Reviews
Fits: KAWASAKI ZEPHYR400, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYRX
HURRICANE 10cmLong throttle cable
Long cable was replaced when the handlebar was replaced.
Handlebar is HURRICANE's POLICE2 type with 27mm up set up holder compared to NORMAL.
OEMCable was not enough, so we decided to use a 10 cm long cable.
I think it fits nicely without being too long.
The replacement was done by one person, without removing the carburetor, so it took more than 30 minutes to hook up the new roll of Cable,
The return Cable did not take that long, but it was a struggle.
View detail
Fits: KAWASAKI GPZ900R, KAWASAKI Z1000 (water-cooled), KAWASAKI Z125 PRO, KAWASAKI Z750 (water-cooled), KAWASAKI Z750 (water-cooled), KAWASAKI ZRX1100II, KAWASAKI ZRX1200S, KAWASAKI ZX-14R, KAWASAKI ZXR250R, KAWASAKI ZXR400R, KAWASAKI ZXR750R, KAWASAKI ZZR1100/ZX-11, KAWASAKI ESTRELLARSCustom, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA2 Helmet50RSL, KAWASAKI ER-4n, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI GPZ750R
You can get rid of the gnarliness.
I didn't like the squishy feel of Rubber on Normal step bar, so I replaced it with this Footpeg.
When I installed the return spring with the supplied reinforced return spring, it was too hard and the return movement was not smooth enough. However, the OEM spring hook on the bar side is longer than the OEM spring, so when the bar is folded to the full length of the footpeg plate, the hook interferes with the bar, causing a wound at the base of the bar, but it is not noticeable from a distance, so I did not mind.
I am satisfied with the moderate Edge Knurl Footpeg, which is easier to step on and less slippery.
View detail
Fits: SUZUKI GSF750, HONDA CB400SF vtec Revo, HONDA CB400SF vtec III, HONDA CB400SF vtec II, HONDA CB400SF vtec I, HONDA HORNET600, KAWASAKI ZEPHYR400χ, KAWASAKI ZRX400 II, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYR750, SUZUKI INAZUMA400, SUZUKI GSX400, YAMAHA XJR400R, YAMAHA XJR400S, YAMAHA XJR400, YAMAHA XSR700, HONDA HORNET250, HONDA VTR250 LD, HONDA VTR250, HONDA CB400SF verS
Separate handle for HORNET
Ordered last August, finally arrived this February.
HURRICANE Inc. has been quite busy.
It was worth holding out to buy from a pre-priced reseller.
The work was easy as long as the Handlebar holes were drilled.
The Curve is nice and easy to bend because of the forward lean.
I am wondering if I should extend the Fork and put it on the Top Bridge as it is a bit tight.
View detail
Same as OEM Product
Purchased due to lack of OEM Product.
The product is comparable to the OEM Product.
View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
I'm lighter
Clutch is now lighter.
Stainless mesh, so it seems to be durable.
View detail
Fits: YAMAHA XSR900, YAMAHA XSR700, YAMAHA MT-09, YAMAHA MT-09
Great bar
Well built handlebar. The welds look good and the chrome plating is very nice. More foreword and sporty grip angle but still very comfortable. Cool retro look too! View detail
soft
HURRICANESpiral Tube
Item Number ： HB6801W
Fits Cable Diameter Φ5-8mm
Total length 2.5m Color:Milk White
Soft and easy to use.
I use it wrapped around a SWAGE-LINEStainless Mesh/Brake Hose.
View detail
Diversion to CB250F
I installed a ZETA handlebar on my MC43, and it was about 30mm higher, but the OEM tension was too tight, so I replaced it with a ZETA handlebar. 1 pc of pull was applied to the handlebar, and the direct feel was increased by adjusting the play and the handle.:Pair (for Left and Right) I let it have play at full lock. View detail
Fits: YAMAHA XJR400, YAMAHA XJR400R, YAMAHA XJR400R II, YAMAHA XJR400S
Mesh
The mesh is durable and the Clutch is very light.
I would like to do this next time I replace it.
View detail
Fits: KAWASAKI ER-4n, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI GPZ750R, KAWASAKI Z1000 (water-cooled), KAWASAKI Z125 Pro, KAWASAKI Z250SL, KAWASAKI Z750 (water-cooled), KAWASAKI ZR-7/S, KAWASAKI ZRX1100, KAWASAKI ZRX1100II, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZRX400, KAWASAKI ZRX400II, KAWASAKI ZX-10, KAWASAKI ZX-12R, KAWASAKI ZX-14R, KAWASAKI ZX-9R, KAWASAKI ZXR250
Replaced from OEMfootpeg.
I installed it on my ZEPHYR400,χ. 。
ZEPHYRχ s OEM bar is approximately 9.7cm long from the Center of the hole to the tip of the bar 。
HF5132 is about 9.2cm from the Center of the hole to the tip of the bar, about 5mm shorter, but it doesn't bother me at all! 。
The upper part of the OEM footpeg is Material:Rubber, but this product is DuraluminCut-out. (Gold genus) So,
Material:Slightly more direct feel on foot than Rubber 。
I think the bar part is also very nice with the Knurl finish and not slippery. 。
This is my opinion, but I hope it is helpful.
View detail
A slight change in position, but it is effective.
Riding position can be changed without replacing the axel, clutch wire or brake hose.
