Reviews
Does it work?
I was curious about the vibration of the FZ1 FAZER, so I popped it in. I've been using it for a while now, but I'm not sure if it's worth it. I'm going to use it for a while. View detail
Hmm, subtle?
When I replaced the Handlebar, I was concerned about vibration, so I did some research and purchased this product.
Initially, I felt the slight vibration more than before I put it on. I think this is counterproductive. I thought it was a good idea, but lately I don't mind it anymore.
I don't know if it's because I'm used to it or if it's because of the effect of the Parts.
I've been wearing it for a while now.
View detail
It will be reduced to some extent, but not to Zero.
[How is it used?
Installed when replacing with SNIPER's Handlebar.
Was the installation difficult?
A Hexagonal Wrench is easy to install, but a Bolt is required for removal.
How was your experience with it?
I introduced it because I had replaced the bar end weight with a lighter one and the vibration increased.
The vibration that made my hands numb and itchy has been reduced to a level that doesn't tire me that much even after a long run. I can't say that the vibration was reduced to zero, but I could feel the effect of the reduction.
If you want to replace the bar end weight with something you like the look of, but it is too light, you should consider this product.
[Notes]
It is not compatible with the OEM Handlebar of the Ninja 400.
View detail
Very nice parts
Nice parts and fast shipping. Extremely satisfy with the product. Fit the bar handle without additional adjustment. ;) View detail
I introduced it as a numbing agent, but...
I installed it to prevent numbness in my hands due to vibration, but unfortunately it had little effect on my Motorcycle.
"Better than nothing." It was a degree.
I guess the effect varies by car model and Handlebar.
By the way, the Bar End diameter of rizoma is 17mm, but I chose 13-17mm compatible because the back is narrower.
View detail
Parts that are the power behind the scenes
Because it exchanged from the OEMSeparate handle of 14-year type MC41 CBR250RSecond Type Model to the Separate handle made by Active, it purchased at the same time for the measure against vibration.
I bought it at the same time as the Separate handle just in case I didn't need it if I didn't have to use it, but as it turns out, it was a good purchase.
Separate handle for Active's MC41 fits for 13-17φ.
Inner WeightQuantity of One Side 148g in the product Package:Pair (for Left and Right) That's all I need, but I don't need anything else.
If I had to say, it might be kind if it comes with Hexagonal Wrench for installation.
The body is made of Brass and has two widening rubbers when the bolt is screwed in.
There is a screw mount for a long bolt to pull it out from the handlebar, which is very thoughtful.
I think it's better to keep the original appearance of this product rather than increase the price by adding cost.
To install, screw in the Bolt to some extent, and spread the Rubber until you feel some resistance when inserting it into the Handlebar.
Simply push the Bar End into position and tighten the Bolt to secure it in the Handlebar.
Be careful not to accidentally insert it too far in.
Not only does this make it more cumbersome to remove, but it also reduces the effectiveness of the Handlebar as the vibrations become stronger as you move towards the end of the Handlebar.
I've used it and it clearly reduces the vibration and shaking of the Handlebar.
… but unlike a multi-cylinder engine, the MC41 is a high-revving single-cylinder engine with a lot of micro-vibrations, and it seems that the micro-vibrations at high rpm cannot be fully absorbed, and the micro-vibrations are clearly higher than at the OEMHandlebar&Bar End.
However, because the vibration becomes like the corner is removed in combination with the reduction of fine vibration (It's hard to describe …) It's not as uncomfortable and my hands don't get numb over long distances anymore, so I've decided to use it as is.
If you want to eliminate the slight vibration to OEM same etc., you need to replace the Bar End with a heavier one.
I think it is good to buy it as a setting parts to find the point where you can compromise with Bar End. I think that it is good to buy it as a setting parts to find the point that I can compromise with Bar End.
It's more cost effective than buying an expensive Bar End.
View detail
For vibration countermeasures
I have them on most of the Motorcycles I own.
It is effective for vibration control.
It's not a dramatic improvement, but when you notice your hands are less numb than usual, that's Level.
The effect will vary depending on the shape of the Handlebar.
It seemed to work well with the Aluminum Handlebar.
View detail
ใช้ถ่วงนำ้หนักแฮนด์แทนของเดิม เพราะจะใส่กระจกปลายแฮนด์ สินค้าคุณภาพดี สมบูรณ์ ไม่มีตำหนิ จัดส่งเร็วกว่ากำหนด View detail
So bad
I bought this because I thought it was unusual to have a screw cut directly on the weight part, not Pierced Type.
