Reviews
Performance and price are sufficient for your needs.
[How is it used?
Used to disassemble and clean the rear master cylinder of a YAMAHA XJR400R.
How was your experience with it?
Nothing is impossible.
I believe that the basic performance of these products will remain the same.
How did it compare to other products?
This item is 1 bagQuantity:1 Set of 2pcs. but other products are available in Large quantity and cheaper.
However, DailyMechanic like me only uses it occasionally, so I think this one is sufficient.
[Points to note]
If Torque management is not done properly, Brake fluid will leak and ooze, so be sure to do it properly.
View detail
Offset firmly in place.
[How is it used?
I used it when I changed the Silencer on my YAMAHA XJR400R from MotoGEARΦ100 to K2tecΦ86.
The Φ14 thinner Silencer band is now farther away and cannot be handled by the existing Bolt.
So we measured the amount of gap and purchased this product to offset the aluminum collars on the rear suspension mounting and silencer band side.
How was your experience with it?
The measurements were perfect and the Offset was solid.
We also did a good Torque management on the fixation, so I don't think there is any problem.
How did it compare to other products?
It was Large strange to find a product that fits Exactly because various Manufacturers are offering similar products.
I have the impression that this product had the best price and Size development.
You can buy them at Home center, but basically you should buy them at motorcycle supply stores or on the webike.
I think it's good
[Points to note]
nothing special
View detail
for adjustment
Repurchased to add a step on the Screen I had previously put on. View detail
Buy Bore Up Kit for Repair!
[How is it used?
The Clip that came with the Bore Up Kit contained only the minimum necessary and was insufficient during maintenance, which led to its purchase.
How was your experience with it?
BALI is a concern, but if it is used with BALI removed as described in the Instruction Manual, it can be used without problems.
How did it compare to other products?
It is more difficult to fit than the e-type Pin from Mukawa or Clipping point, but I think Orthodox is more stable and less likely to come off.
[Points to note]
If it fails, it will fly away and you will not know where it went.
I think it would be tough to take it out once it is inside the Crankcase.
▼It seems that inventory is running low, but if it goes out of use, maintenance will not be possible.
It would be sad to see Repair Parts become a valuable part of the old car category any longer.
View detail
Universal and can be used in many ways
[How is it used?
The bar of the external Rear Sets was not long enough, so we put it on to extend the length.
I personally prefer longer ones because they are easier to load.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy to insert between Footpeg and Footpeg Plate.
How was your experience with it?
It serves its purpose because it is used as a simple color.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
It's just a color of Aluminum, so it could be a little cheaper. I thought it was a good idea.
but it is good to have a variety of Sizes to choose from.
View detail
Exactly!
This time, I had to buy it in a hurry because the Carrier RANBolt I was installing had come off and was missing.
I was just about to add a screw lock material, but the other side was still there, so I measured the size and purchased a bolt at a nearby home center!
Screw lock material was also added!
View detail
Racer vehicle to public road Spec. return
[How is it used?
I purchased the Racer vehicle to restore the Headlight Wiring as it had been cut off.
Quantity as there are two lights in the H4Type Headlight.:2pc. I bought a set
Was the one you received as per Image?
Photo
Was the installation difficult?
Installation can be done quickly if you have a certain degree of Wiring processing skills.
I couldn't work with regular Electric Works Pliers when I was cranking, so I used Radio pliers.
However, The top is for Earth, right? Check the wiring diagram carefully beforehand.
The connector is also securely fastened so that it will not accidentally come loose.
How was your experience with it?
Of course, as long as the Wiring is solid, there is no problem at all in lighting the Headlight.
It also engages well with the Valve of Headlight and does not seem to come loose.
[Included Parts:were they on?
It comes with a Connector and the required number of terminals.
[Was there anything that disappointed you?
Not particularly
【Review】
It is good for those who make their own wiring around the headlight and for repairing old OEMs.
The terminals do not come with spare parts, so install them carefully to avoid mistakes.
View detail
Stainless Steel anxiety and cleanliness are at odds with each other.
We decided to paint the hubs on the Yamaha car, and since we were going to do that, we also made new Disc Rotor Bolt.
Material:Although I was a little concerned about the strength of Stainless Steel, I couldn't help but be attracted by the fact that Stainless Steel is resistant to rust, and so I decided to purchase it.
In the past, I had heard that stainless steel has lower strength against shear stress than steel or Chromoly, so I avoided using it where large forces are applied perpendicular to the bolt.
The Disc Rotor Bolt and Caliper Mount Bolt are just that.
However, since KITACO has been selling this product for many years, we decided to use it this time because we thought it would not cause any problems and we do not have the skills to do Race or Hard Breaking.
I would like to check it regularly and see about durability.
View detail
Easy to use
I bought it because I couldn't find it at my favorite store and there was just a Point.
It is easy to use, but the rubber rubber doesn't last long because it is used in a place where it is bent many times.
We purchased several in stock as consumables.
View detail
Used to reduce rattling of Brake lever
[How is it used?
Brake lever was rattling badly and I bought it in hopes that it would get better.
The Touch feeling of the MASTER itself was not so good, but I suspected that maybe it was because the rattling was so bad that I could not press the Piston straight? I also suspected that it might be because I could not press the Piston straight.
