Reviews
Front caliper is fine! Rear caliper...?
It was useful for Front caliper Piston.......................... View detail
If you're a motorcycle that's regularly serviced, you'll be able to
Cost performance is good
Although it can be used with no problem in Brake which is usually maintained small and diligent, it cannot grasp Piston firmly and slips when movement is reluctant without touching it for a long time.
View detail
Four Wheels for VehicleSpec.
When I inserted it into the Caliper of the two-wheeler, it went in to the tip, but not the whole surface. (There are pictures.)
I turned the Handlebar from there, but it takes a lot of force.
It was difficult to work with the Caliper hanging, so I removed the Caliper from the body.
View detail
Convenient for pad replacement.
The Brake Caliper Pistons are easily pushed back in to replace the Brake Pads, which is less scratchy and more efficient than using Pliers to replace them. View detail
Pad replacement is easy.
It can be used with various types of Brake Calipers to help with pad changes, and it can also be used with 2-pod Calipers to reduce the amount of time it takes to push the Piston in one go. View detail
It can be used normally
There is not much in the way of luxury or design in terms of appearance.
It has been stored in an indoor toolbox and has not rusted for 8 years.
The Grip is thin and painful for a tool that requires a lot of force to use. However, you can turn the Piston with the grip strength of an average man, if it doesn't stick, you can do your best.
Also, I've never felt the need for the Butterfly Screw when using it.
The butterfly screw is used to make it close in Small size when storing. The width is about 43mm up and down without the butterfly screw.
Material is a material that sticks to magnets, so we use separately purchased magnetic holders for storage.
View detail
Two (or three) axes are better
I've been using products with a single-core shaft guide
The structure is severely twisted, limiting its use
I think this product is good for GJ in that regard
View detail
Pretty good
I used it to clean the Piston on the Brake Caliper
Without this product, cleaning the Piston would be quite a challenge
Thanks to this product I was able to wash the Piston and the Touch of Brake is very good! became
View detail
Made by DAYTONA, the trustworthy company
I bought it to clean the Piston when I replaced the Brake Pads By turning the Piston, I was able to clean every nook and cranny View detail
An indispensable tool for BrakeMaintenance
This is a must-have for Caliper overhaul The price is attractive
The whole thing flexes when you apply force to remove the Piston that just stuck to the strength
Also, since the maximum opening size is 37mm, it depends on the type of car, but it's a 2-pot type I can't pinch the Caliper pistons on the..
View detail
It's good enough
I bought this for Caliper OH and rubbing out
Does the Piston of a vehicle left outdoors for 3 years grab no problem? I was able to
This product is very easy to hold in your grip
View detail
useless for the price
I was worried because it was cheap, but I received something that was rather solid
To clean the Brake Caliper, you have to push the Piston back in, but not by hand Impossible
I can do this one
But it's hard to screw in It's hard!
Well, but it's like this
View detail
It's handy for pad replacement
When changing the brake pads, you can use the pliers on the four-wheeled Large Caliper with some creativity The piston was pushed in, but it is difficult to work on the small for motorcycles I bought it because
When the item arrives and you open the box, is it used? I think it's a bit of a scratch Well, I don't mind it because it is a tool
Because Lever is heavy and hard to turn as it is, after applying Grease to the moving parts, the work is done I worked on it and I managed to do the work
I think it's useful for those who often use cars and motorcycles in relation to Brake
View detail
Performance as expected
Although there was also a little cheaper, I thought that it would be cheap and bad ... I made it made by DAYTONA. Cripion is attached to Grip, I think that it is easy to grasp. I cleaned up the Piston Pin of each of the three Motorcycle and used it, but I could use it functionally in any Caliper (If it matches only the diameter) View detail
Strong, long-lasting making
Simple, making is steady. It is heavy because it is sturdy, but I think that it is a product that you can use for a long time. I think that it can be used not only for two wheels but also for four wheels. View detail
It is a price. First of all,.
It's expensive, but it's totally better than nothing. It was good.. No problem at all if it is the first tool. You can relax easily. View detail
You can use it.
After previewing similar products at the Motorcycle supplies store, I also decided to look at other people's impres. Point decided for this product, because it felt that it was harder to hurt the hand than Cushion of the grip part, or thickness, and other Pliers. I can hold it firmly and turn it.. I do not use it everyday, and assuming the frequency of use, I think that it is a tool that can be used for a long time. View detail
It is tough and long-lasting
I tried it immediately, but it is a simple making, and it is a sturdy feeling. Of course Piston pushed back firmly. I assumed it from the beginning, but when you remove Caliper, it is a good idea to prepare a little table so that Caliper will not be dangling with Brake hose and put it there. (When you do not remove Brake hose) I think that it is not a frequently used tool, but I think that if you have one, I think that it can be used for a long time, so I decided to use Cospa as Point. View detail
Absolutely necessary, but unsatisfactory
It is used to grab Piston in Caliper.
To grasp Piston pretty well, I grasped it pretty handly,
It is necessary to tighten up Stopper.
The Stopper is stopped at E type retaining ring,
Absolutely blow away. I can fix it, it is iteration.
Also, Stopper 's Bracket is also weak and it will bend.
You can fix this, though - - -.
The overall rigidity is weak for a while.
So this price is too high. I thought that it was a defective item rather than Level.
I want you to make a more solid one.
View detail
To return Caliper's Piston.
【What made you decide the purchase?】 Required
To return the Caliper piston at cleaning.
Previously, I was returning by hand, but since Piston was accidentally disconnected.
Cheap Prices.
【How was it actually used?】 Required
Just put it in Simple and rotate it. it's simple.
However, it is somewhat heavy and needs attention. With this you will not lose Piston w
[Is there anything I was disappointed about?] Required
heavy. Big.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Perhaps it is for 4 wheels, but I would appreciate it if you could put out items for two wheels.
【Have you compared items?】 Required
There are no products used for comparison.
[Others] Any
Be careful not to drop it as it is heavy as above. It will hurt injuries and Motorcycle. It would be nice to put it on a small table or the like.
View detail