Reviews
sufficient for one's needs
Used for Caliper's Overhaul.
Ordinary. It's a normal Washer, but you should buy it because you don't have to be stingy with these kinds of supplies around Brake.
1 bagQuantity:1 Set of 2pcs. equals 1pc. of Banjo bolt, you will need to buy the required number of pieces to replace the hose itself.
Also, the price is a bit high, but if you're going to take the brake hose off every day, it won't be a problem if it's just an occasional maintenance.
View detail
BrakeMaintenance
I bought this for Brake Caliper Maintenance and Overhaul.
It works normally
A lower price would have helped.
View detail
I'm doing my job reasonably well.
The one currently in use leaked oil, so I decided that a distortion of the body had occurred because the leak did not stop even though I replaced Seal, so I purchased it for renewal.
The performance of the OEM parts is very different from that of the OEM parts, because the OEM parts did not stop at the high speed corner approach at Izu Skyline. After the change, the same Breaking Point can be used for the approach with no worries.
This product can be installed with confidence because it is crushed during installation by the short parts that support its performance.
View detail
For Master Cylinder.
I overhauled the Master Cylinder, so I'm forced to replace it! LOL!
It seems a bit pricey, but the Brake is life-threatening, so I try to replace it with a new one every time I take it off.
View detail
Brembo for Brembo.
I bought it to replace the Caliper.
Probably another Gasket would be no problem, but because it was a replacement for the Brembo caliper Banjo bolt, because it was not an expensive one, I chose the Gasket that Brembo puts out for the Brembo.
View detail
Okay!
I replaced it while I was at CaliperOverhaul!
It's not too bad, not too bad, but it's normal.
If I ever need it again, I'll buy it!
View detail
It's the same brand of brake hose, so get it together
I bought the Swage line Brake hose, so I bought the same for Washer, just in case We have them all at Brand
It was a Stainless Hose, so I thought it was the non-aluminum Copper I chose Washer
I braked with Circuit, but of course it doesn't leak, and there is no problem None
View detail
Take a spare stock and replace it at maintenance
Since it is not reusable, you can keep it in stock for maintenance and spec. changes Replace it with
I want to use it properly because there are aluminum and copper material
View detail
We could use it
The inside diameter is the same, so it seems to work
The following sizes ( ) are Honda OEM Products
Inside diameter:10.0?-(10.0mm)
Outer diameter:14.0?-(14.9?-)
Thickness:1.0? (1.4?)
An unlikely size for a home center
I bought it because the price is less than half the price of the OEM Product
Two cards in one place, 0.8? difference
Crash washer, so the difference will be a little smaller
I'm going to check the position of the holes in the Bolt before using it just to be sure
Large Hand Mail Order Site for even less at 10 per lot, but this one is even cheaper at Quantity:Available from 1pc
View detail
When I remembered
It's not a consumable item, but for some reason I use it often, so I buy it when I remember
In the GSX1300R, the first time around [Color] I went from ClearMesh to Black the second time I replaced it
Even then, I think it's 9 cards in Brake and Clutch?
Quantity in a Rear:1 Set of 4pcs.…。
When I made KLX and CRF also a colored Brake line, … or
Master Cylinder's Overhaul or …
I'm going to have to use it for something, like when I'm organizing I'm gonna go buy some more Like … 。
View detail
Good stuff
I used it for GORILLA's external Front DiscCaliperHose washer
I used it when I changed the brake fluid and the drain bolt when I changed the engine oil I change the washer once every two times, but when I change the brake fluid, I make sure to do it once every time It's just right for the quantity, because it's an exchange, and the feeling of using it is tightening up It's very comfortable and the Pushing of the Torque wrench's tightening sound is very good It feels good
View detail
![3/8"/10MM BANJO WASHER [DS-097014]](https://global.webike-cdn.net/photo/impression/04/04115eb71ed8078422ccd79115b8d1d7L.jpg)
Cheap and satisfying
I bought this to overhaul my Plaque-Caliper I thought about it, but it was cheaper, so I bought it I think I use the Product, but if I'm going to maintain it myself, I think the cheaper one is better and buy it I did View detail
OEM equivalent
Motorcycle front brake overhaul and brake hose I had to remove it, I have purchased and exchanged it this time, previously it was a Quantity:I bought 1 Set of 3pcs. and if you tighten it up with the right torque, there is no oil leakage We have a Rear brakeOverhaul planned for the future Quantity:I purchased 1 Set of 10pcs I am very happy with it I think it's a good idea to stock it View detail
I've only used the Swage line
I try to keep some stock on hand because it's something I always replace when I remove the Hose etc I've only used the Swage line, so I don't know if it's good or bad, but I've had problems with it I have never done this before View detail
Fits: HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100, HONDA NSF100, HONDA XR100 Motard, HONDA Ape 100
Large odd, satisfying Parts
I could use an alternative, but I think it's actually a proprietary product, the M10 Aluminum Gasket I used another diverted product, but its thickness was too thick and caused oil leakage And the Oil leak is gone View detail
BrakeMaintenance essentials
I used it on a BrakeOverhaul with external brake hose I thought about using it, but it was already with stages, so I changed it to this product Because the nipple of the brake hose was the one of anodized aluminum, I changed it to this product Gasket is also Material:I selected Aluminum There is no leakage of oil after the installation, and it has no problem in terms of functionality It is View detail
Battle at price
Takekawa Oil cooler's Oil takeout Oil seems to blur from Valve and it leaked even if we tightened it, so we thought about buying KITACO's Oil cooler but if you replace Washer before that I tried to replace it with a regulation Torque firmly tighten it and make it move Large Succeeded! I went to the Touring over 350 km on the next day, but thanks to no bleeding Oil cooler fee Since it floated, other parts can be purchased.
View detail
It is as expected.
Brake hose from NORMAL to DAYTONA product
I bought it together as it was replaced.
For personal tastes, copper is the better one than Aluminum.
View detail
only this one.
I used it for hydraulic clutch of ZEPHYR 1100. I got to this by saying Aluminum in the place of Aluminum. It's cheap and relieved. Let's change it to a new one. View detail
Thank you Cospa best
I dropped Caliper for the first time in several years and I did it. I will remove Banjo bolt
This Washer that can not be reused must be a brand new.
Although it looks unlikely to be more reliable than OEM Product, it seems reliable, so I think that it is very good in terms of price and number of copies. By the way, thinking about safety, I think that it is best to close this part with Torque wrench.
View detail