Reviews
520Conversion Demerit
It is cheaper than collecting OEM parts, and as you all know, there is a Merit to make the 520. However, the Noise when driving will be Large.
It sounds like the sound when the bottom of the teeth of the front sprocket (Driven Sprocket) hits the Roller of the Chain.
The OEM Sprocket has a Ring-shaped anti-vibration Rubber, which reduces Noise.
As a countermeasure, I had some DAYTONAInsulation Glass WoolSeat left over from a previous purchase at Webig, so I attached this to the inside of the Sprocket Cover.
As an effect, Noise became much smaller.
View detail
Why is the same number of Ding as OEMs so expensive….
What made you decide to buy?
I have been working on the ZX-6R for 3 years now, and the mileage is about 10,000 km. I thought it was too early to replace them, but since all the parts were available during the spring sale, I decided to replace them.
[How was the installation?
I found information that the Torque of the Engine Sprocket nut fixing the front sprocket was halfway tight, so I loosened the Engine Sprocket nut using an electric Impact wrench from Tirefor Replacement. After that, I tightened the rear brake with the torque wrench at the specified torque of 147Nm, and finally, I bent the washer over the nut using the water pump pliers to prevent it from loosening.
*We are planning to describe this replacement work in our maintenance diary. Please take a look if you like.
How was your experience with it?
At first I was not sure whether to go with 16T or not, but I liked the ride quality of the OEM, so I decided to go with 15T, the same as the OEM. So there was no change between before and after the replacement. The normal specifications list on the product page says 16T, but the 21-year ZX-6R has 15T Front, 43 Rear, 2.866 reduction ratio, and 112 Chain links.
View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
The cb750...
WeBig has always been a great help to us.
Thank you very much for your cooperation from now on.
View detail
520Conversion
Chain, I purchased this item from Timing on Sprocket exchange.
The secondary deceleration ratio is now about 2.7, and I can drive Smoothly without feeling a lack of Torque during acceleration. (At first it felt strange when starting off, but once I got used to it, I prefer it this way.)
View detail
Fits: KAWASAKI ELIMINATOR250SE, KAWASAKI ELIMINATOR250, KAWASAKI ELIMINATOR250LX, YAMAHA YZF-R3, YAMAHA YZF-R25, KAWASAKI ELIMINATOR250V, KAWASAKI ER-5, KAWASAKI FX400R, KAWASAKI GPX250R II, KAWASAKI GPX250R, KAWASAKI GPX400R, KAWASAKI GPZ250R, KAWASAKI GPZ400R, KAWASAKI GPZ400S, KAWASAKI Ninja250, KAWASAKI Ninja250SL, KAWASAKI VERSYS-X 250, KAWASAKI Z250, KAWASAKI Z250SL, KAWASAKI ZEPHYR400
exchange
I bought this for a ZZr250 Rear Sprocketfor replacement, it is lighter than the OEMSprocket and looks better in Gold. It is an applicable product and I was able to install it without any modification. View detail
Fits: KAWASAKI Ninja1000, KAWASAKI Ninja1000SX, KAWASAKI Ninja650, KAWASAKI VALCAN S, KAWASAKI VERSYS1000 SE, KAWASAKI VERSYS650, KAWASAKI Z H2, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI ZX-25R, KAWASAKI ZX-6R, KAWASAKI 750Turbo, KAWASAKI ER-4n, KAWASAKI ER-4n, KAWASAKI ER-6f, KAWASAKI ER-6n
Stable SUNSTAR
I was not sure about BlackSteel, but I decided that lightness is justice.
I changed from 43T to 42T, but since it is Rear, I don't think it changes anything experientially.
Next time I will change Front as well and see how it goes.
View detail
Fits: YAMAHA NIKEN GT, YAMAHA NIKEN, YAMAHA XSR700, YAMAHA MT-10 SP, YAMAHA MT-10, YAMAHA XSR900, YAMAHA YZF-R1M, YAMAHA YZF-R1, YAMAHA MT-09SP, YAMAHA MT-09 TRACER GT, YAMAHA MT-09 TRACER, YAMAHA MT-09, YAMAHA MT-07, YAMAHA FZ8S, YAMAHA FAZER8, YAMAHA TDM900
Optimized with Front1Down
[How is it used?
This is an IMPRESSION with 100% Circuit running.
Was the one you received as per Image?
Yes.
This time, we dared to choose 525 without 520Conversion, but even though Steel is the same as OEM, it is MADE IN SUNSTAR. (OEM may be SUNSTAR as well.) is lightweight due to the lack of meat removal and the RubberDamper, which is present on the OEM.
Was the installation difficult?
The shop is in charge of the front replacement, so the process is basically to loosen the axle of the rear wheel, lower the tension of the chain, and then remove and install the front sprocket. The front sprocket nut has a high torque of 140Nm and the OEM is very tight, so it may be difficult to remove the front sprocket without a proper tool.
How was your experience with it?
The OEM YZF-R1/M has a secondary reduction ratio of F16/R41, but even in Circuit, it rarely goes into 6th gear, and most people change it Large. Most people change the ratio to a large one. Unless you want to adapt it to a specific Circuit, it can run in any Circuit to some extent.:As for the Set, I think Front1Down is the best solution, running with the OEM GEAR ratio, In second gear, it's hard to ride at high rpm, and in third gear it's a little heavy." You can drive comfortably in 3rd gear on the Point where you feel like you are in the middle of the road. The appearance does not change at all, but expensive Parts (Exhaust System, Suspension, etc.) I think it is more expensive and outstanding than replacing the
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
A new pure STD Nut is required for replacement. I also replaced the Washer, which is in the form of a plate, at the same time.
