Reviews
Cost performance, the best!
Regarding Rear box, it is a specialist of a certain Manufacturer, but it is honestly expensive.
This product is a wonderful product that is cheap, with no cheapness at all.
Regardless of the storage capacity there is no problem, loads can be loaded more than enough.
Do not hesitate to buy it!
View detail
The inside also works as Small
First I thought SH26 would be sufficient and I started to use it, so I decided to say that again because of its convenience, so I tried capacity up. It is caused not only by the originally assumed Rain Wears and Body Cover but also by Inner and Over Pants that I took off, foods and souvenirs I bought.
● Body weight is Base - With Gold included 3. It is 9 kg. (Measured). Install Carrier (Manufactured by Endurance) Considering that the maximum Large loading capacity is 6 kg, including the influence on the balance and the cornering with the car case, I think that this Large fee is the limit.
● Comparative study was on SH 39. Design feels like it is modern today, against here it is rustic Square shape. Helmet selects here as if it is better to be square rather than round if considering ease of packing as secondary. After all the cheapness of actual sales (It became eligible for Sale in good condition) , It is convenient to look plain with a handle. The hand slid and dropped in SH 26.
● Base is Small TypeType (Included with SH 33, 29, 26) It is upwardly compatible with the Small Case and you can install it as it is (The opposite is of course impossible). I do not know if there is demand.
● There is space in Lens, you can afford it with a margin if it is about LED Tape. I tried it as a stop lamp for the time being.
Just to be sure, Reflector should be better, Emon's Reflective Protector (Quantity : 1 Set of 2pcs. ) I pasted it. Size is also exactly good, there is no cheapness like Reflective Tape feeling good. In addition, as insulation measures in the summer, I plan to paste insulation Seat inside.
● And every time, Bracket's position was troubled. The interval is as wide as possible, before and after Quantity : Pair (for Left and Right) Based on the condition that Base is not going too far back, the result of trial and error in the determined Screw hole is this. Attention also needs to be paid to Base distortion due to excessive tightening, and it is handled by Nut and Washer on hand. I pasted Black Film on the part where Bracket seemed to be visible from the outside.
View detail
I feel like I can go to Touring anytime!
It is a Rear box that I use for the first time, so I can not compare, but I have a take, I do not have to lock the keys one by one, and I feel like how to tighten the lid even if compared with other companies' things.
I do not know if it can be used for a long time, but I think that I will choose the same Manufacturer next time.
View detail
Fits: SUZUKI BURGMAN 200, SUZUKI BURGMAN UH200, SUZUKI BURGMAN UH125, SUZUKI BURGMAN 125R, SUZUKI BURGMAN 125
I am using it without problems
I think that we support Rear's Case in terms of weight tolerance. SHAD SH 40 RearCase is on board but there is no problem.
It is a place to drill a hole of 16 mm in diameter at Rear's Cover, but the position to determine the center of the hole is marked on the paper, but once you have installed the Carrier by yourself, screws are placed in any position of the Rear cover I think that it is better to open a hole after passing or fixing the position.
I drilled a hole as shown in the drawing, but it was slightly off by a few millimeters and I got a lot of sharp edges in the hole.
In the future, when you replace RearCase, it is limited to SHAD, but it will be inevitable.
View detail
Only installation is difficult point
Klx 125 We attached it to the classic DAYTONACarrier.
Givi's easybox was the subject of consideration, but I felt the appeal of opening and closing without the width or key, decided here.
As in many reviews, satisfactory stability feeling can not be obtained with only the attached parts.
I bought a commercially available 196 mm Bracket and a 50 mm long dish Screw and forced it.
Or, I think that it is not assumed from the beginning that it will be completely installed only with the attached parts.
The purchaser 's efforts are premised products.
It would be impossible to respond to a vast array of carriers.
It took quite some time for alignment and purchase, but I was able to fix it tightly.
Also, we purchased the Hologram Chiyogami paper which is a reflection part at Daiso and realized the red color by pinching it.
Base becomes Large aside, it will be a slightly different appearance, but this is useful for sticking things with this.
I have attached Diske Screw which I did not use to Base instead of Loading Hook.
Unlocking opening and closing is very convenient, but opening and closing in the first place is not a little Smooth.
Moreover, it is surprisingly a yawn exterior, and it scratches immediately as it rubs somewhat.
Capacity is 40 Liter of truly, Mesh jacket and Commuter Bag, Rain jacket can be put in room,
When we paid a big big cap and helmet of Helmet's tour cross 3, I finally crowded Mesh jacket and it got to go in or not.
Tour cross3 is just too big !!
View detail
Fits: SUZUKI BURGMAN 200, SUZUKI BURGMAN UH200, SUZUKI BURGMAN UH125, SUZUKI BURGMAN 125R, SUZUKI BURGMAN 125
Although it is expensive, it is so simple and firm
It is attached to the top box of GIVI.
