Reviews
Fits: YAMAHA MAJESTY125, YAMAHA CYGNUSZ, YAMAHA BW'S R, YAMAHA BW'S125, YAMAHA BW'S X, YAMAHA BW'S125, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
I'll wait for someone to post the results to see if there are any bad effects.
I'm holding off on replacing it because I think it might have the same effect as lengthening the belt because the OD is smaller and reaches deeper into the Torque Camshaft groove, but it would increase the rattling in the groove, so I thought I could wait until I see what someone else has done before replacing it. View detail
It's a Repeat session.
The outer diameter for CHAMP is 1mm too large to fit, so this can be installed on Smooth. View detail
Fits: HONDA TODAY, HONDA TODAY, HONDA DIO 4 Str., HONDA DIO4st CESTA
6 months of use
Self-replacement, riding for 6 months, there was a speed increase of about 10km, but at some point, the initial torque did not rise and the vehicle did not move. I do not know, but I returned the parts to the original condition --------------------------------------- ------------------- Self -replacement, riding for six months, and a 10km speed up, but from one point, the early torque did not rise and the vehicle did not go. The vehicle was checked. I'm not sure, but I put it back with a pure part. Powered by Google Translator View detail
Fits: YAMAHA Jog (2 cycle), YAMAHA Vino (2-stroke), YAMAHA Jog Aprio Type 2, YAMAHA Apprio, YAMAHA Super Jog ZR, YAMAHA JOG50 Only for vehicles before exhaust gas regulation, YAMAHA Super Jog ZR, YAMAHA JOG50 Only for vehicles before exhaust gas regulation
Purchase Repeat
Another Review The Unexpected Cooling Effect." The overall thickness of the fan is noticeably thinner than the 3WF OEM fan. (However, since the feathers are offset to be Large on the generator side, the Large size of the feathers themselves does not make much difference.)
Again, I will try to quantitatively examine the difference in Head temperature with ThermistorSensor, but I feel that 3WFOEM without Offset is more advantageous since it is a fluid structure that inhales from the inside of the fan and exhales to the outside.
Incidentally, since the wings interfere with the PALSA Coil due to the offset, a small modification is required to slightly tame the PALSA corner with a file.
View detail
Fits: YAMAHA JOG90, YAMAHA Axis 90, YAMAHA JOG80, YAMAHA JOG-Sports, YAMAHA CHAMP80, YAMAHA Target RS90, YAMAHA Excel, YAMAHA Active, YAMAHA BOXN, YAMAHA JOG, YAMAHA CHAMP, YAMAHA CHAMP RS, YAMAHA SUPER JOG ZR, YAMAHA JOG, YAMAHA APRIO, YAMAHA APRIO type2, YAMAHA APRIOEX, YAMAHA JOG, YAMAHA JOG-Sports, YAMAHA VINO
High turnover type, my favorite.
Even with the additional weight, the gearshift is still very high rpm. I like it because it is Exactly for my current engine characteristics. View detail
![[Repair / Optional Parts]Clutch Outer](https://img.webike-cdn.net/catalogue/images/60539/04152338_5cb4974d6a9ce_TS.jpg)
Fits: YAMAHA FORCE 155, YAMAHA SMAX, YAMAHA Majesty S
OEM Product and the same etc.?
I bought a product that I thought was the same as the OEM product because I didn't want the RPMs of the clutch meat to go up. The Judder was resolved and I am satisfied. View detail
Fits: SUZUKI sepia, SUZUKI sepia, SUZUKI sepia, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI sepia, SUZUKI hike, SUZUKI hike, SUZUKI Address V(90-95), SUZUKI Address V(90-95)
Although it was cheap, it was thought that it was durable. (There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used. I t
Although it was cheap, it was thought that it was durable.
(There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used.
I think that 16 mm of WR(s) are the strongest to address v100 processing pulley.
View detail
Fits: SUZUKI sepia, SUZUKI sepia, SUZUKI sepia, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI sepia, SUZUKI hike, SUZUKI hike, SUZUKI Address V(90-95), SUZUKI Address V(90-95)
Although it was cheap, it was thought that it was durable. (There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used. I t
Although it was cheap, it was thought that it was durable.
