Reviews
The quality is not so good for the price
There are gaps and rattles
There's also BALI, which has to be sanded down
I bought Silver, but? It's like
We do not recommend it
View detail
It guarded well
Installed on the rear axle (M's Slider is also installed on the body) Corner exit at about 90km speed, SlipDown due to too much Axel dawn, and I skied for about 20 meters, but the Cowl was only a Small scratch and the Swing Arm was intact It's done
I'm still going to use it for my next fall without replacing it
However, it took about two weeks from the time I ordered it to arrive to see if it was shipped from overseas
View detail
Fits: YAMAHA XSR 700, YAMAHA MT-07, YAMAHA XSR 700
Accuracy X
Right does not fit at all:I hung up a little 2pcBolt and forced it on with the force of the screw
I don't know if it's gonna bite off the Bolt
It's XSR700 compatible, but I don't think it's something you can call compliant
It's cheap and good looking, but..
View detail
Fits: YAMAHA MT-09 TRACER
I bought it for the cheapest price and it's good!
I installed it on my Racer 900
I wasn't sure if I could install it on MT09to Racer, but I was able to install it with no problem I could
It only takes about 10 minutes to install, and the design is simple and I like it so much that I ordered the Front as well It's a good idea
Protection has not been taken care of (and I don't want to be), so I gave it 3 stars
View detail
not fit 2019 sv 650
The rod that came with is too long...i have to cut it short myself to fit...a lot of work and waste of time...not recommended unless they fix this. View detail
I'm satisfied.
Purchased for the XSR700
I hesitated between the Rhizoma product and this one, but the Rhizoma one is more expensive, so I bought this one
Installation is easy, of course, but don't tighten it up by hand, use Hexagonal Wrenches I closed it
The texture and color are good, but it's not a special product, so after the installation, as shown in the photo, it's not It's a little disappointing that the EngineBody and about 1-2mm of space have been created
View detail
I don't know how they work
I've fallen down so many times in the past that I have to put Slider on it! I bought it because I thought it was a good idea
When I received it, I found that the Instruction Manual is the English version and the rough image I was worried because it was the only one, but when I settled down to read it, I read it "Take off the Volt that's on your motorcycle and put this on Right It just said something along the lines of (Lol)
I tried to take off the Bolt, but it's really hard It takes a lot of strength And I have to hold the nut at the back when I put the Slider's Bolt on It was very difficult to do But the parts arrived as they arrive, so I did not hesitate
When I installed it somehow...it's very nice Parenthesis Well, it's just a hobby
I'll have to be careful not to run this guy's performance check
View detail
Almost satisfied
Purchased for the XSR700
Delivery date, scheduled for the end of January, was completed about a month after purchase
Installation was easy, but I was worried about the bolt tightening at the time of installation because it was a little hard, but it was installed with no problem available Also, a 10mm Hexagonal Wrench is required for mounting
The protection effect is unknown, but the Slider's overhang is less, and it is not a problem for Compact I think it's a Slider that's a good idea
It's cheaper than other products and comes in several colors, and you can choose the color you want
View detail
Dress-up Purpose
I don't use the Rear stand at the moment, so it's for dress-up purposes, but I'm happy with the I will use it in the future I will use the Lear stand in the future if I have to View detail
We chose it for its cost performance
It is a combination of aluminum and hard plastic It is an insurance policy in case of an emergency, so I hope it doesn't take an active part
The installation itself is very easy, and if you have the tools, you can do it yourself
View detail
Fits: KTM 690SMC R, KTM KTM 690 DUKE, KTM 690DUKE R , KTM 990 SUPERMOTO R
Unable to install
It was a 13 year old registered vehicle, but the shape of the Lever did not match and could not be installed
Mine was matched by a MAGURA 167MASTER Lever
Perhaps I'm wrong, but I'll post it for now
View detail
with a walking stick before you die
I bought it and installed it because it was less than half the price of the Babyface product I had been wearing for some time
I was able to install it with no problems However, the installation is done by hand by inserting it into the groove hole and turning it
View detail
Satisfied with Cospa
I was worried because the AxleBolt hole diameter of the CB650R only allows for M5 to pass through, but I was worried that the hole diameter of the CB650R together Large Bolt is Quantity:Because it was set, it becomes possible to set only by replacing the OEMBolt and the worrying matter is [Color] Clear. however, the BoltScrew thread of the Set is inaccurate, so if you screw it in as it is, it will not be a good fit for the Screw It felt like it was going to cause a bite
So, unless you are able to finish the screw pile with a modified Dice or Precision File, be careful!
View detail
Best Protection Effect!
Collided with a wild boar that jumped out and hit an invisible wall in Inoya, Toyama Prefecture on October 5, 2019 The bike fell over with a blown up and went sliding with sparks flying off the motorcycle I had a feeling that it was going to break Large, but thanks to this Engine Guard, there was almost no damage It wasn't View detail
It's pretty good for a foreign-made product
I was looking for a Slider for the SC77 and finally came across this product Installation was quite easy, but I didn't have a Torque wrench, so I went to my HondaDream of HondaDream and I had them hang up only the Torque View detail
The axis size is not fit for rear wheel
I ordered the protectors for rear wheel, when i want to install, i found that the rear wheel protectors axis is not fit for rear wheel (MT-10), the axis is only fit for front wheel. View detail
I've been looking forward to this?
Sorry
Before I knew it, it was Cancellation
You may have received an email
We'll just have to wait for Cancellation
View detail
Fits: YAMAHA XSR 700, YAMAHA MT-07, YAMAHA XSR 700
Good shape?
I've been looking for different Engine Guards, and I've found one View detail
Incorrect accuracy, very dangerous
Second purchase
Because the Shaft is not long enough, it can be fixed only about half the length of the Nut groove
It is dangerous because the snagging rate is very small
In addition, if you install a Washer to both, you can't install it either
Shaft is 10mm to 12mm long
Without installing the Washer, I forced it in and tightened it so that the Nut was embedded in the resin It is possible to install it with the following conditions It's easy to come off and dangerous, and there's no choice but to use an anti-loosening agent or rebuild the shaft to make it more comfortable
The pitch is 1.25mm because the rotation of the nut is less than 2 turns and the pitch is the same level of M8
Since the thickness of the Nut is 8mm, the quantity:Pair (for Left and Right) Both of them have only about 4mm of Screw caught in just under 2 turns
I judged it to be either a design error or a defective product that only allows for such a shallow screw stop
I can't recommend it to anyone other than those who can make their own Shaft
Damage as a result of a fall in the Circuit
It didn't come off, but the LINK and Shift change on the Shift side were all destroyed It's all right
It doesn't seem to be useful for anything other than standing moss
View detail
visually satisfied with the appearance of
I installed the Front as well as the Rear, but it is not too large, and I think it is just right large It's not bad looking The instruction manual is also available in English It was very easy to understand and install Now I can customize it again in a classy way The.. (*^^*) It was self-satisfying! View detail