Simple shape, SHAD, KITACO, GIVI was good, GIVI was good, but it was sold out and the stock was undecided, so I bought it at an ambition to know that it is expensive and holes unknown and worst drilled. (KITACO is load-resistant and Out. Although SHAD ended unknown to the end after all, if CaseManufacturer it was probably Large durable - - )
Mounting is the same as the other, with 18 holes in the car body and fixed with Bolt M8. As I saw in the picture, I forced the hole of Base somehow (I screwed it, but it was not processed. Bolt of fixed body of the picture is changing to SUS in the mood but attached comes with ordinary Black.
Just at Seat in this position fingers Quantity : I think that 2 pc is just good to enter.
For reference, I can work on Wiring as a plate for a hole to be drilled, so I think that one who wants to mess around with it is good.
Stop-lamp is + (Black line on White ground) , - (White line on Black ground) is. Trunk bulb can also be exchanged here, the 2016 formula was ordinary Wedge Bulb.
I think that it may have been good to change to the SHAD top case as it is thought from now.
However, BURGMAN 200 less information - -
View detail
I bought it for going to Camping touring
I bought the first thing in SH 29, I found a handy thing if the Small article goes in, but when it comes to Camping, I have to pay a fair amount - - - I searched for SHAD, I got to this product with its top side flat. I also think that I will do it because I was attaching Rubber ties to this product and a hook for loading, even in WEB search.
Although it is Storage Space, ARAI's Full face and Mesh jacket are affordable and there is room to enter a little Small objects. Because of the same Manufacturer item, we also wanted to thank the pedestal on which SH 29 could be installed. It is a shame that Reflector became White, but I felt it was enough as a function.
View detail
It is only for BirdCity, easy to install
It is heavily surprising and it is quite sturdy.
In the picture of the item description, it looked like a thin plate, but it is an iron plate that seems distorted unless you use it with Hammer.
The hole through which Bolt was passed was accurate and perfectly positioned.
Of course the holes in the Tail cover are necessary, so please make a hole or prepare an open Cover.
Instruction Manual is A4 paper Quantity : 1pc. It is concise content.
Even if English version can not be read, Illustration alone can fully understand.
Recommendation for people using BOD of SHAD.
If you also use GIVI etc., I think that it is better to install a carrier as usual.
View detail
SH29Top case
I attached the SH 29 by pulling the Rear basket of the moped Scooter. Installation was easy to install even without looking at Instruction Manual. It is a very good top case without mounting play. Matching with Scooter is also good. View detail
Because the top of the lid is quite flat, things are easy to put on!
It installed in CBR 250R.
Considering the appearance of Motorcycle of this Class
Is not this the most Large?
From now on Large will be active in Touring.
At the same time I also ordered Backrest but it will take 2 months and I will reorder temporarily Cancellation!
The one that I made four stars was a gold item to fix to Carrier
1 pc out of 4. Because the shape was different, etc.. What was troublesome when installing
View detail
First time "box" is
I am using it for Yamaha's original two kinds off-road motorcycle, XTZ 125.
Since XTZ 125 is an off-road motorcycle, there is nothing to say honestly. In-car tools and documents get in - - - There is not even a Helmet holder because there is a space called Space. Well then it was a troublesome treatment of Helmet on the road, so I decided to install a Rear box.
The reason for choosing SH 29 "Balance of price and Size" It was because it was very good. It is not a value like the famous luxury Manufacturer, but there are many examples of installation on the Internet, there is information, and it is a feeling of Size that Helmet also enters sufficiently, these are the reasons for purchase.
There is nothing troubled by this in actual installation, just fix Carrier and Base with the attached gold accessory. After that, I fix the Rear box Body in a combination of convex and concave, but it is fixed like the information that is scattered on Internet, but here it was very hard. It would be a good idea to blow a Silicon spray one at a time when you feel hard to fit. In my case it worked fine with it, repeating saying it removed and attached a number of times after installation, now it is no longer solid. And since the Base of SH 29 is Small Type, it is better not to protrude from Carrier. Even when the Rear box itself is removed "Here comes Box." The look of Motorcycle is not as it looks but it clears up.
It is the storage performance of the bottom, but Jet helmet 1pc. And push the top and bottom of a thick Rain jacket down - - - In the meantime, what you need is included for the time being. However, there is no room to put in until Rain jacket, so I'm thinking of replacing Pants with a thin one.
Finally, on the Internet "Can open and close without using keys" There is a. It is true that it is, I think that it is better to use the key securely when locking away from Motorcycle or thinking if you are driving while driving.
View detail
Open and close without key
It is appreciated that MAJOR grade Manufacturer items can be purchased at this price.
A good point of SHAD is that you can open and close without using keys. It is enough to use keys when locking (Lol)
Quantity with Size Difference : 2pc. I have a Set, but the regrettable thing is that while driving "Chatter sound" To occur. I cope with pasting Sponge.
