: SUZUKI GSX1100S, SUZUKI GSX400S, SUZUKI GSX750S, SUZUKI GSX1100S, SUZUKI GSX400S, SUZUKI GSX750S
Replacement is recommended at the time of MeterOverhaul.
KATANA is a fine old car. After many years of driving, the UV rays will cause the needles of the meter to warp, and at worst, the vibration of the car body will break the needles. Before this happens, we recommend replacing the needle with an overhaul of the meter. View detail
Fits: SUZUKI GSX750S, SUZUKI GSX1000S, SUZUKI GSX1100S, SUZUKI GSX1000S, SUZUKI GSX1100S
Rubber plate wheel but exclusive product
It looks like a circle of Rubber plates, but it is an exclusive product that cannot be found anywhere else. View detail
Fits: SUZUKI GSX750S, SUZUKI GSX1000S, SUZUKI GSX1100S, SUZUKI GSX1000S, SUZUKI GSX1100S
This is good stuff.
It has been 40 years since the initial model of GSX1100S.750SKATANA, and 22 years since the final model. Until now, when the rubber on the tank cap was damaged, the entire tank cap had to be replaced, but by replacing the rubber with this product, water can be prevented from entering the tank when washing the car and rust can be prevented from occurring inside the tank. View detail
UNICORN reinforced engine brackets + frame mount set for 1981 GSX1100E
i'm doing a full rebuild, restoration and customisation on my 1981 GSX1100E and this UNICORN engine bracket + frame mounting set is a must have in the rebuild. I will be putting in a lot of performance parts and upgrades for the bike and will be bracing the frame and chassis. This engine brackets and mounting will further enhance the rigidity of the bike so that it will perform and handles better! very quality product and well built. View detail
This is a replacement part for removal and installation.
It's a replacement part when it's removed, so I wish it was a little cheaper.
There seems to be no leaks so far, and the quality is as good as it gets.
View detail
Fits: SUZUKI GSX750S, SUZUKI GSX1100S, SUZUKI GSX1000S
it's beautiful
The OEM is a very large STAND, so it's quite refreshing and beautiful to look at in comparison, and of course the fit is great when stored. (I used to be exposed from a hell of a lot of footpegs) 。
I wanted to use the same stainless steel for the Bolt and Nut, so I got them myself. (M10 P1.25) Why did I buy it on Net?
View detail
Fits: SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1200 s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1200 s katana [katana].
Parenthesis is good.
The texture is very nice and it looks great. I'm very happy with it. I'm satisfied with it. View detail
Fits: SUZUKI gsx1100s katana (sword), SUZUKI gsx1100s katana (sword)
I'm happy with it
The quality of the Oil is excellent, and the life of the Oil has been extended because of the good quality. View detail
Fits: SUZUKI GSX750S, SUZUKI GSX1100S, SUZUKI GSX400S
high price
Expensive.
I thought about replacing it with something along the lines of Maintenance, but it was more expensive than I thought.
Even the OEM was an Assembly, so replacing the Glass was replacing the Meter, but it's good to know that it's partially replaceable.
Also, the Glass was a little dirty. It had what looked like Water Spots on the car.
I thought about returning it, but due to the work involved, I polished it myself and used a thinner Spot.
I couldn't get Spot to disappear perfectly.
It's a shame about a lot of things.
View detail
Fits: SUZUKI GSX1100S, SUZUKI GSX750 1, SUZUKI GSX750 2, SUZUKI GSX1100S, SUZUKI GSX750 1, SUZUKI GSX750 2
ThankfulParts
Was the one you received as per Image?
Expected
Was the installation difficult?
it's simple
How was your experience with it?
Good texture and will last a long time.
[Was there anything that disappointed you?
The price is a little high.
In any case, I am very grateful for this as KATANA`s OEMParts are out of stock.
View detail
![UNICORN JAPAN [Helmet Sticker]](https://img.webike-cdn.net/catalogue/12312/00002s_TS.jpg)
Speaking of KATANA, Unicorn?
This is a Sticker that you can put only normal text. View detail
Fits: SUZUKI GSX-S1000S KATANA, SUZUKI GSX-S1000
I didn't like the way the OEMSide Stand was made.
I didn't like the way the OEM Side Stand was made, and I wondered if there were any Side Stands for other brand products, so I looked for one from Unicorn Japan. (Famous for Parts for KATANA and COMP-Reated Machine) Material as Parts for New ModelKATANA:Stainless SteelSide Stand was released, because it can be used for GSX-S1000 which became the base of New ModelKATANA.
The Stainless Steel Side Stand itself is very accurate and has a beautiful finish that I am very happy with. I'm glad I bought it because it's something I use every time I ride and it's a part I see.
