Reviews
Fits: KAWASAKI VULCAN400 CLASSIC, KAWASAKI ESTRELLARS, KAWASAKI VULCAN400, YAMAHA DRAGSTAR400 CLASSIC, YAMAHA VIRAGO250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR400, YAMAHA DRAGSTAR1100Classic, YAMAHA TW225/E, YAMAHA DRAGSTAR1100, YAMAHA TW200/E, YAMAHA SR400/500, SUZUKI GRASS TRACKER BIGBOY, SUZUKI GRASS TRACKER, SUZUKI INTRUDER400Classic, KAWASAKI ESTRELLA, KAWASAKI W650, KAWASAKI W400, HONDA MAGNA50, KAWASAKI 250TR
It was defective.
After installation, the Fuse jumped when I checked the operation. I checked and found that the Bolt of the Blinker's Wiring Fix had contacted the Earth of the Horn and was shorted. I did not expect high quality because of the low price, but if you are going to sell them under the GarageT&F brand, you should at least check the operation of all of them before shipping, etc. I was disappointed when I installed it after processing and repairing it. View detail
You can't use the ZX-4RR in the up direction!
I used it to raise 2cm on ZX-4RR, but Link Rod length is 150mm, 10mm shorter than 25R, so it can't be used for raising direction. 25R is 160mm, so it can raise ±10mm=±2cm within 150mm~170mm range, but 4RR can only be used for lowering direction. Please note that 4RR can only be used in the downward direction! View detail
Fits: YAMAHA NMAX155, YAMAHA NMAX125, YAMAHA NMAX150, YAMAHA NMAX155, YAMAHA FORCE155, YAMAHA SMAX, YAMAHA MAJESTYS, YAMAHA NMAX125, SUZUKI ADDRESSV125, SUZUKI ADDRESS V100
Unfortunately, it didn't fit.
I purchased this product as a BirdCity155 compatible product, but it was necessary to modify the product in order to install the Left Side.
Unfortunately, we had to deal with a return, but the response was excellent.
View detail
Short cord
The cord was too short and it was no good. I forced it on and tried to run, but it might not have been attached to the Plug properly, but it gave me symptoms that I thought it might stall. View detail
Fits: YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP
parts shortage
There were no defects in the product.
However, parts were missing.
I think I am at fault for taking so long to open the order and for starting without NumberRinging all the parts. I ordered only Grommet today.
It is impossible to install until the part arrives, so it is not possible to put it on.
If you are considering purchasing, please make sure to check the part.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Product quality is the worst Level
After 5 months of ordering, it finally arrived and when I carefully unpacked it, it was covered in scratches. I am so disappointed. Don't they inspect the product before packing it.... It is a regrettable Manufacturer. I can't recommend them at all. View detail
Please don't sell this kind of product.
The package arrived today, but there are signs that the package has been opened and there is no instruction manual.
I couldn't tell if it was missing or not, and I couldn't install it.
I am having trouble figuring out what to do.
View detail
Fits: DUCATI SUPERSPORT 950, DUCATI MULTISTRADA V4 PIKES PEAK, DUCATI MULTISTRADA 1200 DVT PIKES PEAK, DUCATI MULTISTRADA 1200 DVT S, DUCATI SCRAMBLER 1100, DUCATI SCRAMBLER 1100 SPORT, DUCATI SCRAMBLER 1100 SPECIAL, DUCATI SCRAMBLER 1100 SPORT PRO, DUCATI SCRAMBLER 1100 PRO, DUCATI SCRAMBLER 1100 DARK PRO, DUCATI MULTISTRADA 1200 DVT, DUCATI MONSTER 937 PLUS, DUCATI MONSTER 937, DUCATI MONSTER 797, DUCATI SUPERSPORT 939, DUCATI HYPERMOTARD 950 SP, DUCATI HYPERMOTARD 950, DUCATI HYPERMOTARD 939, DUCATI DIAVEL 1260 S, DUCATI HYPERMOTARD 821
It's too wide.
It is so wide that when inserting and removing the STAND, you have to raise the body of the car considerably to get it on the ground. View detail
For Racer9.
I bought this to install on my Racer 9GT.
I couldn't put it on because it didn't fit.
I think you probably have the wrong car model for the Racer9.
View detail
It was a conformity guarantee, but ….
This is the first time I have purchased a Reinforced Ignition Coil that is guaranteed to fit, but as stated in the Title, the plug cord is too shorter than the OEM plug cord and cannot be installed as is.
Return it? Or replace the plug cord at your own discretion? You have to decide whether you want to return it or replace the plug cord by your own decision.
View detail
It's a shame because the quality is good.
