Reviews
Installation could not be done
The two front holes were misaligned with the Bolt position on the Body side and could not be installed.
I asked Manufacturer to check and they said there was nothing wrong with the product itself.
I don't know why, but I decided to return it because I can't put it on.
Please be careful if you are buying the same type of car.
It is a shame because I liked both the transparency and the shape.
View detail
Anxious to install Sukima Large
The gap at the front most part of the body is much larger than NORMAL, and I felt uncomfortable when I looked at it from the side. The gap is roughly 3 fingers wide.
Also, the installation itself is still NORMAL and only 4 well nuts are used to support the screen, so there is a concern that the screen may fall off. Even if the gap is removed, I would like to see a product with clip nuts and rubber washers for installation.
View detail
It's not accurate.
I was attracted by the look of the product.
Frankly speaking, I wish I had not bought it.
It is not worth $27,000.
First of all, BALI is amazing.
My bad for being careless, but the Edge part. Hmm?" Is this BALI…?" So I traced it with my finger and it cut my finger.
In the meantime, the entire BALI removal is a must.
Also, it is a combination of Bracket of Gold genus and Spoiler of ABS resin, and it is hand-finished and processed by puig, and it is Quantity.:Pair (for Left and Right) The shape was different in
When I put it on for the time being, the Right Side hits the DummyDuct as hard as it can. When I cut the Handlebar by force, the Right Side was so hard that it was cutting into the Spoiler and made a cracking sound.
I had no choice but to cut off the area hit by the luther as much as I could, referring to the Left Side, which was not hit.
"If you shave off that much, you can't hit a rock…"
But this time, the Bracket itself of the genus Gold was hit.
There is room on the Left Side but not on the Right Side.
Is there something wrong with the way it is attached? I tried to adjust it by loosening the screw, but it only attaches where it should and it only shifts a few millimeters, so I was out of luck…
Could it be that the DummyDuct of the MT09 itself has become dislodged? I thought it might be a problem, but it wasn't. ….
To be honest, is this a defective product? I think, "I'm going to have to give up and be patient and use it," but since I've shaved it off.
View detail
Fits: HONDA CB500X, HONDA CB500F, HONDA CB400X, HONDA CB500R, HONDA CB400R
It was surprisingly thin.
After installing it, I knew exactly what I was getting into, the Pe LePera is way too thin compared to the OEM!
Above the Rear Sprocket, where the logo of Pooch is located, you can pull the chain by just poking it with your finger. In addition, because it is slightly bent toward Tire side, it touched the chain when pushed by finger. I'm worried that it may hit the chain with this softness while running.
This price is too high for this level of quality, I can put up with it at half the price.
I haven't tried it yet, but I'm hopeful that it will prevent the mud from rolling up, which is its original purpose.
I think the design and look is good. I hope it helps you with your purchase.
View detail
Let's inspect it.
This item cannot be assembled as per the Instruction Manual, I have inquired about it, but no response after 20+ days. If you are unable to craft it yourself, please be careful.
A bad point
Screw is missing 1 pc.
Some Screws don't enter the Nut, perhaps because of the thick coathin? Once assembled through Dice.
Screw can't reach it, it needs 20mm, but I assembled it by my own way, 15mm hexagonal Spacer for some reason.
I thought about returning it, but I like the shape, so I assembled it with no response from the dealership.
View detail
I put it on my CB1300! I had to use a router to get it off!
I put it on a 2012 CB1300SB. the position of the notch of Right Side did not fit I scraped it off with a router and added the color [Color] I bought the Clear, but it's more than 10cm higher than the OEM, so it's really hard to see the front Feel That's why on the highway, you can feel the wind on your shoulders and over the Helmet, but you can feel the wind from under your chin to your chest It's gone Probably a lot easier to use on the highway than the OEM, when the OEM's I used to hide underneath the Cowl, but after I put these on, I didn't have to worry about it, even if it was a lordly ride I like the OEM one better for what it looks like I'm using a handle mirror but the interference is not so bad did not View detail
There is a crack between Body and Bracket in 10,000 KM running!
There is a crack between Body and Bracket that can run 10000 KM and it got worse and worse.. Repair with universal adhesive material but running 500 KM, cracking occurred, quality accuracy too bad. View detail
Cospa bad
Now it is possible to purchase almost the same on BMWOEM at about 8000 yen.
We recommend you to purchase after comparing once.
Installation is easy, but making was sloppy.
View detail
Quality is too low
The shape is too different from when new product is announced.
It is also posted on Puig's HP, although it was horny at Sharp
Products that arrived had rounded corners and had a chunky shape.
Perhaps it was difficult to pull out from the Gold type in mass production.
The price is too expensive rather than cheap making just molding poly Material with Vacuum.
View detail
I want to return it if possible
Unfortunately cutting the Handlebar will interfere with the Handlebar Guard. It is a problem before the evaluation. Regrettably I used the same Manufacturer for my previous Motorcycle. View detail
Processing essential
When I came out to a new product because I was concerned that Rear brake's Reserve tank does not match the color of the car body "Oh!" Although I thought that it was, when trying to install the delivered item on the Instruction Manual, Brake hose from the Reserve tank interfere with the Tandem Footpeg on the side and can not be installed. It should be exclusive for Racer ,,,.
I thought if I could stop Screw at Mu Rear, I thought it would be fine but I abandoned Hose because it bent.
I attached the attached Bracket to the original width and processed it into a Large width, but by chance I just had the necessary mechanics prepared immediately because I was a four-wheel mechanic, so the equipment would be insufficient for ordinary households.
If you buy this product you should ask the Motorcycle store for installation.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
14 year model GSX1300R HAYABUSA
Because the body is Blue, I bought this product because I was looking for Blue's Screen.
First of all, it is 09 - 14, but the shape of R does not match. Thanks to that, we had to remove the Panel around Meter and it could not be installed, so it took time to replace it. Also, after installation, there was a gap in the Panel at the top of the Meter due to forcibly, a step of about 2-3 mm was made on the Cowl side.
In Panel itself, the Length is about the same as OEM, but the height is about 3 cm high, the wind hit is reduced more than I thought.
Regarding coloring, it is deep blue, I like it. Moreover, ETC which was uneasy (Standard Equipment) It also worked safely.
It is nice to see it from a distance, but attention is needed if you care about details.
View detail
Attachment is easy. However, it was thought that the accuracy of a product was inferior pure. There is a crevice between it and a position lamp. A high speed will also become easy, if the location where a wind will hit at the time of a run if
Attachment is easy.
However, it was thought that the accuracy of a product was inferior pure.
There is a crevice between it and a position lamp.
A high speed will also become easy, if the location where a wind will hit at the time of a run if accuracy becomes good and the hit becomes beautiful comes above the bosom and lies down just for a moment.
View detail