Reviews
Used for insulation of Fuel Tank
Temperature also rises to protect Gasoline from the heat of Engine
Heat insulated using this product on the back of Fuel Tank.
It is wrapped in a roll and easy to cut to your favorite Size
There is no problem with adhesive strength.
In bad products it may be scratchy with Glass fiber,
This product is excellent in workability without Glass fiber Rose.
View detail
Thermal insulation tape
When installing the outside RightAir Scoop outside the buell, the intake manifold comes very close to the position, so I bought this product for the prevention of Scoop's dissolution.
Easy to handle, easy to cut with scissors in any shape, you can stick to small places.
It was affixed to Scoop a little Large, I confirmed the engine start condition, but there was no change in shape, securely insulated Scoop and insulated.
I think that it is exactly good for the protection of Under Cowl by the heat from the intake manifold such as SS.
View detail
Insulation Mat
Since buell is a V-type 2-cylinder Engine, hot air from Rear bank is caught under Seat, Seat is very hot and sitting is painful and I was thinking about something..
After finding this product which we are watching a lot and evenly sticking it under Seat, I felt almost no heat, became very comfortable and became able to concentrate on driving.
I really bought it!
View detail
Thermal insulation tape
Due to the heat from the Engine's Rear bank, the Rear seat got very hot, lacking comfort and buying it for countermeasures.
Just stick it to the Reverse side of Seat, it can be installed very easily, it can be easily cut with scissors so it is easy to match any shape.
When I pasted it, the heat can be reduced considerably and I am very satisfied..
View detail
Insulation Mat
Buell is getting hot as the Frame burns because the Exhaust System from the Rear bank's Engine is passing through the Frame and buying for countermeasures.
When installed in the proximity of the Exhaust System of FrameReverse side, the temperature dropped to warm place from hot, and very good result was obtained.
Those who are thinking about how to handle the heat of Frame, I wonder if it is included in the choice.
View detail
Engine protection from heat
【What made you decide the purchase?】
Since we installed resin tank, we bought it for heat resistant processing.
【How was it actually used?】
Engine heat, fuel Pump breakdown and Gasoline could be used without boiling.
Because we are using Glass Wool for Cut, it is attentive as it gets scratchy when you get to your skin.
【Was it difficult to install? (Hard parts case)】
Work was easy, because Double-sided Tape is on the back.
[Is there anything I was disappointed about?]
There is none
【Hope for Manufacturer - Please let me know if you have any improvement points]
There is none
【Have you compared items?】
There is none
View detail
At such times, Posh is reliable.
I was looking for Heat Insulating Material when exterior of Exhaust System side of DR-Z 400SM was exchanged.
Of course OEM is also good, but consider buying here that it takes time to delivery.
Packaging is frugal, quality is top notch.
You do not have to over-pack it.
What about this Tape?
- Cut to your preferred length
- Since adhesion is not too strong, it is rare to fail
- Moderate Length
- Being able to use it other than exterior
Is this?.
It is nice to be cheap, but if quality is not good it will not be used.
I do not want it when the exterior melts..
On that point, if usability at this price is good, it is 1 pc. I regret that I should buy it (Lol)
View detail
Scooter's Helmet inSpace's thermal barrier
I used it for heat shield of Helmet inSpace of Addressv125.
Remove Helmet in, paste from the outside.
The product came in one winding state.
I cut it to an appropriate length and pasted it.
I thought that Aluminum Tape says that it would be hard to stick to a place where it was bent..
When I started pasting, I felt that workability was very good because it was stuck to the curved surface unexpectedly and flexibly.
I thought that it could be used in various places depending on how it was used.
The price was affordable, so I thought that COSPA is a good product.
View detail
VFR750F (RC24) I used it for. It is preeminently good.
For V type Engine Rear bank or Seat "warm" Especially in summer "Hot and uncomfortable" is.
Also, seat sponge seems to heat up, so once it gets hot it will not cool down easily.
I thought I should try making a shielding plate, but I thought that it was a simpler way and I bought it.
Pasting itself is simple because the whole is in the shape of a tape.
Just when the part of the edge is left uncut, the insulation Wool in the inside seems to slacken.
I handle with Gum Tape and I do not have any problem with Large.
In terms of performance "warm" It becomes only to degree "Large satisfaction" is.
Well, I think I will not use it for purposes, but it seems a bit NG to the visible part.
View detail
It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an indi
It purchased to use it for the interference portions of the Silencer of a Muffler, and a Undercowl.Since the product of
other company seemed to be large and seemed to be user-unfriendly, I think that this article of a moderate size is good for an individual user.While using it about
engine performance, he would like to discern, but since there are not necessarily so various kinds, even if somewhat powerless, I think that the width of selection is narrow.
View detail
It was used for the sheet flesh side for the measure against heat. Since there is a certain amount of thin elasticity, it is easy to stick also on a curved portion.The heat of hips decreased certainly.Although I think that fuel-tank flesh sid
It was used for the sheet flesh side for the measure against heat.
