Reviews
Power Filter
I replaced it, but could not get a sense of the experience. View detail
Cylinder replacement
I took down the head of the MONKEY to replace the valve, and when I removed the head and checked the cylinder, I found it was damaged. It would be very helpful if I could buy the parts I want at Rose, but the quantity is very limited.:It is not cosmetic as it is a Set purchase. I hope it will be improved. Also, it is R-STARGE+D Squat106, so it is quite fast, but the MaintenanceCycle is short! (Maybe it's just mine?) View detail
Fits: HONDA MONKEY, HONDA CT125, HONDA MSX GROM, HONDA DAX125, SUZUKI Gixxer, HONDA GROM, HONDA SUPER CUBC125, HONDA SUPER CUB110ThailandMODEL, HONDA SUPER CUB110, HONDA CROSS CUB50, HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50, HONDA GORILLA, HONDA MONKEY
It is easy to install.・・・
When tightened, I think the Spring washer is adversely affected. In the end, I took out the spring washer, adjusted the spring washer with the adjust nut, and then tightened the bolt additionally. Maybe I am not using it properly. View detail
Nice but catastrophic malfunction
I really enjoyed this swingarm for about 600 miles. Came out one day and there was this visible crack in the swing from a distance because you have to admire a moto with the new parts every time you exit the house and also to check the tire pressure, ect. I believe it was a one off from the MFG and did not dispute a claim based on being in the US and having to pay all the shipping fees back. Takegawa is great quality parts, I have many more of their parts on multiple bikes but I do believe there was a mistake on this production and or specific swingarm. Spacing was near perfect, torque was on point, something just went wrong. View detail
ab27MONKEY
The adhesive strength of the double-sided tape was weak and it came off. View detail
Fits: HONDA ADV150, HONDA CT125, KAWASAKI D-TRACKER125, HONDA GROM, HONDA GROM, HONDA GROM, KAWASAKI KLX125, HONDA MSX125, HONDA MSX125SF, HONDA PCX, HONDA PCX160, KAWASAKI Z125 PRO, HONDA CROSS CUB, HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110PRO, HONDA SUPER CUB 50
Unfortunately, I did not feel any physical change!
We have already installed Takegawa's SCRAMBLER Exhaust System, Power Filter, and Hyper Ignition Coil. After installing the system and running the car for a day, I can honestly say that there was no perceptible change in the vehicle's performance.
I could hardly feel it. As mentioned in the BowerFilter's Impressions, BackFire, which was not present in NORMAL in all other cases but only in Takegawa's SCRAMBLERExhaust System, now sometimes occurs when ThrottleOff!
Since the bower filter and Hyper Ignition Coil were replaced at the same time, the cause is unclear, but I would like to reassemble and verify to see if there are any defects in the assembly.
I will make more impressions when I have more miles on the car.
View detail
Fits: Others , HONDA GROM, HONDA MSX125, HONDA MONKEY125, HONDA SUPER CUB110, HONDA CROSSCUB110
I don't want it in jc92Clutch.
I don't use it to replace the Clutch on my jc92.
Clutch lock nut is 19mm.
View detail
heavy work
The welding distortion of the bracket was so bad that I had to forcefully insert the bolt by pushing and pulling the body and bracket and inserting lubricant. I thought it was the manufacturer, but the welding distortion of the bracket was so bad that I had to push and pull the body and the bracket, and forcefully put in the bolt by inserting lubricant. If you continue like this, there will be returns. I think it will cause trouble for the distributor as well. It's a shame because the paint, overall texture, and quality is good. View detail
Fits: HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA SUPER CUB 50
Easy Custom but not recommended as a product.
Was the one you received as per Image?
To be honest, I'm not sure what part of these plastic parts cost 5,000 yen. (Lol)
There is a great sense that they are only chosen because there are so few options.
Was the installation difficult?
It can be done in less than 15 minutes, changing back and forth.
How was your experience with it?
Anyway, the problem is that the early Orange Lens is lame. So, we have to go to the trouble of replacing them, and the manufacturers are also looking down their noses at us.
If the cost is not that much different, I hope Honda will make Clear Lens LED Blinker from the beginning.
[Was there anything that disappointed you?
First of all, the cosmetics are very bad. It costs 10,000 yen for front and rear replacement.
I replaced it with the Orange bulb that came with the kit and activated the blinker before tightening it, and found that one of the bulbs was cut off.
If this Orange bulb was from FOR JAPAN MODELManufactureretc. it would have been a little sweeter, but I honestly do not recommend it.
Other items that would be helpful
Points to note
The Orange bulb that comes with the product may be out of balls from the start, so you should buy the Orange bulb together with the product. (Lol)
Opinions and requests to Manufacturer
The manufacturer has been very helpful to us with CROSSCUB CUSTOM, so we were quite shocked when the Blinker bulb ran out of balls this time.
I no longer care about the price, just do something about the attached Valve Quality.
View detail
Fits: HONDA GROM, HONDA MSX125, HONDA CT125, HONDA GROM, HONDA SUPER CUBC125, HONDA MSX125SF, HONDA MONKEY125
Takegawa oil pump
Morin Oil cooler could not be installed. Sorry, I can't confirm the effect during removal.
The production is as good as it gets.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB 50
Cancellation
I have not used it yet. I would like to Cancel my order. View detail
I don't know.
The cut edges on both edges of the surface are painful because they bite into the crotch.
I can't sit for long periods of time.
View detail
For the amount of Gold?
I'll be dry.... View detail
The area near the Screw stop Plate at the Center has rusted.
A packing cord is also included for ease of use.
However, it rusted within six months of purchase.
I don't ride in the rain. Protect your car body with Cover when you go out.