I was planning to use it with the Bar end mirror end, but the screw hole for this product is 4mm.
Because the screw of the bar end type is 6mm large, it is necessary to process small.
View detail
Very effective Large!
The vibrations are gone, far beyond my expectations!
You can clearly see the difference in the long exposure photos.
However, because the Handlebar inner diameter of my Motorcycle was φ17, I purchased the φ17-20Type, but that one did not fit in the middle (it was claimed to be from φ17, so I'm waiting for a response on my objection to return it. I'm waiting for a reply.
I couldn't wait until it was too late to respond, so I bought another φ13-17Type, and this one's perfect! If you're on the fence around φ17, I'd recommend φ13-17Type!
View detail
It's neither good nor bad
[How is it used?
Introduced along with the change of Separate handle of XJR1300C in the town riding and Touring Main.
Was the one you received as per Image?
I had it in my old MainMotorcycle and it is as Image.
Was the installation difficult?
As long as the inside diameter is correct, there is nothing particularly difficult to do.
However, although the Handlebar I.D. supports up to 17φ, when tightened with 17φ, the
You should put Washer in there because Nut, the turning stopper, will come over Rubber.
How was your experience with it?
The vibration of the Handlebar has been reduced. But of course, the Handlebar itself is obviously heavier.
[Included Parts:were they on?
It is as shown in the product image.
[Was there anything that disappointed you?
If you tighten it up, the Nut will be buried in the Rubber and the Torque will be gone.
View detail
Effective for vibration reductionLarge
I used it for my Made by HURRICANEHandlebar for my REBEL250.
I recommend it because it can reduce vibration considerably.
View detail
Hurricane balance weight terminal
Hurricane balance weight terminals can be used on hollow handlebars to achieve weight balance to reduce the tragic vibration of motorcycle driving and cause discomfort to the hands after long riding, and Hurricane balance weight terminals can be installed with external terminals to add personal style , Will be installed immediately after delivery! ----------------------------------------- ----------------- Hurricane counterweight terminals should be used to reach a hollow handle counter-balance to reduce the miserable life of the motorcycle driving vibration which causes discomfort FLAC part of a long ride , and Hurricane counterweight can install terminals outside the terminal to add personal style after delivery of the vehicle will be installed immediately! Powered by Google Translator View detail
Might be pretty good! Please take a look at our feedback
I think the results of this type of product are quite different depending on the environment and how it is installed.
I put it on this time to counter the fine vibration of Kawasaki MACHH2 2nd.
Handlebar is 17cm UP iron PlatingHandle type
Mirror is a (Earthquake resistant measures have been taken) M-TEC Chukyo:M-TEC Chukyo Item number:MRS-IM-MK02CA
This was a little better, but the addition of Inner Weight in the Handlebar makes it even easier to check backwards.
I think it has improved safety.
If you are in a similar environment, I recommend it. Try it! (^^) /
View detail
Inner Weight
When I installed it, I tightened the bolt to fix it, but I couldn't fix it because it was spinning. It is the impression which ran, but it is the feeling like the shiver was reduced a little, but it may be able to experience it more if it runs a long distance, I will write the impression after running a long distance next time. View detail
As expected, it's a perfect fit.
I've bought it before and used it on another vehicle, and it's great for handling Handlebar microvibrations without a huge Bar End.
I'm grateful that he does a crisp job without changing his looks.
View detail
Hmmm, subtle!
I installed it in the PMC YB aperture style of Z1 To be honest, the subtle vibrations generated from 120km did not go away at all Next, I want to challenge with a little heavier Weight product View detail
Is it good?.
Used for Yamaha BOLT Shoulder Bag.
I installed it together with Handlebar exchange.
So it is not clear how effective this product is, but in practical rotation range there is no unpleasant vibration transmitted to the hand.
View detail
Poor quality
If you tighten Screw to fix it, Rubber cracks easily. There is anxiety about durability with this. The O-ring was easily torn out. View detail
Those who do not expect excessive (^^ ゞ
I attached it to the Handlebar of HURRICANE's YAMAHA BOLT Shoulder Bag. Since weight has already been embedded in Normal handle, Handle custom of BOLT Shoulder Bag is a necessity item!
In fact, Stain - phenomenon peculiar to BOLT Shoulder Bag than Normal handle (Handlebar's blur by letting go) It is a feeling that it has been relaxed considerably.
View detail