Reviews
Sr400 steering bearing replacement.
I had a little hard work for replacing the steering bearing sr400. This work is needed to bearing puller and small jack for lifting a bike. Also this parts is perfectly fitted to 85 sr400. Thank you for supply this parts. View detail
Purchased due to Screen interference
I put a kappaScreen on my V-Strom 650 and bought it because the Mirror barely interferes with the kappaScreen when it is fully locked.
The interference is naturally gone and I am satisfied with the expected results.
At 6 months and 5000 km, there is no Rust occurrence.
I tightened it securely and it never came loose.
No blurring occurs.
View detail
Z900RS CAFE.
Used to rigidize the handlebar holder of Z900RS CAFE.
The visible cracks on the handlebar holderBush became noticeable, so I decided to replace the bush, but since the Z900RS bush and the old KX250F bush are common parts, I decided to use these parts to make the bush rigid, which I have been interested in for a long time.
After the exchange, the handling is Large-Shaped Solid, and the motorcycle information is conveyed in the same way as a handlebar such as SS without Bush intervention.
On the other hand, the amplitude of the vibration is transmitted digitally to the palm of the hand, unlike Normal, which is felt as an analog waveform, so care should be taken when using Touring Main.
However, the handlebar is raised by 4mm, which makes positioning a little easier in the case of CAFE, and since it is a 2,500 yen part, it can be tried on a no-go basis, including in the event of a problem with a car that is not compatible.
However, it is not visible while driving, and when I looked at Motorcycle again after the test run, it was not as flashy as I thought it would be, and it gives the impression that some customization has been done to the handlebar. It's okay. However, if there is a ZETA Titanium color, it would be better, so I gave it a score of 4.
View detail
It is a reliable HURRICANEBrand with a robust construction.
This product is a trusted HURRICANEBrand and the construction is solid, and there was no sign of cracking even when tightened tightly with Bolt! View detail
Fits: YAMAHA RZ50, HONDA NSR50, YAMAHA TZR50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NS-1, YAMAHA XJR400, HONDA NSR250, HONDA CB400 SUPER FOUR, HONDA CB400 SUPER FOUR
I used it to replace a rusty OEM Product!
I used this product to replace a rusty OEM Product. It comes in multiple colors, so it's great for casual custom! View detail
Fits: KAWASAKI BALIUS, KAWASAKI BALIUS2, SUZUKI GSX250FX, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR1100 RS, KAWASAKI ZEPHYR1100
HURRICANEHandlebar Holder Spacer T10
I wanted to make the handlebar a little higher, and after much consideration, I found one that could be attached to the STD Handlebar Post and installed it.
I have not done a long distance test drive but would like to do so in the future. We recommend that the tank be removed for installation and that two people work on the tank (the tank may be damaged). (The tank may be damaged.)
View detail
Buy at for Repair
I bought it at for Repair.
Wires are important parts, so please read the instruction manual carefully.
View detail
Fits: BMW K1600B, BMW K1600B, BMW K1600GT, BMW K1600GT, BMW K1600GTL, BMW K1600GTL, BMW K1600GT, BMW K1600GTL, BMW R1200RT, BMW R1250RT, BMW R1250RT, BMW R1250RS, BMW R1200RT LC, BMW R1200RS LC
very well & good fit
fast delivery & very fixed parts of R1250Rt. well coated surface & the other part is tightly fixed on Wunderlich adapter. View detail
Tanax Napoleon OffsetHolder
[How is it used?
Used to attach Knuckle Visor.
Was the one you received as per Image?
It was more solid than the Image had been.
Was the installation difficult?
It's not hard.
Need 8mm Hexagonal Wrench.
I went to buy it because it was only available in 6mm at the Largest 6mm.
How was your experience with it?
It needs to be tightened down very tightly.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
8mm Hexagonal Wrench needed and prominently
Would have been nice to have a warning.
View detail
Fits: HONDA NC750X, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR
Used to install fog on Guard pipe
Material:It's aluminum and fairly thin-walled, so I don't think it's suitable for mounting heavy objects.
It is used to mount a Small Fog Lamp.
22.A 2mm Pipe can be diverted.
I have used the same system in my previous car to install fog lights on the Engine GuardPipe, and I have been using the same system in my new car.
It has been about 2 years in total and no Cracks have occurred.