Home is kept at Garage and not on the coast.
And once a month. Raspene." I was wiping the CROSS with the CROSS.
I will not purchase any more.
View detail
Fits: HONDA MSX GROM, HONDA GROM, HONDA MONKEY125
Caution, oil lubrication is required for bearing every 500km.
This is the third bearing to prevent shaft shake of the crankshaft.
It is not to be used for crankshafts that are already shaky, but as a preventive measure.
If you follow the instruction manual, you can do the work in two hours.
A Special Tool (PulleyHoldWrench, or RotorHolder as it is called at the site of purchase) is needed to remove the center nut of the crank pulley.
On the crankshaft side, note the mounting orientation of the spring washer.
The BearingHoldPlate looks as if it is installed on the opposite side from the picture in the instruction manual, but it can only be installed as shown in the attached picture.
The Purchase Site states that it is a 3-point support, but I think this is a lie.
I bought it with Image which supports Shaft like Wheel bearing, but when I installed it, there is a little gap between special Lock nut which extends the shaft and Bearing.
In other words, the Bearing side (Generator Cover side) is not firmly supported as a third bearing. ＞See photo.
Perhaps it is an insurance mechanism that acts in the event of large-grain axial shake (deflection motion).
So, it may be necessary for people like me who run the car at high RPM spec, but it may not be necessary for those who run a full two wheeler.
The last part of the instruction manual contains an outrageous note. ＞See photo.
”Bearing is to be lubricated every 500 km”.
This would be redon't you think, because if the lubricant runs out, it will cause resistance to rotation of the Shaft.
It is not a Race vehicle and this MaintenanceCycle is not practical.
This is the kind of information I want to know before I buy, but PurchaseSite doesn't list this kind of warning. This is also redundant.
False 3-point support, impractical MaintenanceCycle, it might be better not to introduce this Parts. I have trusted SP Mukawa's functional Parts until now, but as expected, I'm going to say no to this one.
The quality and texture is not as expected for a functional component, so it is 1 star.
I don't know about durability, as I have not tested it, but since it is not supported at exactly three points, I will leave it out of the discussion.
However, the overall rating is 2 Stars with high hopes that it will be an insurance policy for people like me who DRIVE at high RPMs.
View detail
Hmmm…
I replaced it while I had it in stock for the oil cooler installation.
First of all, the included PrimaryGEAR is useless!
Torque will be extremely low ←You can cover some of it by diverting to other cars.
Furthermore, it is possible to replace it with a hydraulic kit, but it is already discontinued, so you need to look up the number from Repair Parts and buy it.
Other than that, I have no complaints, but I think it's a surprisingly painful area, … what do you think? Mr. Mukawa.
View detail
Fits: HONDA GROM, HONDA GROM, HONDA GROM, HONDA MSX125, HONDA MSX125SF, HONDA CT125
92 groms were not combinable.
First, I tightened it with the specified Torque8N/m and it broke.
The anodized part of the screw was uneven and I am not sure if this was the cause of the breakage or not. I am not sure if this was the cause of the breakage, since all the screws were similar.
Quantity:2pcs broken and only 4 replaced 7~7.5N/m Bolt length 20mm is quantity:There are 2pcs left over.
For Mr. Mukawa, it was a rare dud.
I had a Engine slider, so I thought I could use 6 screws, but I broke them, so I had no choice.
Incidentally, the Right Side is not usable because it is 40mm compared to the NORMAL 35mm. So, I purchased an additional LeftBolt, but the same thing happened here. It is a pity.
Quantity:Pair (for Left and Right) We use four of each only where we can see them.
I would not recommend a 92 Grom, but a type 2 Grom might be a good choice.
It is made of aluminum, so it is very light.
View detail
Fits: HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125
I have never Larged.
Torque up dramatically since I changed this!
There is no way that this will be the case.
It increases the crispness of the sound, the reduction of After Fire, and the feeling of acceleration just a little bit.
A slight difference of about 5-10% will be made.
View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA CHALY 50, HONDA CHALY 70
It worked too well for me and didn't suit me.
I wanted to improve the ride quality of NORMAL and bought this product thinking that adding Damper would improve it.
I could see the effect of Damper as soon as I rode on it after installation.
The most effective is when there is a Large input, and Damper absorbs the bumps that would otherwise cause the Normal to wobble, making the ride much more stable.
However, it didn't work out as I had originally intended. I have a weak stomach, but after riding long distances, I started to get a stomach ache.
After removing it again, I found that it can be driven normally up to 70 km/h with a good feeling of control even in NORMAL. And the ride is comfortable.
Beyond that, it is more stable to run with Damper. This was the reason.
At low speeds, there is a lot of Damper Friction and a feeling of suddenly collapsing.
I have found that my riding style is better without Damper.
I may be able to make use of this Damper by increasing the load on the Front when the Front is fully loaded or by extending the Rear Swing Arm, so I will give it a try.
Our Vehicle Specifications
88ccBore up
Maximum speed 90 km/h or higher
Swing Arm is NORMAL
Only the rear suspension was changed to a Gas shock with a Takekawa adjustment mechanism.
View detail
Fits: HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50PRO, HONDA SUPER CUB 50PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA SUPER CUB110PRO, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA CROSSCUB110
How does it work better than it looks?
Installed on JA45 CROSS CUB.
When I put it on my other JA07 SUPER CUB, the touch became much better and I immediately put it on my CROSS CUB.
It did not improve Touch as much as we expected.
Compared to NORMAL, which is made of steel plate PRESS, Aluminum Casting has a higher quality look and feel.
You've been told well Brake Performance Improvements." does not exist because BrakeSize does not change.
If you want to improve the effectiveness, you should replace the Shoe.
View detail