Since there is a certain amount of thin elasticity, it is easy to stick also on a curved portion.The heat of
hips decreased certainly.Although I think that
fuel-tank flesh side has an easy-to-use Seat type, it is the best for the measure against heat of a fine portion.
View detail
It sticks on the flesh side of the Tank of CB400SF, and made engine heat not get across to the body.Even all fragments fine in area were used, and most Tank flesh sides have been covered.The heat insulation effect was found clearly.Although it is sti
It sticks on the flesh side of the Tank of CB400SF, and made engine heat not get across to the body.Even all fragments fine in
area were used, and most Tank flesh sides have been covered.The heat insulation effect was found clearly.Although it is still hot in summer, is it better until now?Although it is likely to become impossible to feel warmth in the winter of
, it is satisfied with the heat insulation effect.
View detail
Although he plans to stick on a Cowl and being purchased, it did not become shielded state but the purchase of double-stick tape was required separately.Since wire was attached, originally I think the thing used winding around a Chamber.
Although he plans to stick on a Cowl and being purchased, it did not become shielded state but the purchase of double-stick tape was required separately.Since wire was attached, originally I think the thing used winding around a Chamber. View detail
It purchases again as a measure against heat of a Regulator. This is a gadget from which attachment places, such as a part which were dramatically convenient, and curved or curved, are not chosen.This use part was used for the measure against heat of
It purchases again as a measure against heat of a Regulator.
This is a gadget from which attachment places, such as a part which were dramatically convenient, and curved or curved, are not chosen.This use part was used for the measure against heat of the Regulator attached just in front of the Engine.There were only only 3 cm of crevices between an Engine and a Regulator, since there was an example which a Regulator gets burned and damages with engine heat well, the thin griddle of the Aluminum was purchased in advance, the heat-resistant Tape was stuck on this, and preventive measures were carried out.It is used, there is almost no propagation of heat measure before, and it obtained the result which is protecting the Regulator from the engine heat under the blazing heat of midsummer.He is very Satoru Taisho.We recommend you to cope with the direction of Buell riding on this heat-resistant Tape by all means.
View detail
[Webike Monitor] Since the sheet was hot, it stuck on the back side. if it runs for 2 hours although the sheet becomes difficult to get hot -- -- it is ineffective. I thought whether it was Massey whether it is the lay which is not.
[Webike Monitor] Since the
sheet was hot, it stuck on the back side.
if it runs for 2 hours although the
sheet becomes difficult to get hot --
-- it is ineffective.
I thought whether it was Massey whether it is the lay which is not.
View detail
Since the Polyethylene tank of the external article was also changed into the flume Big tank, it stuck on the measure against heat. Although high speed operation / traffic congestion way was run about 160 km in 30 air temperature, I think whether to
Since the Polyethylene tank of the external article was also changed into the flume Big tank, it stuck on the measure against heat.
Although high speed operation / traffic congestion way was run about 160 km in 30
air temperature, I think whether to be the engine performance which may be trusted, since there was also no problem in particular.
It may be safer to keep away from dress with a Vinyl sheet etc. at the time of
, in addition processing.
It is .... itchy in case of work (carrying out itself is Allais!) with the
short-sleeve undershirt.
View detail
Since he can buy a 3-m thing around 1000 yen by the almost same engine performance in a Home center .... However, the ease of removing of pasteboard was excellent in this one (smile).
Since he can buy a 3-m thing around 1000 yen by the almost same engine performance in a Home center ....
However, the ease of removing of pasteboard was excellent in this one (smile).
View detail
Under the sheet, since having got on by heat was becoming difficult with engine heat to a Frame, it purchased for the measure. In the bottom of the sheet, direct attachment and a Frame stuck this Tape directly under the sheet at the Frame inner side.
Under the sheet, since having got on by heat was becoming difficult with engine heat to a Frame, it purchased for the measure.
In the bottom of the
sheet, direct attachment and a Frame stuck this Tape directly under the sheet at the Frame inner side.
Engine heat was able to be prevented to some extent as expected [
].
-> hot as
touch -- since it is a warm kana grade, it is dramatically satisfactory.
This Tape sticks to the form stuck since there is flattery nature finely.
I think that it sticks on various places and can do since there is also quite a many Tape capacity.
In the direction troubled by
heat, it is very recommended.
View detail
It stuck on the portion which is likely to be damaged by heat around a Silencer. Although the direction of the effect is an unknown, I feel that it can ride in comfort for it. Or [ that it may not use since the price is also cheap, or I may have
It stuck on the portion which is likely to be damaged by heat around a Silencer.
Although the direction of the
effect is an unknown, I feel that it can ride in comfort for it.
Or [ that it may not use since the
price is also cheap, or I may have one sheet ].
View detail
It is used for the Undercowl of RS125 in the measure against heat. The Cowl which got quite hot after the neighborhood run from the Chamber became less hot at all. Degradation by heat is also prevented now.
It is used for the Undercowl of RS125 in the measure against heat.
The Cowl which got quite hot after the neighborhood run from the
Chamber became less hot at all.
Degradation by heat is also prevented now.
View detail