The Pipe side edge is angled, so it is inevitable that the Pipe will be scratched during mounting and positioning.
It is best to avoid repetition of attaching and detaching, including temporary fixing, as much as possible.
View detail
Fits: HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, HONDA REBEL, YAMAHA Majesty (MAJESTY), YAMAHA GRAND Axis (GRAND AXIS), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA GEAR (GEAR), YAMAHA DT50LC, YAMAHA BWS (BWS)
It's nice to be able to buy a lot at once.
Currently, there are only 4 KSR series units.
I bought 100 pieces, 23 pieces on the top and bottom, 46 pieces in total, 2 units
Once I've worked on one, if there are any abnormal vehicles among the remaining four, I think I'll have to work on it right away.
It looks so good ---------------------------------------------- ------------ It is now that the KSR series is only four.
I bought it in 100 pieces.
View detail
M12 M10 conversion
Used for converting M12 to M10. View detail
Fits: YAMAHA TZR50, HONDA NSR250, YAMAHA XJR400, YAMAHA RZ50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NSR50, HONDA CB400SF, HONDA NS-1
To One point around Handlebar
The OEM Adjuster was tasteless looking like faded Black.
It's cheap, easy to install, and it's a great accent around the handlebar.
View detail
Used to install Knuckle guard and Mirror at the same time
[How is it used?
To install the Knuckle guard and Mirror together in a rational way, we used OffsetHolder.
Was the one you received as per Image?
Aluminum Casting and appears to be Black color Painting, not Anodized.
Was the installation difficult?
Technically it's not that difficult, but how many times do you need to change the Handlebar to a Quantity:Pair (for Left and Right) The position was determined by repeatedly making fine adjustments while checking for contact with the Upper Cowl and Screen. In addition to the Offset Holder, an Opposite Thread Screw Adapter (product number:HM-10) from TANAX was used to raise the Offset Holder by 20mm to avoid contact with the Accelerator Wire. For the guard installation, the Knuckle guard bracket was installed from the underside of the OffsetHolder, taking advantage of the long screws in the Mirror Bracket.
How was your experience with it?
We were able to install multiple components together with the Refreshing without any clutter.
[Included Parts:were they on?
M10 Bolt1 pc included.
[Was there anything that disappointed you?
I think it is a little expensive. less than 1000 yen is ideal.
Other items that would be helpful
Mounting points and hang/ All ScrewBolts were coated and tightened with low-strength Screw lock fluid to prevent loosening.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA GORILLA, HONDA GORILLA, HONDA 6VCHALY 50, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA 6VCHALY 50, HONDA GORILLA, HONDA GORILLA, HONDA 6VCHALY 50, HONDA MONKEY (FI), HONDA 12VCHALY 50, HONDA 6VCHALY 70
สินค้าส่งใด้รวดเร็ว งานคุณภาพและสวยเข้ารูป ดีไซน์ เข้ากับแผงคอใด้ดี View detail
Repair item for Set Back Holder?
I bought this thinking it was a Spacer for the Bolt of Set Back Holder, but the diameter didn't match and it didn't fit. View detail
Parenthesis is good, it's been updated.
It's up-dated.
Before
The design surface looks like Rubber Print, and the rubber part deteriorates over time.
present
The design surface is made of nylon fiber. I hope the perimeter doesn't break...
Some people say it's to prevent blisters, but in my case, I just wear it because it's good for parenthesis.
It's self-satisfying, but it increases Tension.
View detail
Exactly what I was looking for
Quick shipping, and exactly what I needed. Thank you! I never ordered from this website and was worried about shipping, but I was pleasantly suprised! I will buy from them again! View detail
RAN Bretta V125's No Mirror also allows you to see the back properly.
For some reason, the screw hole for the mirror is too far inward, so I installed it on my RAN Brettta V125, which has a strange design that only shows my elbow, not to mention the OEM mirror, and even the high visibility mirror of DAYTONA.
The result is Large satisfactory. You can see the back properly.
It's also a great way to keep your style intact.
View detail
Nice try, really nice try……
I bought it to keep my stem area tidy, but it may interfere with some models of sports cars with cowls.
I thought it would be very easy to use for bar handle types like StoFire and NAKED.
Since the Reverse side Nut&Washer is Silver, I bought the Black color separately.
View detail