That's a slight change, but it worked wonders for a Showa-era uncle's body type like mine!
In situations like UTurn, where the Handlebar is cut to the full, I thought it would be possible to operate naturally because the arms are not fully extended.
However, the handlebar replacement process itself is quite a hassle, so if you are not confident about it, it would be safer to ask a PRO to do it for you.
View detail
Fits: HONDA APE 100, HONDA APE 50, HONDA APE 50, HONDA MONKEY, HONDA MONKEY, Others
Semi-Up Handlebar Bar
[How is it used?
YamahaCHAPPY (CHAPPY) The OEMHandlebar of the "for replacement" was purchased for replacement because it was in Rust and looked like a mess.
I chose the Semi-up type because it was more expensive than the Up type and it looked like the wires would need to be replaced.
Was the one you received as per Image?
It was just like the picture.
Was the installation difficult?
It doesn't take much time to remove it from the Clamp and transplant the Switches.
The Left SideHandlebar Switch has a turnstile and requires drilling.
How was your experience with it?
Since the OEM is about 200mm up, the position is slightly lower than the OEM.
It does not affect driving in any particular way, but if you want to ride comfortably, OEM's 200mm or larger is recommended.
Style-wise, I prefer this Semi-up.
[Included Parts:were they on?
Handlebar only.
[Was there anything that disappointed you?
Not particularly
【Review】
This is a semiUp type handlebar that is just right for mini bikes.
Depending on the car model, it may be necessary to drill holes for the Handlebar Switch.
View detail
I like the name Parenthesis.
OEM→BEET→cafeOEM→Bundle replacement from BEET.
I have tried many things and found it to be the best fit! But there is one drawback.
The Clutch Cable interferes with the Meter at any angle. I bought a thin rubber mat at Encho and cured it for now.
If you want to avoid hitting the handlebar, the handlebar will be slightly gapped to the left of the center or raised up considerably. If I could re-drill the holes and adjust the switches, the range of adjustment would be wider. I am not sure if it is compatible with the Bikini cowl that I installed at the same time, but I am generally satisfied with it, so I will keep it as it is for the time being.
View detail
It can be installed with no problem if you have the tools.
As per your impresion, it takes a lot of time to remove the Screwwith Lock Bolt from the bottom.
Our procedure is to first remove the bolt that holds the clutch hose and brake hose to the body. The breaker bar is also large and sturdy. The Brake master and Clutch master can also be easily removed from the handlebar and placed on the body.
Once loosened somewhat, remove the 4 Bolts as the Ratchet of the FLEXHead can be easily turned afterwards.
Just float the Top Bridge and put the HURRICANE Spacer in between and put it back in place.
View detail
Good.
Easier and better rearward visibility. View detail
good value for money
Material of Type using K-FACTORY's OEM License Lamp:I purchased this Eliminator to replace my Stainless Steel Fender Eliminator, which has a Stainless Steel base plate, black chrome plated and clear coated finish. I am satisfied with it because it is less expensive than other manufacturer's Fender Eliminator. In my case, I replaced the blinker with a POSH one, so it took time to adjust the angle and position of the blinker.
Of course, the accuracy was also fine. However, it would have been better if the bolts on the base plate were black instead of stainless steel.
View detail
Large change in installation work
If you remove the handlebar cover of the scooter, a hole will be made there, and you just want to hide it.
I happened to have another job to replace the handlebar, so I worked on it in conjunction with that. In addition, there is nothing to hold the parts in place, so you have to use gold glue to fix the handles in place.
If you are not confident if you want to replace it, I suggest you ask Shop to do so.
View detail
Fits: KAWASAKI GPZ900R, KAWASAKI Z1000 (water-cooled), KAWASAKI Z125 PRO, KAWASAKI Z750 (water-cooled), KAWASAKI Z750 (water-cooled), KAWASAKI ZRX1100II, KAWASAKI ZRX1200S, KAWASAKI ZX-14R, KAWASAKI ZXR250R, KAWASAKI ZXR400R, KAWASAKI ZXR750R, KAWASAKI ZZR1100/ZX-11, KAWASAKI ESTRELLARSCustom, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA2 Helmet50RSL, KAWASAKI ER-4n, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI GPZ750R
The quality is very good.
2ValveZEPHYR.
Originally, the footpeg position is behind the footpeg, and Rear Sets are not necessary when riding on the thumb ball, but Normal step is.
Style-wise, it did not fit Separate Handlebars, so it was replaced.
The machining accuracy is high and there is no rattling, but I think it is a little short. ＋It would be better to have +10-15mm.
View detail
Fits: HONDA CB250R, HONDA CB125R, HONDA CB300R, HONDA CB150R
HURRICANE BMConti Type 3
With the NORMAL handlebar, my wrists were a little too far away from the handlebar, so my wrists were easily fatigued, but after replacing the handlebar, my riding posture became easier even in the middle of touring.
Quantity Handlebar:Pair (for Left and Right) The handlebar is slightly raised to prevent fingers from being pinched.
View detail
Mounted on st250eType in reverse orientation
[How is it used?
Installed on st250eType in reverse orientation.
Was the one you received as per Image?
As per Image
Was the installation difficult?
I asked Shop to do it for me, but I don't think it is difficult.
How was your experience with it?
The Style was very good, close to Separate handle.
View detail