Reviews
HURRICANE, are you serious?
[How is it used?
I purchased this product to prevent Trouble such as rust by plugging the hole in the Cap bolt.
Was the one you received as per Image?
When I picked up the product, my impression was that it would be easy to install by simply inserting it into the hole. Until this time, .....
Was the installation difficult?
As it turns out, it cannot be installed!
The depth of the hole in the cap bolt is 3mm, but the length of the hole plug (the part that fits in the hole) is 4.5mm! I was going to install it on my FZS600, but I suspected that the cap bolt used on Yamaha cars is special, so I decided to install it on another Motorcycle I own, KawasakiD Tracker, SEA BASSRGV250, and SEA BASS RGV250, and I was not sure if the cap bolt used on Yamaha cars is special or not. I tried with the bolt used in the MOTO GUZZIV11LE MANS, but I still couldn't install them all!
How was your experience with it?
3 Pack total 1Quantity:2pc. After much consideration, I decided to shorten the length of the set and use it. However, if I cut it down, the two stoppers attached to the lower part of the neck would be lost, and if I simply set it in the hole, the Hole Plug would fly away due to vibration and wind pressure. The decision was made to adhere them together using the This bond is flexible even after curing, so the Hole Plug can be removed later.
I first thought about doing the shortening process manually, but the quirkiness 1Quantity:2pc. I used my Belt Thunder power tool because I had a GSX400E to do the set as well. With this tool, it is easy to shave in an instant. But I had to be careful not to shave too much.
[Included Parts:were they on?
There is no such thing.
[Was there anything that disappointed you?
It's super disappointing because it's useless as it is!
Other items that would be helpful
Opinion or request to Manufacturer:Mr. HURRICANE, if you sell products like this, you will lose credibility!
View detail
Rust prevention by preventing water accumulation in the recessed part of the bolt
[How is it used?
When it rains, water collects in the recess of the cap bolt, so I decided to cover it before it rusts.
Was the one you received as per Image?
It was just like Image.
Was the installation difficult?
Installation was super easy. I was rather careful to take it out of the package so as not to drop it.
I degreased the Bolt recess with Parts cleaner before installing it in the Bolt recess.
In order to prevent it from falling off, I applied a thin layer of Grip bond to the O-ring part of the shockproof Gel from DAYTONA that I happened to have.
How was your experience with it?
Works as per Image. It hasn't come off so far.
I chose the same black color as the Handlebar Post so it doesn't look out of place.
[Included Parts:were they on?
No. O-ring is already installed.
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
It is better to degrease the recesses of the Point and hang/Bolt before installation to prevent them from falling off naturally.
Items to buy together/You don't need to buy it, but if you have Sealant or Liquid Gasket, you should apply it to the O-ring part and install it to prevent it from falling off naturally.
View detail
Fits: KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000 (air-cooled), KAWASAKI Z900 (KZ900), KAWASAKI Z750 (air-cooled), KAWASAKI Z2 (750RS/Z750FOUR), KAWASAKI Z1 (900SUPER4)
To KICKless.
The Rear Sets and Kick pedal interfere with each other, so I removed the Kick pedal and installed this Cap.
I like it because it matches the overall Image of the vehicle.
It may not be suitable for a NORMAL-looking car body.
View detail
Glam up your Cap bolt
What made you decide to buy?
I purchased this product for the purpose of dress-up around OEMAttachment and Engine Guard.
How was your experience with it?
The appearance of the Engine area has changed a little. Probably, others will not notice if I don't tell them, but I am satisfied with myself.
This is the part you want to check before driving to make sure it won't come off due to vibration.
[Regarding installation]
Installation is easy, just insert it into the head of the Engine GuardMounting Bolt. However, when I bought it, it was difficult to insert into the Bolt, so I used a little silicon spray on the ORing and installed it.
View detail
I installed it to Bolt of Tandem Footpeg.
I bought this to give my tasteless Bolt head a little Custom.
Because it is a Black Bolt and a Black Cap, it is difficult to understand it when seen from others, but
He is satisfied with Large, so it is good.
View detail
For Dress-up
Suitable for Cap bolt in various places.
There is a stopper on the product so you don't have to worry about it coming off.
I wish it was a little cheaper…
View detail
Purchased to prevent rain puddle on Cap bolt.
I bought this to prevent rain and car wash water from collecting on the Cap bolt that faces the sky.
Installation is good by fitting and lightly tapping with a rubber hammer.
View detail
It's just a plastic Cap.
It's just a plastic cap, like the title says.
It is probably the same model as the one included in the HURRICANE Pipe Handlebar KIT in Black.
This time I used it on a Bolt that was dyed black on Stainless Steel, but it was too tight!
I accidentally got a Wound on the butt of a Penetrating Minus.
View detail
Dress-up made easy
I bought this as a Cap for Fixing MirrorBolt.
I'm glad I put it on because every time it rains, the hexagonal hole part used to be a puddle of water.
Installation is also super easy, just lightly hammer in with a plastic hammer etc.
View detail
Cap bolt Cover
The Wrench hole in the Cap bolt is bothering me so I installed it as well as the Dress-up.
The color is Black, so it looks nice and tight.
View detail
It's cheap and it looks good.
I used it to improve the appearance of the cap bolt around the handlebar.
As you can see in the picture, the color matches the Titaniumium color of Posh's NASA TypeCap cover.
It's useful because you can almost hide the Bolt with both of them.
