Reviews
Pay attention to mistakes buying! Let's see the plan of the product!
I misunderstood the information on the product name of Tanax and received it, mistake in purchase (Upside down Screw diameter) I did it..
In Tanachi "M8 -> M10" Is an adapter that converts M10 to M8.
ProductNo for those who want to make LITTLE CUBM 8 OEM Mirror M10 Mirror 【C-1 or CM-1】 Is correct. C-2, CM-2 are wrong.
I was convinced for the first time by looking at the image of the plan view at Webike to buy again.
Originally the product title of Tanax is confusing.
Although I commented as a bad point, the expression method of the product is too bad.
In this case buy mistake victims should come out. (I gained momentum for Large on other purchase sites)
The product is just installed, so corrosion resistance is the future verification.
View detail
Visibility improved
I exchanged Handlebar from American to Separate and the height was low and the visibility of Mirror got worse so I installed it.
It is about 20 mm higher, contributing to visibility.
Since the surface is black dyed, it is easy to rust after tightening with Wrench.
View detail
Used for Rear suspension extension
Commerce Product No 9321.
I used it to extend OEMRear suspension of old and new Dio 110, PCX.
Only this adapter can be + 10 mm.
View detail
Looking for ease of view
I installed it on MONKEY.
Mirror has changed shape,
Because it was difficult to check backwards
Since it was that the range that can be seen increases as the height is raised, I bought it.
As a result of installing, I think that feeling became easier to see.
The part where the shoulder was reflected so far became visible to the back, so it is not bad.
However, it is not SMART as an appearance.
Although it is 20 mm Up, there is a feeling that it has been upgraded as it is.
However, since you can also choose the color Black and Plating, you can choose according to Mirror.
I think that it may be cheaper to make a little more gold.
However, since it is a gold amount that does not hurt even if you think that it is subtle, it may be that you try someone who is hard to see Mirror now.
View detail
It's 3 centimeters long and 3 centimeters away
I only saw my arm until now, so I was thinking of Offset. Since it can move only about 3 cm with the Adapter attached, it was uneasy how effective it is until installation. I can see the backward firmly except for. Because it is expensive Parts, it was good not to fail.
View detail
Visibility improved and satisfied
I am satisfied with better visibility.
To illustrate It is sold by piece. Because I did not write it I ordered only one.
If you order another one, it costs a shipping cost and it becomes a high thing, Quantity : Pair (for Left and Right) It is hard to use the things with different heights, the worst.
I'd like to order together when ordering something. Until then, I'm tolerant at the height that I can not see until now.
View detail
It is necessary to install Mirror in GROM
It is necessary when Mirror is installed.
It interferes with Right Side 's Brake fluid tank, so this part is needed. Right Side I do not need it, but it looks so inclined that both are necessary.
Screw attached when attaching Mirror (hexagonal) Do not tighten Bracket directly with Spanner as you will be tightened at !! It will be full of scratches.
View detail
It is necessary for safety and white by tracking measures!
Please install it on a vehicle with a low Mirror position.
Since the position of Mirror rises by 10 cm, visibility improves and it is the best product for safe driving. * It will be easy to notice even in the tracking by White by.
Compared to Mirror's male Screw's length, the product's male Screw's length is slightly shorter. If it is 3 millimeters more, it is a 5 star..
View detail
I should have done it from the beginning
Neck was expensive everyone's impre street.
It's higher than popular Mirror selling here.
I purchased an inexpensive competitor OffsetHolder, but I can not move to the position I expected but another Size is already Quantity : I purchased 1 Set.
As a result, it is short and long in the belt...
I was able to install Mirror at the position that I thought to buy just one item of this product by any means.
A total of 4 items of wasteful company.
This Quantity : 2pc. It has become price equivalent to Set.
I feel that Design is also better to this person.
After all, the product to change Position is useless unless you have the adjustment function.
View detail
Installed with Mirror of Mukawa in Grom
It is only 2 centimeters, but I felt it changed quite a bit. It is my impression, I think that it became a little safe.
Originally, Mirror of Grom is a round type, but it is changing to a long side. As you can confirm the backward without dropping the line of sight a little, as you can see the back at the height close to the shoulder, by thinking that Mirror is upwards, I think that the reflection of the arm will decrease a bit and replacing it Was.
In addition, somehow, I think that I can ride my posture well.
