Reviews
emergency measure
Finally, the end-Quantity:The Thailand coil of GB250 CLUBMAN's clutch wire broke and I used it as a first aid kit. The wire was out of order at the point where it was cut, so I used an on-board tool to adjust the tip and cut the end-quantity.:I inserted it into the set and fastened it with the included Hexagonal Wrench. I was surprised that it worked better than I expected, and it is a good thing to have one with you when touring. I learned a lot this time because I can work faster if I have a nipper to adjust the wire. I will add a Nipper to my on-board tools. View detail
Cheaper than OEM
We purchased more because they are cheaper than OEM!
When they are old, they are hardened and I replace them when they are Rose.
This is a necessary component to prevent Cowl from cracking or over-tightening!
View detail
Recommended
Used when Oil cooler is installed!
I hate colored stuff and there is Black and I bought it!
Simple and Parenthesis good!
View detail
I use it to organize Wiring
Battery charging terminal for external charging and USB navigationetc.… Used to organize all kinds of wiring.
Unlike cheap vinyls, it is stress-free because it is not sticky!
This is Stress-free! I will definitely recommend this one!!!!
View detail
Used for 250SL (Repair)
I bought a new Ninja 250SL… because I lost my push rivet at some point.
I purchased and used it. The quality is high and I can use it without any problem, but I still feel that it is rather expensive…
View detail
Shiningly glowing and looking great!
Gold color is beautiful!" and my neighbor's beautiful girl gal JK is very receptive lol!
Gold color seems to be accepted by gals… Riders who want to be accepted by gals, let's install it!
Recommendation！
View detail
Spring resonance subsides.
I was concerned about the sound of the Spring installed at the connection points of each part of the Exhaust System resonating while driving. My car's spring was not equipped with an anti-vibration rubber tube, so I purchased this spring. After checking the length and thickness of your car's Spring, you will be able to choose the one that fits it.
Since the Tube and Spring are Exactly and Fit, it is better to apply a small amount of lubricant when installing the Tube and Spring for better workability.
After installation, I am satisfied with the effect and Large change.
View detail
It's cheap and can do dress-up, but …
Easily dress-up with no tools required! … but it fades quickly lol
I've had it for a few years… but it's cheap, so why not! LOL!
View detail
It's a thin rubber board." It's easy to cut with Cutter or Scissors.
As per the Title, it can be easily processed with Scissors or Cutter.
It has many uses, such as anti-vibration measures for Motorcycle or under a tool box.
It's reasonably priced and it's a RECOMMENDATION!!!
View detail
For emergency spare parts and maintenance of old cars
[How is it used?
TZr250R (3XV) I purchased this as a spare/for replacement for the Throttle Wire of
We chose this product because it was inexpensive and the Size feel seemed fine.
Was the one you received as per Image?
L-Type Wrench is included as shown in the photo.
Since it takes up very little bulk, it is convenient to carry as a spare.
How was your experience with it?
It is stored in the storage space under the Tandem seat for emergency use when touring.
Fortunately, we have not yet encountered a SCENE to use.
TZr250R (3XV) In the case of the "Oil Pump", the OEM Product is discontinued and there is no Replacement Product due to the complexity of splitting the 1 pc Wire into a carburetor, YPVS, and Oil pump.
Many used ones are also in poor condition, and since they are consumable parts that will have to be replaced at some point, they will not be wasted as long as you continue to ride because you will eventually use them when that time comes.
[Points to note]
It would be nice to have a Wire cutter to adjust the length.
How did it compare to other products?
The delivery time was so long that I also bought a No Brand product sold at a certain Large Hand NetShop just in time.
Fortunately, I have not used either of them, but the No Brand product did not come with tools, so I think this product is better for emergency use. I think this one is better for emergency use.
【Review】
Although it is best not to use it, it is a product that can be soldered for emergency use or for long-term use, so it will not go to waste.
I have had to push Motorcycle for an hour in the past because the Wire ran out, so it is a good idea to have it with you to avoid that kind of feeling.
View detail
Less expensive than OEM Parts
[How is it used?
I used it to fix my newly purchased Chinese Cowl.
I bought this product because it was inexpensive and had good reviews.
Was the one you received as per Image?
I purchased For M6, but it is surprisingly Large, so it is somewhat troublesome to extend the lower hole.
Was the installation difficult?
The Chinese Cowl originally has an appropriate hole Size, so the hole needs to be expanded.
The work must be done carefully because it has to be made rather Exactly.
It is recommended because it is easy to use once it is fixed.
How was your experience with it?
It is strong enough to fix Cowl.
As mentioned above, Chinese Cowl would be useful as long as the pre-drilling is done properly. (Actually, I prefer Quick fastener, but...)
Note that the price is surprisingly high when used in large quantities. Still, it is much cheaper than OEM parts.
[Was there anything that disappointed you?
Although the product itself is not so great, the size is indicated as large, but I thought it was difficult to image the size.
I felt it would be easier to buy if compatible OEM Parts numbers were listed.
