Reviews
Simple is good.
I used to use Axle Cup, but I decided to use Slider because it is a "Chain". It is smaller than I expected, but it looks OEM.
I think it is also the strongest in terms of cosmetics.
View detail
antlion antlion Rear slider
antlion antlion Rear slider
Items that should be purchased for Motorcycle protection.
View detail
antlion antlion Front slider
The least expensive product in Slider
Custom parts are gradually being discontinued.
I should probably buy it to protect Motorcycle.
View detail
For peace of mind.
Purchased the product because it was equipped with Over Rear Sets and Sliders.
The sense of unity has been improved by matching the logo,
The product was easy to install without being too subtle, and it was easy to install, but I applied a little Locktite just to be sure,
View detail
Cosmetic! For protection of Axle Shaft.
[How is it used?
Used at Circuit. The screw thread of Axle Shaft was almost crushed when it fell down without being attached.
Was the one you received as per Image?
Yes.
Was the installation difficult?
Just pull out the SHAFT and insert the Cup between both SIDE.
However, if you assemble the Rear Shaft without thinking about it, as has been your habit, you will have to redo the whole thing.
You might want to get into the habit of putting Cup in the beginning.
How was your experience with it?
I haven't tipped it over yet, so I can't give an imprementation, but it is solid and secure for the low price.
The resin Cover is removed, but still high enough for Shaft protection.
[Included Parts:were they on?
It had parts to accommodate M10.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
If I had to say so, I would say that the length of the resin slider could be a little shorter, as it seemed to hit the ground in the Circuit.
View detail
I'm not particularly indebted to you.
I put it on because it's kind of a standard product, but it could have gone either way.
It would be self-satisfying because normal people don't look at these places.
MotorcycleParts, as you might feel if you're also tinkering with cars.
There are a lot of smalls and not as Impact as a car.
For example, Squid Ring.
View detail
Fits: SUZUKI GSX1300R HAYABUSA
22 HAYABUSA It would be nice to have a 1/4Socket for installation.
This is a general type of Penetrating Axle Shaft.
The 13mm lock nut is tightened with Both Sides, but the entrance is narrow and it is difficult to reach the nut with 3/8Socket. 1/4Socket can easily enter the nut and tighten the lock nut.
It is recommended to work with Socket, which is thinner in thickness.
View detail
more than expected
Installed with no problems. It looks better than expected and I am satisfied. View detail
Fits: BMW R nine T, BMW F800ST (STRADA), BMW R1200S, BMW F800S, BMW F800R
555B030 is not compatible with 23’RnineT
The thing is good, but unfortunately the conformity information was wrong.
I cried myself to sleep when I realized that the return and exchange deadline had passed.
By the way, the picture is also different; it is not the Type that is Axle ShaftPenetrating, but the Quantity.:Pair (for Left and Right) The independent one came, but so did the Manual with the model number, so perhaps the photo is different.
View detail
Funnel Type, so Parenthesis is good!
I think the price is high for what it is, but I like the look of the Funnel Type!
It is easy to install., to One point!
Happy with the results!
View detail
Fits: KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX1200DAEG, YAMAHA XJR1300
Exclusive Design
It came on without any problem because of Exclusive Design.
It is installed by insurance.
I would be careful not to use it.