Since the tip part is not so wide as OEM, you may need to put something on the floor or use extension depending on where you park.
View detail
Fits: SUZUKI BANDIT1200 [Bandit] S (GV79), SUZUKI BANDIT1200 [Bandit] S (GV77), SUZUKI GS1200SS, SUZUKI BANDIT1200 [Bandit] S (GV79), SUZUKI BANDIT1200 [Bandit] S (GV77), SUZUKI GS1200SS
It's easy.
Installed on BANDIT1200s gv77A
The actual size was more compact than I expected (about one size larger than TirolChocolate) and it was not difficult to install. The ignition timing is set to the regulation because of the exhaust gas regulation. After reading the reviews from other people, I was skeptical and installed this product and the low rpm sluggishness disappeared and the Large Motorcycle feel came out. The price is more than enough to make a difference.
View detail
Fits: SUZUKI GSX1100S KATANA, SUZUKI gsx1100s katana [katana]., SUZUKI gsx1100s katana [katana].
Order, please.
I haven't received it so I can't give my thoughts on it. View detail
Fits: SUZUKI GSX1000S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX1100S KATANA, SUZUKI GSX750S KATANA, SUZUKI GSX750S KATANA, SUZUKI gsx1100s katana [katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI GSX1000S KATANA [Katana].
RAYBRIGMulti-reflector
[How is it used?
It's for KATANA, but it's for the OEMHeadlight frame of gpz.
If you install it, it is the same.
RayBrick doesn't go to the trouble of inefficiently developing and manufacturing something that's model specific.
The Headlight itself can be attached to anything if you want to, although there are several pattern types.
For use with OEMCowl, mounted on OEMLife frame.
As expected, my face became clear and beautiful.
Light is also bright and clearly illuminated.
It is not only a function, but also an appearance component that determines the face of the product, so it is a custom component with very good cost performance.
Be careful of Spec. such as FOR JAPAN MODEL outside Japan.
Was the one you received as per Image?
Yes
Was the installation difficult?
It takes a lot of work to remove the Inner cowl.
How was your experience with it?
Expected
[Included Parts:were they on?
minimum
[Was there anything that disappointed you?
None
View detail
Gasket exchange of 750KATANA
I started to worry about the oil leak from the cylinder head cover, so I installed this
I replaced the Gasket with an OEM Product, but I think this one is more durable.
I chose it because I thought it would be a good fit. I have no problems with the installation and the position and shape of the Bolt.
It fits well and there are no problems. It's reasonably bouncy and very easy to work with.
If you do the basic things like removing old gaskets, using oil stones, etc., anyone can do it.
I think you can. I didn't put liquid Gas on it, but there is no oozing or leaking.
View detail
Fits: SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1200 s katana [katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1200 s katana [katana]., SUZUKI GSX750S KATANA [Katana].
Titaniumium coat screen to prevent Wound.
BlackTitanium coat screen. I made the cover by hand with Micro fleece to prevent the screen from wound. I think this is necessary because I frequently take off and put on the cover.
And the shade of the Screen you see outdoors. It is a deep shade of blue with purple. It is a high quality Screen that is not cheap.
View detail
Fits: SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1200 s katana [katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1200 s katana [katana]., SUZUKI GSX750S KATANA [Katana].
It is Titaniumium coat screen as per Image.
It's been a while since Screen (Meter visor) I replaced the screen. Although I have used Titaniumium coat screen of Mr. UNICORN for a long time as a favorite from before, the state of coating became terrible as expected, and it came to spoil the beauty and became exchange. Because my KATANA uses dark blue as a main color, a single color Smoke Screen is not suitable. After all, I chose Titaniumium coating as well as Shield. This BlackTitaniumium coating is Semi-smokeBase with Purple coloration. The article was wrapped in the soft paper which wraps the doll, and it arrived in the Cushion of the bag form. This area, the polite work of President Ikeda is made to feel. The Screen is attached to the Bracket with the included Cushion and Washer. At this time, if you do the installation work in the state that is wrapped in paper, I think it will become the wound prevention. Finally, the end of the year. I'm looking forward to seeing the new Screen. View detail
Fits: SUZUKI GSX750S KATANA [Katana]., SUZUKI GSX750S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana]., SUZUKI gsx1100s katana [katana]., SUZUKI GSX1000S KATANA [Katana].
Small for the price.
It's incredibly thin.
I'm afraid I'm going to cut my hand off at Edge.
I black-painted the back side of the camera so it would show through.
The mounting part is also made of LePera, so you need to balance it while tightening it.
The mountings are likely to crack easily with the slightest force applied.
I decided on this one for the Kobe Unicorn stuff, but it didn't work.
View detail