Reviews
It is good to be able to multiply with Chain
When removing Wheel, multiply Swingarm with Dustcloth
It will cure by preventing scratches by Chain
It is convenient to be hooked by this hook.
But I wonder if I will put Dustcloth in front of Hook.
Installation of Chain cover Nut (6mm) Is not used
Carbon fender's Chain cover part
Cut and install it to the rear side.
It's an Anodized Treatment so it looks nice.
View detail
Great?
Only Release was changed before MASTER change. It was easy to install and even an amateur could do without problems. And the change of Clutch is wonderful? Lever and Pedal are lighter. I am looking forward to the combination with MASTER. View detail
Dress-up to Celebrity
I installed it with Accent as RODFixing Screw of Shift change.
Compared to normal M6 Nut, it is much expensive but satisfied.
Let's tighten securely with the tool after adjustment. Because it is inconvenient to lose it by dropping it.
View detail
Fits: HONDA CB1100, HONDA RVF750, HONDA VTR1000SP, HONDA VTR1000SP, HONDA X4, HONDA CB1300 Super Four, HONDA CB1300 Super Four, HONDA CB1300 SUPER BOL D'OR, HONDA CBR1100XX SUPERBLACKBIRD, HONDA VTR1000FVTR1000F FIRESTORM
CB1300SB 2015
Since I thought that Clutch is heavy from now on, it got lighter and became easier when attached.
It seems I can tour it fun again with this.
I think that appearance has become quite fashionable.
When replacing, there are various necessary items such as Brake fluid, so please prepare thoroughly.
View detail
It is fingering story. It may be conspicuous.
? 【What made you decide the purchase?】
Because it is an old Motorcycle, Brake master cylinder is cloudy so I purchased it with deterrent suppression.
In Race, I imitate to prevent bleeding and scattering of Fluid, but I feel good as fingering Parts.
? 【How was it actually used?】
S Size is just right. I assumed that it would become Oversized, but I was satisfied because it was Exactly.
? 【Was it difficult to install? (Hard parts case)】
It's just covered, so no problem at all.
? 【Please tell me the point of installation and hang (in the case of Hard parts)】
As TSR characters can be seen - - (Lol)
? [Is there anything I was disappointed about?]
None
? [Request to Manufacturer - Please let me know if you have any improvement points]
It is good to have SS Size in for Clutch.
? 【Have you compared items?】
Especially None, A little Price is high - - ??
View detail
Fits: HONDA CB1000R, HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Stainless Steel's texture is good (^-^)
I used POSH's Aluminum Bar End, but Material : I changed it to TSR 's Bar End in connection with Stainless Steel.
We do not run with installation only yet, but different from Aluminum (Small, but weigh as much as OEM) There is so I expect to be able to reduce the vibration of the Handlebar somewhat more than before.
After all, there is only Honda exclusive item, compared with POSH it is not sandwiched between Plastic's half moon type Attachment, Body is processed into Exactly shape and satisfied with the texture of the product.
View detail
Quantity : 1 Set of 2pcs. I thought that..
I tried to use it normally as a Wrist band, but Quantity : 1pc. What is it?.
Quantity : 1 Set of 2pcs. I misunderstood.
Well Design is good as it is good.
View detail
Beauty is being well built
Since running around Tail and Rear suspensionUnit become dirty,
I was looking for a Fender that can be attached to ABSMODEL.
TSR's product is also well shaped, Material : Even though it is Carbon, it is relatively inexpensive and therefore purchased.
Manual is difficult to understand a little, and OEM's Rear suspension Cover (?) and,
Chain guard must be removed.
Also remove the fixed parts that keep Brake and ABSCable in Swingarm,
After covering the Fender, fix them in the form of holding them Bolt in those holes.
It is also written in the Manual, but my 1000 RR has a high welding pit of Swingarm,
Several attached Washers, fixed with the adhesive on the back of the Fender and installed.
Tighten Nut and File Processing etc. It fits perfectly to the car body without the need of it, so I am satisfied with the high parts accuracy.
As a precaution, since it is necessary to detach several times when adjusting, in order not to damage the part of Swingarm at the end of Fender,
Tapeetc. It is recommended to curing with.
View detail
Cool
I purchased TSR's Wrist band this time, I am satisfied with both Cost performance and performance.
I will recommend !!!!!
Please try using everyone !!!!!
View detail
Fits: HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR
Aerodynamic design is Parenthesis nice
With Double-sided Tape and the attached BoltCollar,
Mounting using the boss hole for Stand Hook
Since it can do, drilling in Swingarm is unnecessary.
Remove attached Color, Can be used with Stand Hook.
Race base When installing on a car, some Cut processing is necessary.
Included BoltQuantity : Fix to Swingarm with 2pc.
Aerodynamic design with thickness and irregularities is also Parenthesis nice.
The price is about 2 when compared with those of other companies. Approximately 5 to 3 times.
★ If you are a bit cheaper ★ 5.
View detail
Fits: HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA VFR800, HONDA VTR250, HONDA HORNET250, HONDA CBR250R, HONDA CB400SF, HONDA CB400SF, HONDA CB1300 SF
For 98 VTR only 1 cmBack
1cmUp / As for Back, 98 VTR was thick because footpeg was thick, so I could not expect it. To be sorry.