View detail
Easy to use.
【What made you decide the purchase?】 I used to use other products of the company before, I purchased because the balance between quality and price was good.
【How was it actually used?】
It is compared with a certain famous G company, but side making etc. etc. Are nearly the same Level. What is more convenient than anything is that you can open and close without using a key. For mopeds with a lot of CHOINORI this is the most convenient.
【Was it difficult to install? (Hard parts case)】 It is time to attach Base securely and it will be over in less than 30 minutes.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Since you can not see the gold tool that gets Base, it is better to find a position to firmly bite the Carrier than to install it in a clean position.
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
[Is there anything I was disappointed about?] When opening the top lid, it closes if it is not open tightly. The cord stopping the lid is short..
【Hope for Manufacturer - Please let me know if you have any improvement points]
Color I also want painted objects to be made. Also, I think that it is convenient if commonality with Base and other companies is done.
【Have you compared items?】 GIVI - Coo etc etc.
[Others] SH26 and SH29 are vertical and horizontal Size is same etc. It's just a different height. Also, Reflectoretc. Even if you think about making the price, there is not much price difference so SH29 may be more satisfied.
View detail
Purchase for Master Address
I bought the original magazine Address but I could not store the Helmet in the full face Helmet in I purchased it. I looked for a Small Top Case that could hold the Full face, but I decided to purchase because Size and price are as you wanted. In fact, even if you attach to the moped, it's a good fit Size.
It seems that the form of Case does not seem to be Large because the back is Sharp. I was able to understand how to install by looking at parts and foreign instruction Instruction Manual. When fixing Base to the carrier, fingers did not enter the gap between the car body and the cargo bed, so it was a bit painful. After attaching Nut and Washer to Wrench with SEROWTape, put it under the loading platform, passed the Bolt through the Base, and installed it.
Durability is now to be expected, but I am satisfied without problems at the present time. If it is durable, I think that star 5 may be good.
View detail
I can not go back anymore.
【【What made you decide the purchase?】
price. It was my first hard case so I wanted it as cheap as possible.
【How was it actually used?】
Because it is attached to SEROW 250, it was worrying about appearance and ride comfort.
The appearance ceased to worry soon.
Ride as expected, the center of gravity position rose and worsened, but I got used to it again.
Practicality is very convenient. Luggage will not get wet even in the rain, if you lock it you will not mind theft.
【Was it difficult to install? (Hard parts case)】
I attached it to the OEM Carrier of SEROW 250 but it was awkward because the gap between Carrier and SEROWBody was narrow.
【Please tell me the point of installation and hang (in the case of Hard parts)】 It may be better to install it with the carrier removed.
Installation is OK with the included Parts.
[Is there anything I was disappointed about?]
It was a much better product than we expected.
【Hope for Manufacturer - Please let me know if you have any improvement points]
This price and quality would be enough.
【Have you compared items?】
There is none.
[Others]
very convenient. I can not return to the situation where there is no case anymore. However, when I got used to it I wanted a Case that is a little bigger.
Far away from Rain Wear, even if Winter Gloves does not even enter SH29 when putting MultiTEC of SHOEI.
So, I punched SH 40. Impre is in.
View detail
More than I thought
Buy 29Liter of Shard and Rear stay for SUPER CUB with Wa Big. Easy to install in less than 30 minutes on both sides. After installation, I tried running in Waitomi but there was no strange noise Firmly I was feeling addicted. Included Bolt also included long and short, so the place to choose according to Bracket was good.
This time we purchase with Bae Wei for the third time. I correspond very quickly and I am satisfied with Large change. If there is opportunity, we will use it.
View detail
Simple
It was Large more than I expected, but it is Design that I do not get bored with Simple. Installation was unexpectedly simple. For mopeds, it is good if there is another small type again. View detail
SHAD SHARE SH 40 Top Case Black
Design and prices are complainant, but
After taking the way of opening and closing up the part
It can not be opened unless it is hard to do.
It was easy to install for the installation.
View detail
Once attached, you can not stop !!!!
Finally committed to handling the forbidden Box!
Looking at this by turning it on (personally) Large I feel like getting into width, but finally put out my hand.
The reason for choosing this is because the shape is square!
In the case of Camping it is thought that it can be used as a table after removing it.
There is capacity as well as 40L, I think that we can load considerable luggage when combined with storage under Seat!
View detail
It is convenient to open and close without a key.
I installed it in SUZUKI GSR 250. I've been using GIVI's Box for many years, but I tried SHAD because it was cheap this time. (*^^*) GIVI always needed a key to open and close, but this box is not very easy to open and close so it is a very easy tin. * The only problem is that the holes are not aligned with the GSR's Multi Wing Carrier at all.
I drilled a hole in Carrier with Drill.
View detail