View detail
Fits: YAMAHA FZ-10, YAMAHA MT-10 SP, YAMAHA MT-10 SP, YAMAHA MT-10, YAMAHA MT-10, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1M, YAMAHA YZF-R1M, YAMAHA YZF-R1M, YAMAHA YZF-R6
Gilles axle sliders YZF-R1
DOing a little bit of protection for the R1 recently and decided to go for the Gilles tooling axle sliders. I have used Gilles for protection before and have had really good results even after them getting some action. I found the correct part from Gilles tooling webisite and then searched Webike for the corresponding parts. Luckily, Webike do have quite a lot of R1 Gilles items in stock. Get in the basket. These were part of a larger order as this also saves me money on the amount of shipping. I use now EMS fast as they have never let me down. Even from Japan to the UK takes 4-5 days total. This time around, most of the parts were already in Wrbike warehouse so they all arrived in 5 days. I do love the way Webike package their orders. They take great care in packaging well and keeping everything separate and individually packed. if there is any space, they fill that with extra padding like bubble wrap and/or air pockets. This was the case on this order. Although the box these came in was relatively samll, they are kind of heavy for what they are. The last thing I wanted was for these to be moving around whilst in transit. Not with how Webike package items though, thumbs up for that one. The axle sliders arrived in perfect 100% condition as you would expect. ALl the manufacturing from Gilles is exceptional. They really do know how to make parts and make parts to the highest specifications and quality. They do not take much to fit them, simply a couple of bolts and away you go. If for any reason, these do see the tarmac, I know they are going to do their job as intended. Gilles, you are a superb brand and I am very pleased Webike stock your parts. Thank you Webike for the great service provided with this and all my other orders View detail
Fits: YAMAHA FZ-10, YAMAHA MT-10 SP, YAMAHA MT-10 SP, YAMAHA MT-10, YAMAHA MT-10, YAMAHA NIKEN GT, YAMAHA NIKEN, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1M, YAMAHA YZF-R1M, YAMAHA YZF-R1M, YAMAHA YZF-R6
Gilles Tooling rear axle sliders
Having already decided to purchase the front Gilles Tooling axle sliders, it was only right that I also purchase the rear axle sliders. I found the correct part from Gilles Tooling website. Then again, luckily, Webike also stock the rear axle sliders too. Brilliant. I could probably get these shipped direct from Gilles at around the same kind of price but then I woul have to hope they package their products accordingly. Ended up just getting averyhting from Webike. There were already the front axle sliders in my basket and a few other smaller bits and pieces. The shipping because of this was a lot better value than if I purchased just one or two products from Webike. I use nowadays, EMS fast. The service is spot on, everything is delivered in rapid time, when I say rapid, I mean from Japan to the UK in less than 5 days. All the parts in my order were neatly fitted into a smallish box which Webike took the liberty to seal on the outside. The inside was well packaged and these guys must be great at Tetris as they got eveything in the samll box without compromising the efficiency of the extra packing. They filled any gaps with bubble wrap and air pockets. When these arrived, you can just feel the quality. All the machining is perfect, no weird burrs or shards. The paint is flawless and you also get a couple of different coloured rings which should suit anyone's needs. Fitted really nicely and the overall result is a great looking bike with protection I know I can trust just in case. Very pleased with my purchases, thank you Webike View detail
Rear Axle SliderShaft is too short to install.
You should not buy it. It will be a waste of Gold. View detail
Emphasis on decoration
It was the first product that came out, so I installed it, but it is a little expensive. I was glad that there were no decorative elements in this part, such as the decorative plate on the base or the aluminum collar, which is not visible after installation.
Quantity:Pair (for Left and Right) Note that two sockets of the same size are required because they will be supplied if they are not held from the
I don't know how effective it is because I haven't tipped it over. (I feel that if the bottom case is tipped over in such a way that it is damaged, it would not be enough to protect Axle.)
I think it would be easier to attach and detach if one side is fixed, but I don't know why.:Pair (for Left and Right) It is a hassle because you have to hold it down from the
View detail
Need a thin Socket
I was glad that there were no decorative elements in this section, so it was Simple and inexpensive.
The clearance between the Body and Bolt is narrow, requiring a thin-walled Socket.:Pair (for Left and Right) Note that two of the same Size are required because they will turn around unless they are pressed from the
I don't know how effective it is because I haven't tipped it over. (I feel that if the bottom case is tipped over in such a way that it is damaged, it would not be enough to protect Axle.)
I think it would be easier to attach and detach if one side is fixed, but I don't know why.:Pair (for Left and Right) It is a hassle because you have to hold it down from the
View detail
Exactly and Fit
Exactly and Fit. It looks Good.
Installation is easy and takes only 5 minutes.
My concerns are that the fixing rod that goes through the shaft is cheap and seems to rust over time, and that it can only be fixed with a weak torque.
Screw lock is a must.
View detail
Fits: KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R
Damper effect expected
Sliders with a single point of attachment are at risk of damaging the frame, but this product was selected because it has a built-in damper to dampen the impact.
It is hard to tell how effective it is because it has not been tipped over. It seems to be less stressful on the mounting area because it has little overhang for its thickness.
I like it because it is a shape that does not make much of a statement.
View detail
Quick change style
I chose it because it looked cool, like the Slider cone on Racer's Quick change.
It was replaced with an external Axle, so it was lubricated and adjusted by wrapping a Rubber plate around it.
The texture was not good for the price.
View detail
Fits: KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI ZZR1400 (ZX-14)
No fit feeling
It was a compatible model, but it was too loose to stop, so we wrapped a rubber plate around it and adjusted it.
Split Pin cannot be installed because it is inserted in a hollow Axle.
View detail