(There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used.
I think that 16 mm of WR(s) are the strongest to address v100 processing pulley.
View detail
Fits: SUZUKI sepia, SUZUKI sepia, SUZUKI sepia, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI Address 50, SUZUKI sepia, SUZUKI hike, SUZUKI hike, SUZUKI Address V(90-95), SUZUKI Address V(90-95)
Although it was cheap, it was thought that it was durable. (There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used. I t
Although it was cheap, it was thought that it was durable.
(There is also a cause which is carrying out grease up frequently ?) WR of this size -- the other company -- a weight -- up to 8g -- about -- since it does not spread, Kn plan is used.
I think that 16 mm of WR(s) are the strongest to address v100 processing pulley.
View detail
Fits: HONDA Giorno2, HONDA Byte, HONDA CREA SCOOPY, HONDA GIORNO CREA, HONDA SMART DIO-DX, HONDA SMART DIO
It didn't sacrifice low speeds as much as I thought it would.
GIORNO CREA has a weak center spring, and shifting starts almost as soon as the car starts, so the weight roller was set 1g lighter than the attached one, and the 0.3mm boss shim was used to make the Belt drop deeper to slightly raise the Engine RPM at low speeds. The weight roller is 1g lighter than the supplied weight roller, and a 0.3mm boss shim is used to increase the engine rpm at low speeds. By doing this, I think I can solve the problem of low speed leaning that is often seen with high speed pulleys. I think that the best setting is to set the center spring a little harder and make the weight heavier, while slightly licking the weight roller surface of the pulley and shifting it a little to the high rpm side within the range not exceeding 8000 rpm. View detail
Fits: YAMAHA JOG, YAMAHA VINO, YAMAHA AXIS 90, YAMAHA GRAND AXIS, YAMAHA SUPER JOG ZR, YAMAHA BJ, YAMAHA BWS100(BWS), YAMAHA BWS50, YAMAHA APRIO, YAMAHA JOG, YAMAHA JOG, YAMAHA JOG90, YAMAHA JOGC, YAMAHA YV50 Z II, YAMAHA JOG Zr, YAMAHA SUPER JOGZ, YAMAHA VINO(2Cycle), YAMAHA Remote controller jogZr
Not very effective in Normal spring.
Used in 4jp5APRIO
I was considering whether to use a stiffer center spring when I remembered this product, so I purchased it.
I thought that if I put the BearingSlider in before stiffening the Sensep, I would be able to apply a little more load to the Spring than in the OEM condition.
I'm not sure how effective it is, but I think it will be useful when I replace the Sensep and make it harder, because I think it will absorb the twisting.
As for the quality and texture, well, there is a slight BALI on the processed finish, so I lightly removed the BALI with sandpaper before injuring my hand.
The precision of the ball in the Slide section was also gurgling when turned by hand with load, so I put a few drops of Bell Hammer Gold on it and turned it by hand until it became accustomed to it.
The gurgling feeling is almost gone, but I think it is better to degrease the oil thoroughly before assembling because it may fly out.
I don't think it is necessary to add oil to the parts since they are not usually high-revving parts.
View detail
Fits: YAMAHA BWS (Bewith), YAMAHA BWS (Bewith), YAMAHA Apprio, YAMAHA Apprio, YAMAHA Apprio, YAMAHA gear, YAMAHA jog, YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog ZII, YAMAHA Jog ZII, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA jogpochet, YAMAHA Super Jog ZR, YAMAHA vino
0.It's a product for determining RollerSetting in 25g increments.
I was looking for a roller with 0.25g increments to fill a Weight RollerSetting and found this product.
5.0g×3 pieces 4.5g×I was running with 3 Settings, but I wanted to go a little heavier, so I changed 4.5g to 4.75g.
Scooter is fun to use, even with a total 0.75g increase, it changes the way it runs!
Durability has not been tested yet, but it would be great if it doesn't wear out as much as OEM.
