Reviews
Caps are consumable.
I decided it was time to replace the Radiator cap on my CB400SB. I like it because it is Reasonable and cooler than OEM. View detail
It's nice
I bought a used TRX850 that was a Fender Eliminator with a Silver T-Bracket and a square Reflector.
The bracket is black and I like the shape of the Hexagonal, so I bought it.
It's better now. If I could do a little more reduction in cost, it would be great.
View detail
The REBEL250 SEdition came with a Large
I bought this for my REBEL 250 SEdition to attach the FrontCamera drrorecorder to it.
of the same product before purchasing this one. "Φ40-Φ45" I bought the Size, but the Size was just a little short, so I bought this additional one.
As a result, this one was too large.
This is "Φ49-Φ54" So I thought I could make it work, but it seems that the middle Φ47 or so is Just fit.
If you are concerned about installation, etc. "Φ40-Φ45" I've also reviewed the Size, so please check it out.
The Bolt could not be installed there, so I used the Tie Band.
This one is too loose, so I put Seat in between.
I can't decide which is better yet, but I don't think there will be a large change if I buy either size, since it doesn't shake that much.
View detail
I expect it to be durable.
I've been looking for a large stone to put under the side stand when I park on uneven terrain when I'm touring.
It became a hassle and I bought this one.
I used to use an unnamed manufacturer's product for the Garage, but the reverse side was cracked in small pieces and I rejected it.
I'm going to use the large STANDPad I bought the other day for Garage and this one for touring.
Now I expect it to be durable enough not to crack.
View detail
It was a little short for the REBEL 250 SEdition.
I bought this product because it is compatible with the REBEL 250, but it was not long enough for the SEdition with Fork Boots.
I thought it might be a little loose, but it feels fine for use on regular roads.
Since the Dr-Recorder is made in China, I can't use Bolt, so I use Double-sided Tape to attach it to Bracket.
View detail
For RearCamera!
I've installed it to fix the RearCamera on my Mistuba Sankova front/rear drrorecorder!
I can install it without any problems, so I recommend it to anyone who's going to install a Dramalec!
View detail
Less Chemical waste.
It helps with Throttle and Clutch Wire lubrication.
If you don't have one, you can just lubricate it steadily, but if you have to do several, it will take an endless amount of time.
If you have one of these, it's worth buying because it's a big efficiency boost!
View detail
After all, cbr1000rr-rSP is now a Recall
I've been thinking that the RadiatorCap on the CBR1000RR-R is fishy.
I was thinking and bought this product. I was waiting for the Recall to be delivered because I didn't want the Engine to burn up on the ride.
It is now a Recall and will be replaced next time.
I bought this product to try because the Engine has a very high heat level. The opening valve pressure is 1, 3 but there is no problem, in my opinion.
View detail
Note the length of Drill.
If the Drill length is too short, the hole cannot be drilled. View detail
Ninja 250 Front fork oil change
Ninja 250 Used on a 2014 Front fork oil change. Easy to use and works well. I recommend it. View detail
Fits: YAMAHA RZ350, YAMAHA XJ400ZS, YAMAHA XJ400ZE, YAMAHA XJ400Z, YAMAHA XJ400, YAMAHA XJ400D
Relief
I bought this because I went with brembo.
Of course, Exactly is attached, but you need to adjust the Shim to get Center.
View detail
RearCamera will fit Refreshing!
I use it for my Mistuba Sankova drrorecorder.
At first I thought that RearCamera is better from the side of License Plate, and I installed OEM Camera Bracket (NanBar mount) of Mistuba Sankowa, but I chose this one because it covers Blinker.
To tell the truth, this had been put in the choice from the beginning, but from the fact that I have made Fender Eliminator, thinking that the space of installation cannot be taken, I selected the one of putting out horizontally, but with Compact more than I thought Camera of Mistuba Sankoowa, it turns out that there is enough space It turns out that there is space, because the one which puts out from the top does Refreshing, it became the purchase again.
Because the Number angle of Fender Eliminator is sleeping considerably, I thought that it was severe in terms of the angle of Camera, but because the installation angle of Camera was also relatively free, it was possible to install Limit without bending.
I hope it's black. It would be nice if they were black. I painted them black after I installed them.
Refreshing around the License Plate, too, and it is highly satisfactory.
View detail
EDR-21G RearCamera
I used it to mount the RearCamera on my EDR-21G.
This in itself is easy to install.
The hole didn't fit, so I bent the Bracket's Camera mounting part and installed it.
View detail
For weak legs and feet (laughs) a twist
I used Magic tape to attach it to the Tank end for Breaking and Machine Hold in Circuit driving.
You can add a piece or two to the Position of your choice.
I did not hesitate to fail because of the low cost.
It's very good.
View detail
You can use it.
It is used with Ninja 250 Front forkOH, and it is easy to use, and I am glad that I bought it. View detail
It's a bit forced. Crying 。
This is a must have part for brembo installation.
I was not sure if it was Radial Mount or Axial Mount, but Axial is enough because it is OverQuality.
To install, just mount it on the Front fork and assemble the Caliper.
However, Aluminum Cut-out is not the same as "It's just the way it is. The feeling is ……
I think GCraft's Black Anodized Aluminum was more natural. (Sweat) 。
View detail
For EDR-21's RearCamera
I tried to make my own with EmonBracket, but if you have such a good bracket, there's no reason not to use it. I was able to mount the RearCamera on it. It was easy to adjust the angle of view. View detail
You don't have to worry about where to fix it.
[How is it used?
I used this product to fix the RearCamera in order to attach the DriveRecorder to the Motorcycle.
Installed model is YZF-R15 (MODEL in 2012) This is a MinorMotorcycle, but the license plate is the same as other motorcycles.
How was your experience with it?
I used it to fix the Dr-Recorder of the unidentifiable Manufacturer of China sold in a certain ShoppingSite.
This was a happy miscalculation, but the position of the holes in the bracket and this product are Exactly the same. (Although it's made with long holes for easy installation.) It was
I was able to attach it perfectly using the included fixing Bolt and Nut, so I'm happy.
After checking out the video, I thought I had made a good purchase with the smallest amount of shake necessary.
How did it compare to other products?
I compared it with KITACO and Posh face's Drraco Bracket.
I chose this product because it had a good rating and the installation image was easy to understand.
【Review】
Bolt nut for mounting was also included and the angle and accuracy was perfect.
At any rate, if you buy DriveRecorder, I think that Rear stay is indispensable though it doesn't matter what kind of thing.
I have several motorcycles, so I also bought a DAYTONA drum recorder as a comparison, but its shape is a little different from the Bracket. I thought it was the same thing, but it's not. Sweat
View detail
It is recommended to mount the Camera on the License Plate Bolt after mounting the Camera.
I bought this for the installation of the RearCamera of Mistuba Sankova EDR-21Gα.
I think it's better to install the camera after you install the camera.
The Nut that comes with the installation is M3 and small, so I didn't have the right tool on hand and lost the Nut and went to the home center to buy one.
Be careful
I bought the one for the upper Left, but I think the one for the upper Right might have been better for the angle of view.
View detail
Maybe not for upright Fork.
I bought this product to install the FrontCamera of Mistuba Sankowa EDR-21Gα, but I tried to install it to the non-moving part of the upright Fork of our vehicle, but I could not find a good position and gave up using this product.
It might be good for Inverted Front Fork.
View detail