The problem is on the Brake lever side, where the SensorSwitch that turns Cruise Control on and off is not pressed in enough to use Cruise Control. It is a pity because the quality is good. View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Large presence
Without much study, I decided to purchase Fender Eliminator, feeling that the higher the price, the better.
But now I don't like it because I see too many extra Frames.
My feeling is that Fender Eliminator must be Simple.
License Plate Light is also too Large and thick.
I can't change it to something different because it was too expensive.
View detail
I will never buy from them again.
I used it to disassemble the front fork of a scooter, but the tip broke off immediately. In the end, I used a thousand pieces of the same piece in a quantity of 1,000.:I bought 2pcs and managed to remove the C-ring. View detail
Fits: APRILIA SR 50 R (PIAGGIOEngine), APRILIA SR 50 FACTORY (PIAGGIOEngine) Model:Injector
of poor quality
I received it, but it is poorly made and has a lot of wounds. View detail
I wonder if there isn't...
Although there was no indication of the number of pieces, the quantity is the same as for other manufacturers.:I bought it thinking that 1 Set of 2pcs.
I would have bought OVER if I felt like I was losing money at this price& for 1pc.
It's a real shame.
Well, I placed an additional order.
View detail
Fits: SUZUKI GSX-R1000, KAWASAKI GPZ600R, YAMAHA FZ1, YAMAHA FZ1, YAMAHA FZ1FAZER, YAMAHA FZ1FAZER, YAMAHA FZ6-N, YAMAHA FZ6-S2FAZER, YAMAHA FZ6-SFAZER, YAMAHA FZS1000 FAZER, YAMAHA MT-01, YAMAHA XJR1300, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R1, YAMAHA YZF-R7
Gsx-r1000 17 to 21 years old is not hooked up to the Gsx-r1000!
Gsx-r1000 17 to 21 years old is not hooked up to the Gsx-r1000!
Correct the fit.
View detail
Fits: Others FCR Carburetor Body Carburetor for Φ28-Φ33(Small body)
The packaging is too messy for the shipping!
I thought the shipping cost was high for the parts, but since they are precision parts, I thought they were carefully packaged, but they sent the products in a Vinyl bag with no cushioning material and a single paper bag, which was a big surprise.
I can only hope that there are no deficiencies, but I am anxious and displeased.
The product may be trivial, but the buyer should be aware once again that he/she is paying a Gold for the product.
That's all
View detail
Not a Kit Part
Mounting Hardware is defective even though it is a Kit part.
Unable to install on current vehicle (ct125 CT110 HUNTER CUB)
Product Contents do not conform.
View detail
Addressv125Seat
The Seat I received is torn and I want to return it.
I had to delete the order screen when I received the item and
And that it's an unused number to call.
I could have emailed her, but she wanted a picture of me.
They said they shipped a torn Seat and if you want to return it, you have to pay in advance.
When you send a damaged item, you pay cash on delivery, right?
In the first place, it was not an expensive item, so I thought I would pay in advance.
It makes no sense because it would be an expensive product. 。
Why should our side have to go that far?
The system is difficult to return.
I still use this Shop only for buying OEM Parts.
View detail
Fits: YAMAHA SR250, SUZUKI 250SB, HONDA 250T LACustom, HONDA AX-1, HONDA CL135, HONDA CL350, HONDA CL72, HONDA CL77, HONDA CM250T, HONDA CM400T, HONDA CRM250AR, HONDA CRM250R, HONDA FTR223D, HONDA FTR250, HONDA GB250 CLUBMAN, HONDA GB400TT, HONDA GB500TT, HONDA MT250ELSINORE, HONDA MTX125R, HONDA MTX200R
Does not fit the KL250 Sherpa.
The Manufacturer's list of compatible models says it is compatible with KL250 Sherpa, but that's too long.
If installed normally, there will be excess
The quality of the product itself is not bad, so I think it will be fine for cars with longer forks.
KL250 Sherpa's Fork outerTop to bottom of trident is 240mm
Catalogue value WheelTravel is 230mm
100mm remains above the Outer even when shrunk the most without processing.
This would make Stroke about 130mm.
If it was just for Inner Tube protection purposes, it would be fine, but I don't think it is, so I cut it off, even though it will look very ugly lol.
In hindsight, I lightly regret that using the top half wouldn't have made it so ugly.
However, even in this state, the Stroke will be reduced by about 50mm
Boots itself becomes Bump rubber.
Even other companies' products that say they are compatible with KL250 Sherpa are quite long.
Would it be better to just use a shorter product with more extension?
Maybe I'm losing my mind, but I'd like to find a good product!
I bought it + even processed it so I'll be using it for a while lol.
View detail