View detail
Fits: HONDA clair-scoopy, HONDA Gyro UP, HONDA Gyro UP, HONDA gyro X, HONDA gyro canopy, HONDA Johno., HONDA Journo Clare, HONDA SmartDio, HONDA Dio (4-stroke), HONDA Dio (4-stroke), HONDA TODAY., HONDA Livdio ZX, HONDA Gyro UP, HONDA gyro canopy, HONDA SmartDio, HONDA SmartDio, HONDA byte
Unsure how long it will last as I don't trust the quality.
I decided to replace the Belt, Pulley, and Clutch because I have no idea how the drivetrain has been taken care of on a used car with unknown mileage.
The arrows are marked, so be careful of the direction when replacing.
When the belt cannot be attached, the clutch can be widened to allow the belt to drop down and rest on the shaft on the pulley side.
Even with a reasonable one, the speed is normal because it is new.
I don't trust this Manufacturer's products now, so I will use something else the next time I replace it.
View detail
Fits: YAMAHA VINO, YAMAHA VINO, YAMAHA VINO, YAMAHA JOG, YAMAHA JOG, YAMAHA JOG
sure
It makes city driving super comfortable. And the price is reasonable, thank you! View detail
Fits: YAMAHA Tricity155, YAMAHA tricity, YAMAHA Tricity155, YAMAHA tricity
It was cheaper than OEM Product.
I purchased this product as a Belt replacement for my Initial ModelBirdCity125.
The reason for our decision was that it was cheaper than OEM Product and we had used the same Manufacturer's product to replace the belt on a 50cc Scooter we had previously ridden.
The vehicle was bought used, so the BeltTrip was the same as the Odo, but the OEMBelt that came with it was not particularly thin or cracked…….
I hope this Belt will last as long.
The Roller was also replaced at the same time, and after the replacement, the start was smoother.
View detail
Fits: SUZUKI LETS4Palette, SUZUKI LETS5, SUZUKI LETS4Basket, SUZUKI LETS4, SUZUKI LETS4Palette, SUZUKI LETS4Palette
Good quality
A reasonable price. a performance similar to that of a genuine product. I think the durability is okay, too. I am satisfied enough. View detail
Fits: SUZUKI Address V100, SUZUKI Address V100
For periodic replacement of the drive train
Since the mileage is now over 35,000 km, I thought that both Belt and Pulley were probably deteriorated and worn out, so I bought them.
I replaced it myself.
The Nut (24mm) that holds the Pulley in place is tough without an Impact wrench. By the way, it is an Opposite Thread Screw.
I think both Belt and Pulley are OEM Product quality.
I went with DAYTONA 12.5Gram because the weight roller that came with it was too light.
They run well.
View detail
Fits: HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Livudio SR, HONDA Livdio ZX, HONDA livudio
Not recommended for AF27SUPER DIO
Ramp Plate of AF27SUPER DIO Late Thick Shaft Type was broken, so OEM Parts (
(22131-GAH-720), but had no choice but to order this as it was discontinued.
However, when comparing this product to the AF27 OEM Product, the thickness is 3mm thinner and the amount of the pulley boss protrusion is reduced, which causes the drive belt to not drop inward, resulting in a condition like 2nd gear starting.
As a first aid measure, AF27 can run for a while, but I think this is almost the same Size as AF28's 22131-GAH-780.
Although the product is compatible with the AF27SUPER DIO, it is not recommended for use with the AF27 SUPER DIO.
View detail
Fits: YAMAHA Jog (2 cycle), YAMAHA Vino (2-stroke), YAMAHA Jog Aprio Type 2, YAMAHA Apprio, YAMAHA Super Jog ZR, YAMAHA JOG50 Only for vehicles before exhaust gas regulation, YAMAHA Super Jog ZR, YAMAHA JOG50 Only for vehicles before exhaust gas regulation
Unexpected cooling effect
I was skeptical, but I am quite satisfied with the cooling effect. The temperature dropped by about 20℃ from 135℃ with the normal fan to 115℃ with the reinforced fan. I like the sound of the Normal fan because it has a nice humming sound. View detail
Fits: YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA jog sports, YAMAHA Apprio
I do not recommend it.
The inner diameter of the pulley boss seems to be slightly smaller than the OEM product, so it could not fit in the shaft and could not be installed. View detail