Just because I do Back, I came to an awesome position for me to lower my ass backwards. Left Side is replaced after photo exchange. Length is slightly shorter than OEM, but I do not care much. Good with Pin is Good.
Although I ran back about 20 km, I feel back, but Position does not change Large. Height 170 cm, shoes Size 25. It is 5 cm, but Pedal operation is also uncomfortable. I changed to Gold Genius and thought whether I felt the vibration, but it does not change much like Large. Shoes slide as usual. It can be used without incongruity, but it is easy if you back it for a while.
View detail
Excessive expectations for change are forbidden.
CBR-1000RR (Late SC - 57) The hydraulic clutch was hot, and about 300 km of Touring was about to make Left hands ineffective. At that time there was no budget, so I installed TSR's Release.
I also thought that it was a bit lighter at the beginning, but I got used to it soon and I could not understand it at all, so I did not improve the spicyness of my hands when I went to Touring.
Since I got rid of OEM's Clutch release, I put GALE SPEED's Master cylinder in the TSR's Clutch as it is.
I also consulted Manufacturer, 16 φ for OEM Clutch release, 17 for TSR Clutch release. If 5 φ it was Large and it was sturdy.
So I am 17. 5, but it got dramatically lighter. Please refer to those with the same trouble by all means.
View detail
IMPRE
It was the CBR 1000 RR's slave Cylinder exchange for the first time, but I think that it got the expected performance that Clutch will be lighter by replacing! View detail
Fits: HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA VFR800, HONDA VTR250, HONDA HORNET250, HONDA CB400SF, HONDA CB400SF, HONDA CB1300 SF
TSR Sports Footpeg Bar Set/Standard
According to NORMAL's footpeg, depending on Boots, because Change Pedal's operation was hard to do, I chose this product to move footpeg. Position change amount is Back 1 cm, Up 1 cm is exactly good, and operability has improved. Also, since the Exhaust System is also manufactured by TSR, it is satisfied that we can arrange it at the same Manufacturer Parts.
View detail
Looks good Parenthesis!
Because it is WorksStyle of all Japan Parenthesis nice.
Because the Inner Tube is covered,
It seems to protect us from scratches by stepping stones.
I think there are individual differences, but the R part at the tip of Fender is
Quantity : Pair (for Left and Right) Hitoshi etc. Instead, it was cut into sundry.
I need to apply Screw lock agent to Bolt of installation
High risk of falling off due to vibration.
View detail
Looks exactly Works!
Footing is generally good,
There may be individual differences in products.
In order to divide, look after the coalition Quantity : Pair (for Left and Right) perfectly
I am not going to say Exactly.
Slightly different spacing of parting lines,
There are very few gaps etc.
But it is a few millimeters Level which I do not mind at all.
Well, maybe it is useless if you are a nervous person? (LOL laugh)
Depending on the product you purchased, slightly matching the current car
You may need to scrape it.
I think that it is also within the acceptable range.
As a person who has ever bought such as Cowl outside the company
I think that you can understand.
It is a shape that covers the entire Front fork,
It seems to protect Fork from scratches such as stepping stones.
Also, since it is GPStyle, it seems to be effective also in aerodynamics.
It can be split back and forth by Quick fastener,
Tire exchange, Maintenance efficiency UP.
Front stand is also easy to hang by splitting.
It is not limited to mere Dress-up parts,
Practical things were also thought Parts.
View detail
I attached it to VFR 800F
Installation can be put on the Chain cover attached from the beginning.
Chain cover is Brake hoseetc. Since it is fixed, it is easy because you can avoid hands on it.
It is a nice Parts because car wash is easy as mud bouncing is also reduced.
However, because the price is high, I hesitated when I bought it.
Design is recommended because it is beautiful.
View detail
CBROwner's classic products?
This does not improve the performance of Motorcycle, you can expect the effect of the rider's feelings to increase.
Since various colors are prepared, it is kind that you can enjoy Coordinates with Motorcycle.
View detail
Fits: HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA VFR800, HONDA VTR250, HONDA HORNET250, HONDA CB400SF, HONDA CB400SF, HONDA CB1300 SF
Slight improvement
Even a little calf will hit the footpeg when stopping
I bought it as if I could improve it.
The result is a little better now.
I also thought about purchasing Rear Sets but because it is expensive
It is hard to get out - - - This product is enough and w
Because I did not want to reuse Split Pin,
I bought it at Home center but it was attached ^ ^;
It does not have to be bought w
View detail
Fits: HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA VFR800, HONDA VTR250, HONDA HORNET250, HONDA CB400SF, HONDA CB400SF, HONDA CB1300 SF
Simple Rear Sets
With only simple replacement of OEM's footpeg, installation was also very easy with 1 cm UP 1 cm Back.
CBR1000RR (SC 57 of 07) I could exchange with Slotted screwdriver and Radio pliers to exchange.
I bought a Short Type but since it was a length almost unchanged from OEM, it was the correct answer by choosing the Short of here, not the Standard Length.
Because there is no Knee Slider, bank angle can be earned more than OEM.
Rear Sets is also good,
Is not it the best item for those who want to increase the amount of folding knees but want to back & up just a little more.
View detail