Reviews
Fits: その他
Just changing it changes the atmosphere.
V56 on the Red Yes Reflector. [Color] Changed to Smoke.
Phillips Screwdriver1 pc was used for the replacement and the atmosphere changed dramatically, giving a tighter impression.
I am glad I replaced it.
View detail
Reflector
I wish it had been Bolt On. View detail
Not luxurious, but works fine.
tawdry A "normal with Reflector's Number stand. A few more details to be worked out.
I was happy if the design was solid and good looking.
View detail
Baptized Design!
I think it's a pretty cool design! Vibration proof and single cylinder Motorcycle
But it doesn't sound scared, so it's RECOMMENDATION!!!
View detail
Easy installation
Bracket and Bolts required for installation
It was ready to go and installation was completed immediately.
View detail
Installed together with SEROW250 DRCFender Eliminator.
The Fender Eliminator Kit from DRC was installed on the SEROW250 to eliminate the reflector.
It would be Sporty without it, but since it is a Rule, it must be installed. Without it, it will be treated as poor maintenance.
The KIJIMA License Plate Base is installed in the back, but it could be installed with the existing bolt.
View detail
Cool, easy to install, highly recommended!
I bought this kit at the same time I installed the Fender Eliminator Kit on my Grom jc75, and it is simple and cool. I was not happy with the 1cm gap between the License Plate and the Reflector, so I had to modify it to fit the gap. It is good to use the ready-made one as it is, but I like to fine-tune it and make it more to my liking. I can recommend this product. View detail
Reflector angle needed to be adjusted
It is made to fit the TitaniumPlateHolder made by k-factory, so the fit is Exactly.
However, the angle of the reflector after installation was such that it was worshipped at the bottom. (Since the License Plate is co-tightened, the angle is naturally determined by the License Plate angle on the body side.) 。
After much consideration, the angle of the Bracket in question is angled. (Folded part) The angle was adjusted by tapping the Finally, the angle was just right.
Also, the part where the reflector attaches (Bracket part) I also thought that the bracket could be hidden when a slim-type reflector is installed if the dimensions of the "1" were made a little smaller.
I have diverted the OEMReflector so the Bracket is hidden and not visible.
View detail
active reflector kit
Hello cb400sf The pure rear fender was plain So I found it I bought two active and Kijima products I think active products are good because they have LED lights It was a bit complicated when I installed it But it's neat and beautiful Thank you. View detail
Satisfied with the new look and feel
I was looking for a round mirror that could be attached to the bolt of the Right Side Opposite Thread Screw without an adapter, but I couldn't find anything like it, so I decided to purchase this product's Mirror Bracket and Fixing Bolt in quantity.:Pair (for Left and Right) Purchased at Rose.
Quantity:This is because there was no Round Type Opposite Thread ScrewSpec. available for sale as a Set (there is a Normal Thread Screw with security parts). (Normal Thread Screws with security parts are available)
I have not driven the car after installation, but I don't think I will be bothered by the slight shaking that occurs when the engine is revved up.
The Mirror part can be moved to some extent (30 degrees in all directions according to the manufacturer) even after it is fixed, making it convenient for fine adjustment.
Although a smaller Mirror would have been ideal, the Mirror's area meets safety standards.
It is a little harder to see directly behind the Mirror than the previous horizontal Mirror, but this may be adjustable by extending the Mirror section more to the tip of the Bracket. However, once fixed in place with the imonesi, that part of the Bracket can be " and marks, so it is better not to move around too much.
I used a spring washer to prevent loosening during installation.
At first, I used the ring on the base, but it was too loose, so I decided to use only the spring washer.
View detail
Perhaps this is the only choice.
Used for YOSHIMURA's GARBON License Plate Holder.
I was using an Active Fender Eliminator with a Daytona reflector, but the PlateHolder was too long for the Daytona reflector, so I switched to an Active Reflector with long mounting holes. It fits perfectly and is very good.
View detail
a legal requirement
I ordered it with a fender kit because there should be a reflector around the license plate. It fits perfectly because it's from the same brand. View detail
buying the same item multiple times, each one being a different color (colour)
[How is it used?
I bought the Fender Eliminator Kit from Active to go along with it!
Was the one you received as per Image?
As you can see in the Image, it is neither good nor bad.
Was the installation difficult?
Very easy to install
How was your experience with it?
The Reflector is performing its function well.
I think it is good because it is not too large.
View detail
this one option
I think it is the coolest of all Reflector products.
I always buy a Fender Eliminator when I have one.
View detail
Reflector
I changed from a round reflector to a Slim reflector. View detail
Fender EliminatorSpec.
This time Quantity:2pc. I bought the Set for the second time, and I bought it again because it was so good last time. View detail
At the same time as the Fender Eliminator
I think it is the thinnest.
This will be the one that does not stand out the most.
Easy to install, just insert it into the Number.
Two 10mm Wrench will be sufficient for installation.
View detail
Fender Eliminator and Reflector installation.
From Motorcycle shop to GORILLA which has been a Fender Eliminator since purchase. I don't see a Reflector or a △Mark. I installed the Number using this kit, which is co-tightened with the NumberNut, and the Reflector is attached to the hole at the bottom of the Number to complete the installation. It was very easy. (You can also install the △Mark (sold separately) under the Reflector, but I will post my impressions of that in another post. My GORILLA has extended Swing Arm with Down Suspension, so it may interfere with Tire …. (So far it is Large sturdy.) It is a horizontal Reflector, which is fine in terms of area, but I am a little concerned about visibility. I like the fact that it looks Simple. View detail
To MONKEY125Rear.
The KITACO product is well made, and the KITACO mark is subtly placed in the middle of the reflector, which is nice. View detail
unconcernedly
I was looking for a reflector that was less assertive, and this was just what I was looking for. View detail