Just one note on installation.
Material:There is a cut-off from the RUNNER 125 at Plastic, so make sure it is on the lower side, where it is less noticeable.
View detail
Bolt cover
Looks good to me.
But if you do one place, you might want to align other places too…
View detail
Cap of M6 Bolt
M6 Bolt's Cap. unlikely.
I was using Silver, but I had no problem with durability, so I bought Black.
I used it for my Bolt on Clutch cover.
I am satisfied
View detail
To prevent rust.
MirrorMounting Bolt tightening holes
There was a pool of water and Rust.
I bought a Cap!
There was one with and without a rubber at the end of the cap, but
The part to be used this time is the Bolt that attaches to the horizontal direction
So, is it Large sturdy without Rubber? I think so.
Does the size fit since it's a special bolt?
I was worried, but the Exactly/Fit
This way, there's no water pooling in the car wash or rain.
It won't rust and is safe.
Quantity needed:2pc. Against the Set
Quantity:1 Set of 4pcs.:2pc. The Set becomes a spare part.
It was a waste of time to find a usable part of the
I couldn't find anything.
Quantity:1 Set of 2pcs. products would also be available.
Thank you.
View detail
Black chrome?
It is Black chrome, but it is not so black as almost Chrome image.
If you ask me. Is it a little Black? That's about it
Cap bolt's inner hexagon with Exactly Uniqlo plating is transformed into a high-grade bolt
Don't make a mistake as it's not something you can put in the Screw hole! I made a mistake, W.
Is it a bit high? Maybe you could get 10 for 1,000 yen?
View detail
Ideal for covering up holes, but difficult to remove.
It is used for the screw hole of Plate which is exposed with footpeg position change. Because this is much cheaper than hiding with an ordinary Bolt, and the appearance seems to be good, I tried it.
The diameter of the head is almost the same as the screw hole and it is very neat. The protrusion on the side goes in easily in the inserting direction, and there is no need to worry about it coming off due to vibration as it is designed to catch on the screw thread in the pulling direction.
After that, the footpeg was finally installed in the same position as the original and this Cap was no longer needed, so I tried to remove it, but this time I had a problem. However, the Slotted screwdriver was not able to be put in at all because of the Smallness of the head diameter and the adhesiveness.
Fortunately, the hole I used is penetrating, so I was able to push it in with a driver and pull it out from the back. If the hole is non-Penetrating, you will need to drill a hole with a drill bit and cut it out with a cutter, etc.
Before you use it, you should really think about whether it's strong enough to cover it up and Large before you use it.
View detail
I wouldn't be surprised if you dropped it at any time.
This is another PetitDress- found at KITACO and ConvenienceParts upItems. upItems. it's totally dress-up, because for practical purposes I don't need this kind of Cap. However, I thought it was well made for that purpose. Anyway, the body is Material:It's aluminum and has been properly treated with anodized aluminum, so the color and The shine is good. Normally, the Bolt cover is made of soft plastic, but it is not made of aluminum. Since it is not deformed, the O-ring is inserted into the hexagonal hole of the Cap bolt with it. This is a good example. The part where the O-ring is properly fixed has a groove digging, and it takes a lot of time and effort to process it. I'm there, so I guess it's no wonder it's so expensive.
However, this O-ring is a tricky one. The one for the smallest M6 Screw has a very small O-ring. So it was Large strange for me to fit it in with my old eyes. And it's probably because of the airtightness of the O-ring. Sometimes it would fall off on its own after a few seconds of fitting. No matter how many times I pushed it in, it would fall in such a way that it would come off of itself. As I observed, it seems that the air between this Cover and the Bolt's hexagon hole is compressed and the force The O-ring seems to be pushed back in. That's how airtight the O-ring is. As I was TRYING, there was apparently a point where the air inside was released and the push back phenomenon was The Large threshold type makes it difficult to push in. I hit it with a plastic hammer and pushed it in (I may not be able to get it off later).
However, I felt that the risk of falling due to vibration while driving was Large. It is not at present, but I must be prepared to lose it. At that time, I have no choice but to buy the replacement parts and deal with it.
I used 4 bags this time, and the cost was about 3,500 yen. Well, it's a good cost-benefit ratio for a dress-up, isn't it, using Pinpoint I think you can be satisfied with it even if you don't have a lot of them. However, because I think that it is not strange when it disappears, I think that other custom parts purchase You might want to buy a spare while you're at it.
View detail
It's not the way it's supposed to be used, but …
When I recently replaced it with an Accossat Wire Clutch Holder
The wire and lever attachment point is a Pierced-type pivot pin
Wire's ThailandCo will be in full view
I was looking for something to block up
I think you could use Cap bolt's Cover and the Pin hole diameter
When I measured it, it was 8mm, so I bought a cover for 10mm
I put it on as soon as I saw it and it was Exactly
I bought the Silver, but there are many color variations
You may purchase one to match the color of the Lever
After that, it might come off due to vibrations, so I'll use a Rubber-type adhesive
I'm thinking of fixing it
View detail
Perfect for blacking out
It is ideal for blacking out the car body
You can easily blind and blacken the Bolt
It is also heat resistant and safe
The price is a bit high
View detail
It could be a little cheaper
I've bought them many times to cover the head of One Point and Bolt
It would be great if you could make it a little easier or increase the number for the same price
It's a tighter fit than you might think, and it won't be gone before you know it
I sometimes buy them because of price adjustments
View detail