To be honest, since it is a SmallEngine Displacement Volume for a foreign car, I thought that the rattling might be terrible combined with poor accuracy, but I tried it when I learned from an article on Webig that this Washer can reduce the rattling.
Was the one you received as per Image?
As you can see in the picture, it is just a Washer.
It is not a very expensive product, but the price of this thin Washer may be too expensive for some people...
Was the installation difficult?
Simply remove the Brake lever and insert it in between.
Washer is just on Lever, so it is a bit frustrating to have to Gap it back to MASTER.
How was your experience with it?
Actually, I first tried 0.3mm, but did not feel much change. 0.6mm with 2 layers of 0.3mm reduced rattling in a good way. However, I felt that the movement of Lever was a little reluctant or stuck, perhaps due to the two layers of 0.3mm, and I felt it was dangerous.:I settled on 1pc. Even with 0.5mm, there is some rattling, but it has been reduced to an acceptable level.
However, I did not see any large change in the touch feeling that I had expected, and I felt again that in such a case, I had no choice but to replace the entire MASTER.
[Included Parts:were they on?
Washer only.
[Was there anything that disappointed you?
nothing special
View detail
Fixing Screw
I bought it to try it out, wondering if it could be used to fix Cowl. The materialAluminum was nice, but the tapping screw and the length of the screw seem to limit its use.
It would be helpful if you could sell regular Screws, available in a choice of lengths.
View detail
Bolt cover
Bolt, installed for protection purpose to the Nut.
It seems to be a little hard plastic and is hard to remove after installation.
Quantity:1 Set of 3pcs., the price is not that much and it will look a little better.
View detail
Bolt cover
It seems to be good for Screw head protection and One point dress-up.Quantity:1 Set of 3pcs., Plastic, slightly stiff.
Installation is fine, but when removing it, it almost cracks.
Lack if you force it off, the color will peel off.
The price is not that much, though, so I would just buy it again.
View detail
Hexagonal hole accuracy not good enough, soft?
Hmm.
It is delicate to say the least. The hole itself is shallow because it is a low-head bolt, but if you tighten it with the specified torque, the tool will bite into it and the hole will be star-shaped.
I don't want to think about when to remove it. LOL.
Stainless looks good, but what is the cosmetic value in terms of total? Total?
View detail
Struggled with the hardness of the crimp
I didn't want to use the interrupt terminal that came with my CRF250M to install the Plasma booster, so I used it to create my own Wiring.
The female terminal could be crimped without any problem, but the crimping point on the male side was too thick for the crimped pliers with thin handles, so we purchased additional crimped pliers from Emon. Although the shape was slightly distorted, I was able to crimp it and install the Plasma booster itself without any problems.
I was able to purchase this product with confidence because there are different sizes of similar Plain Type Terminals, so I searched for Ignition Coil Terminals and found this product.
I don't know if it was a simple lack of power on my part or if I needed a special tool for thicker plates, but I was able to get by with large crimped pliers with thicker handles.
CRF250M is a single cylinder, so one is also safe as a spare.
View detail
ScrewCover
The screws near the Exhaust System interfere with vibrations and cause scratches, so I bought this to try to protect and prevent scratches.
The colors are vibrant, not bad looking.
Quantity:1 Set of 3pcs., the installation seems to be a little stiff and difficult to remove.
View detail
Purchased for Wiring
This time, I needed to do Wiring for Circuit.
Purchased
The strength of the product is also solid and problem-free.
View detail
Purchased for Wiring
This time, I needed to do Wiring for Circuit.
Purchased
The strength of the product is also solid and problem-free.
View detail
Quantity:It would have been better if it was 1 Set of 4pcs,
I purchased the 4mmSize Rivet because I needed it when installing the MC21 Screen.
What I wanted was 4 pieces, but the Quantity:I bought two because it was 1 Set of 3pcs.
There are two different lengths of 4mm Nylon rivets from KITACOConvenienceParts, and I was not sure which one was better. There are two types of rivets with different lengths, and I was not sure which one was better, If it's a scuzzy one, why not just put a Washer on it?" I bought this one because I thought it was perfect.
OEM Parts are still available, so if you are concerned, OEM Parts are the way to go.
I am satisfied with the price, which was less than the cost of four OEM parts.
View detail
Bolt replacement for MirrorOffsetHolder
Currently, I am using the low type of DAYTOMA's Hi-Viz Mirror and the shorter version of Tanax's Mirror Offset Holder. It is not impossible to fasten the OffsetHolder with other items, but it was not good for my mental health, so I decided to replace it.
However, I have never seen a 1.25 cap bolt, which is often used for motorcycles, at a home center, and I have to order one from a shop specializing in screw bolts by mail order. You have to order from a shop specializing in screw bolts by mail order, or buy from KITACO or Posh. In this case, I only needed to purchase two bolts, and since I did not have any other bolts or nuts that I needed, and since I was not Timing for bulk purchases, I chose KITACO's products instead of ordering from ScrewShop because of the shipping cost. I wanted a black one, if possible, so I hesitated between a black one and a black one from Posh, but I decided to buy a KITACO product because it was a little bit cheaper. The bolt itself is a good product that can be used normally without any problem, but I think the price is too expensive.
By replacing the Bolt with a 5mm longer Bolt, the Bolt is now firmly in place and secure. We recommend replacing the bolt with a new one if you have similar concerns.
View detail