【Review】
It is useful for fixing exterior parts such as Cowl and Screen.
OEM Parts are expensive, so if you want to keep the price as low as possible, this is a good option.
View detail
diversion
I bought it for my SCUB, so this time it is a push rivet, but I used it for my PCX because the push rivet was damaged when I changed the battery of my PCX. I wish it was a little more cost-effective. View detail
On Axle Shaft
Purchased because it is easier to replace the pin every time when loosening the Axle Shaft for Chain Maintenance etc.
I think it looks good because it is Stainless Steel and there is no Rust.
View detail
Material:Stainless SteelSplit Pin
I needed a Split Pin for cleaning a Caliper on a CB1300.
This Split Pin is Stainless Steel, so I think it is rust resistant. It is not reusable, but Material:I think Stainless Steel is good. Also, if you don't know the Size, it is helpful because it contains several different Sizes.
View detail
Good to know! I use it for Reserver for Rear brake master.
I am using it as a reserver for the rear brake master of a custom vehicle with a disc brake.
When I lost my rear brake due to a crash during a course run, I had a fierce guy who melted and glued it back together as a first aid measure, but the reinforcing pate also peeled off and I was still worried, so I replaced it.
The *Repair person told me to change it immediately after the run.
It's a good thing we have these parts! I think the original parts on my car were probably OEM parts, but I think I understand why Tank Guard and other parts are sold nowadays....
No problems with quality, etc. I bought another one as a spare just in case.
Not everyone may use it in the same way, but it may be helpful to you.
View detail
The peace of mind of being able to see directly with your own eyes
As others have said, you can write your maintenance history in your phone or Memo book.
This product is not necessary, but it is something that can be directly attached to the car body for confirmation.
For some reason, there's quite a sense of security in knowing that you can do it, lol.
The durability of Sticker is also high because it sticks to the car without peeling off in the rain or car wash.
It's expensive, so it's RECOMMENDATION!
Multiple piecesQuantity:I'd be even happier if you sold the Set at a discount!
View detail
K-CON Connector Set
About quality and texture The product is of good quality About the feeling of use I couldn't install it because of the wrong purchase Products to buy together Connector shape female, male. This is the set that you have to buy Difficulty of installation Installation where necessary Cost performance and comparison with other products The price is better than other companies' products and the quality is better About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing When I received the package and looked at the connector, I bought it because it was 3p in the picture on the product page, but it says 2p in the product description I'm afraid I have to use it well View detail
for the occasion
[How is it used?
I bought this when I was organizing my commuter CUB Wiring, which has been a mess since I bought it, for Earth.
Was the one you received as per Image?
As per Image, AutoBacks and Color:I could have gone to YellowHat to buy them, but it was a hassle, so I bought them at Webig while buying other parts. It is very helpful to be able to buy something on the side.
Was the installation difficult?
Crimping with Electric Works Pliers is OK. As a side note, Electric Works Pliers are KNIPEX's recommendation for extra-thick pliers. Cheaper types have a thinner body and cannot be crimped properly.
Wiring relationships work best if you buy Electric Works Pliers that are as tough and thick as possible.
Rob Star (Shrimp) I remember that the good ones of the "Mere Old Man" were also so-so and thick.
How was your experience with it?
Neither good nor bad
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Electric Works Pliers can last a lifetime if you buy the right ones, so go ahead and splurge!
View detail
The price is more than twice that of OEMBolt, but w
[How is it used?
When replacing the Rear Disc Rotor with a new one, I also decided to buy a new bolt, since it is prohibited in principle to reuse a rotor bolt. The price of OEMB bolts is 110 yen per bolt, and this Stainless bolt is 253 yen per bolt, which is more than twice as expensive, but the total price of 6 bolts for one Rotor is 1518 yen (including tax), so I decided to go ahead and buy them. I thought, "Oh well, there is no point in being stingy here.
Was the one you received as per Image?
It's just like it looks in the picture - w
Was the installation difficult?
I have an electric Impact wrench, so the work was easy and effortless. The screw lock fluid is TL22J made by 3M (see photo).
How was your experience with it?
After about 1000 km after installation, I have no problems so far.
[Included Parts:were they on?
No, there is not
[Was there anything that disappointed you?
Not at all, but if the price was a little lower.... . w
Other items that would be helpful
Points to note for installation:The bolt that holds the disc rotor in place is tightened very firmly. Also, when installing a new Rotor, it is very dangerous to apply Screw lock fluid to the Bolt and tighten it with Torque Control! "Important safety parts" Don't forget that it is!
Availability and clarity of Instruction Manual:Please refer to the paper included in the Package that describes the Measurement and the encouraged tightening Torque.
Items to be prepared together:Impact wrench, Screw lock fluid, Torque wrench.
View detail
Half the price of OEM
It had not been replaced for a long time, so it hardened and lost its damper effect, so it was replaced for refresh!
I was quoted to buy OEM, but it cost twice as much as KITACO product, so I decided to buy KITACO product.
I am Large satisfied with this one because it is cosier!
View detail