I do not even feel that the tremor is great. (I think that it also affects because I attach Handlebar Brace and Hand guard. )
View detail
Purchase by rust prevention
I tried to attach MIRROR made by Tanax to MAJESTYS via Takatsu's anti-theft adapter and it was not possible to attach because Screw diameter did not match. (I am not good at checking myself, but - - - )Quantity : 1pc. So Left Side 10 mm positive → 8 mm positive, Right Side 10 mm positive → 8 mm reverse (Mirror → Motorcycle) I bought each. Installation was fixed with a high strength Screw loosening prevention adhesive so as not to be stolen from the root.
Material : It would be nice if there was a Black of Stainless Steel.
View detail
8 mm to 10 mm
I will convert the diameter of Screw at the base of Mirror, but since it was attached to Mirror, I did not use it after all.
However, if it has this, it may be quite useful. I can use it in other places.
Making is good.
View detail
Utilized for Yamaha OEM Mirror
Yamaha OEM Mirror for SR 400 (Opposite Thread Screw, previously used for WR 250X) There was a surplus, I thought that I wanted to add to HondaVT 250 SPADA, I bought it. The body side of SH 10 is Normal Thread Screw, the side of Mirror is a reverse screw correspondence product. Naturally, it was easy to install. Mirror for SR is 1 to 2 cm wide wider than NORMAL of VT 250 SPADA, good rear vision.
This VT 250 SPADA is equipped with ETC loading Bracket of Tanax. In order to clap its Bracket by handlebar, I move the Mirror Holder on the Brake side to the inside. I regained that visibility deterioration.
It is also solidly made, recommended for utilizing YamahaOpposite Thread ScrewMirror.
View detail
Mirror installation of KSR 110PRO
The acquaintance attached Mirror under Handlebar is often Parenthesis, purchase, part cut part is obviously wanted to imitate, but impression that there is no part that cuts hands such as BALI and it is not bad despite price was.
After actually installing it, I closed the Screw in the place where the Handlebar was bent, and it cracked quite easily. My mistake I did not put on the straight side of Pipe.
I finally got it like the picture below. The degree of freedom of installation is high, I think that not only Mirror but also various ways of using it are cheap.
View detail
Purchased for bulk by Mirror exchange
When replacing from OEMMirror to Mirror of Other Company Product, the height lowered and it became hard to see, so I bought it for the bulk of height earnings. It was Mirror of Japanese Vehicle Inspection Correspondence, but if you have Turner it may be useful if it is used? Because it is a product that shows its effect when you touch it Fortunately I have not confirmed the effect yet and I will keep 3 stars.
View detail
POSH Mirror Adapter
OEMMirror of MONSTER S2 is fixed with M8 Bolt. Since M10 has more choices than M8, I exchanged the parts clamping Brake and Clutch Master cylinders with for M10.
The color of Handlebar also matched and it felt tightened.
View detail
Tanax Napole for OnTANAX NAPOLEON Mirror
Purchase for height adjustment of WR's Mirror. I changed the opposite side to Mirror Adapter outside the company in order to attach Mirror downward to WR, the height of Mirror changed and Quantity : Pair (for Left and Right) The way of looking is also different, fingers were caught on Mirror even at BlinkerCancellation but this is a problem solving ◎ View detail
Ideal for those who feel strange just above Handlebar.
I installed it in KDX.
Mirror Holder of the OEM Product is attached to Mirror directly above the Handlebar, so it is necessary to climb Standing etc.. Since it can be done so far I did not attach Mirror of Left Side - - -
It is a bit awkward because it needs a certain strength, but it's heavy, but the Conversion Adapter of the Handlebar diameter is also firm and easy to install because there is the attached Wrench,
Not so much Mirror on the front side, but there is nothing to worry about in the forest road and I also like the position of Mirror.
View detail
Although it is a slight Offset
I do not like the position of RightMirror of KTM EnduroR, I want to improve the visibility of the backwards.
Although it is only a small movement, in the case of my Motorcycle, the backward visibility has improved very much.
(Depending on the vehicle. I think there is LargeSmall for interference and improvement with the car body)
It is a long hole, but it can be firmly fixed.
It feels a bit expensive, but it's Cut-out so there's no choice.
View detail
Purchased with Mirror exchange
When exchanging OEMMirror, conversion from 8 mm to 10 mm is required and purchase.
I am satisfied with the look that does not feel uncomfortable.
If you desire Quantity : 1pc. I want you to prepare the goods of.
View detail