Reviews
Change of position
Used to change the position of the Rear Sets.
You can choose the Size, which is useful for repositioning.
View detail
Center out.
[How is it used?
I bought an external wheel from Spare, but the brake disc did not fit in the center of the Caliper, so I used this Spacer to adjust the center.
At first I tried to recreate the Wheel color, but it was a pain in the ass, so …
Was the one you received as per Image?
As per Image
It's a beautiful finish.
Was the installation difficult?
Simply insert it between Caliper and Caliper support.
How was your experience with it?
The disc is now in the middle of Exactly.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
They have spacers of various thicknesses and sizes, which is helpful for Privater.
View detail
I'm pretty sure it will be transmitted to Direct.
[How is it used?
Easy to understand when driving through mountain passes
Was the one you received as per Image?
Street Image
Was the installation difficult?
It was easy to replace, just loosen the fixing screw under the Handlebar Mounting.
How was your experience with it?
Front vibration is transmitted to Direct
[Included Parts:were they on?
Instruction Manual was available.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Request I think it will sell well if you release Red and Blue as well.
View detail
Even if there is a large rattle, the gap is much smaller than you think.
I bought the 0.3mm Clutch lever as a repair for the Clutch lever that had become completely rickety after years of use.
The Clutch Lever pivot is always diminishing, and even if you replace the lever, the lever will not rattle as much as you think if the lever holder is worn out, but just adding this Shim will solve the problem!
So, it's not so easy to make recommendations to everyone.
That's because even the thinnest 0.3mm would normally be difficult to insert.
I used 0.3mm at the Lever tip with nearly 20mm of up and down wobble, but even with such a loud wobble, 0.3mm is Limit.
Quantity 0.3mm on top and bottom of Lever pivot before purchase:I was going to insert 1pc. at a time, but it was impossible to insert 2pcs.
In the end, it was all I could do to put one in the bottom side of the lever, which would be the easiest to reduce.
However, if Quantity:With just 1pc. of the new product, the Lever's rattle has been dramatically improved, resulting in smooth Lever operation and no rattling, just like new.
This is not a solution for everything, but it is a recommendation for those who cannot get rid of the rattle even after replacing the lever (i.e., the lever holder is decreasing).
If I had the time, I would dare to cut down the LeverBody from the new car and put a Washer above and below each Pivot.
This way, the Lever Body's aluminum and Lever Holder's aluminum won't come in contact with each other, and the Lever Feel can be maintained for a long time if it's well greased up.
View detail
Useful for adjusting the length of Screw.
I like the fact that Spacer comes in Gold! View detail
Fits: KAWASAKI Ninja250, SUZUKI GSX250R, KAWASAKI Z900RS CAFE, KAWASAKI Ninja400, KAWASAKI Z900RS
Necessary for NINJA2 Helmet50R /400
To install POSH Faith's Stand Hook on NINJA2 Helmet 50R /400 (2018-)
You will definitely need this Spacer, so buy it together!
View detail
Substitute for RearCarrier color.
I used this product due to the relocation of the rear blinker.
The size of the bracket is very good.
View detail
It is used for Blinker installation.
I used this product due to the relocation of the rear blinker.
I chose Red and it's a good color.
View detail
To fill in a small gap.
It is a beautiful and inexpensive way to buy a light. View detail
It is also a companion for Carbon parts installation.
The M8→M6Size of this product is often used in the tightening section of Other Brand ProductCarbon.
Carbon parts can break if over-tightened, and this is often clearly stated in the Instruction Manual when purchasing Other Brand Products.
However, most of them have a hole for M6 Bolt and are designed to be tightened with M6 Bolt.
Even if you are a friendly manufacturer, you will only get a resin washer.
Torque regulation for expensive carbon parts (About 10N-m at M6) I'm a little scared to put the …
This product is useful in such cases.
If the hole on the Carbon parts side is lightly exposed with TaperReamer etc. and slightly enlarged, this product will be able to pass through, and the axial force will be received by this collar.
The shaft part is a little long, but it can be dealt with by shaving it with Oil stone or bulking it up with M8 resin Washer.
Personally, I prefer the latter.
KITACO also sells similar parts, but the size is different from KITACO.:Aluminum.
It is also expensive here for Material.
(KITACO part number:K-CON 0900-093-09006)
Personally, I use this one because I don't like rust.
So, besides the original purpose of M8→M6 conversion, it is also a useful Parts.
We recommend you to purchase Carbon parts and other external parts when you purchase.
View detail
Replace Rusty Spacer with Aluminum spacer
When I was replacing the bolt on the Exhaust Bracket that holds the Swing Arm and Exhaust System, I found rust on the Spacer that goes between the two, and I was looking for some good repair parts. I was looking for some good repair parts and found this Spacer. View detail
ReassuranceManufacturer KITACO Color
I bought a used Slash guard for XJR400R, but it didn't have the attached color etc., so I used this one instead.
The color of the product is also Black, so it does not stand out strangely, and I am very satisfied because it is made carefully and inexpensively. I think that it can be used in various places because the size is also abundant.
View detail
Convenient colors
I bought a used Slash guard for XJR400R, but it didn't have the attached color etc., so I used this one instead.
I really wanted to get the 60mm color, but none of the manufacturers were offering it, so I got the 30mm×Quantity:2pc. I substituted this product in Set.
The color of the product is also Black, so it does not stand out strangely, and I am very satisfied because it is made carefully and is inexpensive.
View detail
Black on yellow beauty.
The black washers on yellow rank look great. The fit and finish is perfect. The price is steep but once you see the quality and looks you will be happy! View detail
Spacer。
Used as Spacer for License Plate. I am satisfied. View detail
RequiredParts.
I bought this because I didn't want to stack my Washer. It looks great and Refreshing. View detail
To secure Space.
This is a very useful Parts and it is very helpful. View detail
Satisfied
This is a necessity for securing the skimmer and Space you care about. View detail
To the skimmer.
This is the kind of Parts that can reach the itchy spot. View detail
Used for Cowl fastening points
[How is it used?
Used at the fastening point of Under Cowl.
How was your experience with it?
This Rubber Collar is placed between the collar and the part that is fastened with Bolt to fix the Cowl.
Cowl's Wobble will be suppressed.
It's easy to get at the supply store and is very helpful.
View detail