・90208-22002 Washer、ConicalSpring ¥616 (Tax included/as of April 2024)
・90179-22018 Nut ¥660 (Tax included/as of April 2024)
The two points are
View detail
![TRAD Type1[Trad type1]Front disk rotor](https://img.webike-cdn.net/catalogue/images/100295/T-21HZ_1_TS.jpg)
Fits: KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 900 Super Four, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750SS MACH IV, KAWASAKI 750RS, KAWASAKI 750RS, KAWASAKI 650RS
To Refresh Disc Rotor
I purchased this for use with my Kawasaki Z1.
I purchased this disc with HoleType because the OEMDisc Rotor was approaching its wear limit and I wanted a custom look.
When we removed the STD Disc for replacement, we found the difference in weight between the STD Disc and the Hadrill.
Along with braking power, we expect the weight difference will also change the driving experience.
Rotor replacement is not a difficult task if done carefully.
The bolt hole where the rotor bolt was removed was lightly cleaned with M8 fine tap, Locktite Blue was applied to the bolt, and the bolt was fastened at 26 N.m.
Pad should also be replaced with a new one.
View detail
Fits: YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200, YAMAHA TW125
feel well
Used for Restore on TW200
It is a little more expensive than other manufacturers, but I trust them.
The one that came with it so far was terrible.
In case of TW200, it is necessary to remove the Left cover to replace the FrontSprocket.
I'll have to buy Packing at the same time.
View detail
Fits: YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200, YAMAHA AG200, YAMAHA TW125
A little tainted.
Used for Restore of TW200
I bought it to go along with the Front that I also replaced.
Maybe it didn't have to be Duralumin.
Well, I bought it.
The items are clean and trustworthy.
View detail
Fits: KAWASAKI GPZ900R
SUNSTARFront & Rear Sprocket & Chain
We chose Black gold to match the car body color.
The Drive/Driven was also replaced and the push/pull was lightened.
Sustainable, safe, and largeup.
View detail
Fits: SUZUKI VOLTY, SUZUKI ST250, SUZUKI ST250 Etype, SUZUKI GrassTracker, SUZUKI GrassTracker BIGBOY
Front sprocket replacement
Changed Front from 14T to 16T and Rear Sprocket from 48T to 46T.
I thought it would be sluggish at the start because the GEAR ratio was quite low, but I don't mind that much.
It is easy to handle for long touring and city driving.
View detail
Fits: SUZUKI GSX250R, SUZUKI SV650, SUZUKI SV650X, SUZUKI V-STORM250, SUZUKI ACROSS, SUZUKI BANDIT250, SUZUKI BANDIT400, SUZUKI BANDIT400V, SUZUKI BANDIT400V, SUZUKI BANDIT400VZ, SUZUKI BANDIT600, SUZUKI BANDIT600S, SUZUKI BANDIT650, SUZUKI DESPERADO400 WINDER, SUZUKI DESPERADO400 X, SUZUKI DESPERADO400, SUZUKI DESPERADO800, SUZUKI DESPERADO800X, SUZUKI GLADIUS400, SUZUKI GLADIUS650
Rear Sprocket replacement
Changed Front from 14T to 16T and Rear Sprocket from 48T to 46T.
I thought it would be sluggish at the start because the GEAR ratio was quite low, but I don't mind that much.
It is easy to handle for long touring and city driving.
View detail
Fits: SUZUKI RG500 γ, SUZUKI SV1000, SUZUKI GS400, SUZUKI GS1200SS, KAWASAKI Z400FX, SUZUKI DESPERADO800, SUZUKI BANDIT650, KAWASAKI ZZR400, SUZUKI RF600R, SUZUKI INAZUMA1200, SUZUKI GSX-R750, YAMAHA YZF600R ThunderCat, SUZUKI BANDIT1250S, SUZUKI GSF1200, SUZUKI BANDIT1200, SUZUKI BANDIT600, SUZUKI GSX-R1000, SUZUKI GSX-R600, SUZUKI GSX750 INAZUMA, SUZUKI GSX750S KATANA
It works without any problems.
Replaced at the same time as Chain.
After the replacement, I do not notice any change, but it seems to be working fine.
View detail
Fits: SUZUKI BANDIT1200, SUZUKI BANDIT1200S, SUZUKI GSF1200S, SUZUKI GS1200SS, SUZUKI GSF1200, SUZUKI GS1000, SUZUKI RF900R, SUZUKI GSX-R1100, SUZUKI GS1100ES, SUZUKI GSX1100F, SUZUKI GS1100EF, SUZUKI GSX1100S KATANA, SUZUKI GSX1100E, SUZUKI GS750, SUZUKI GSX750SKATANA, SUZUKI GSX1000SKATANA
We chose Stainless Steel for its durability.
I think Sprocket is still SUNSTAR.
I chose Stainless Steel for its durability, and I am glad I did.
We have driven the car and have not experienced any problems.
View detail
Fits: HONDA HORNET, HONDA JADE, HONDA VTR250, HONDA VTR250F, HONDA V-TWIN MAGNA250, HONDA VTZ250, HONDA XELVIS
For CB250F
About quality and texture Excellent product About the feeling of use smooth running.quality is good. About shipping and packaging good packaging and fast shipping View detail
Fits: KAWASAKI Z900, KAWASAKI Z900, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS
Diversion to ZX25R
The SUNSTAR set for ZX25R is the same diameter and thickness, but not enough, so it was diverted.
Not compatible, but can be installed only by using Spacer collar (5mm).
The 310Φ4.5mm→320Φ5.0mm change increases the weight to 1300g→1430g.
I had hoped that the weight of the inner housing would be reduced to aluminum, but the weight has increased by about 130g.
If you want to use it all the way to the edge, you need to adjust it with Shimetc.
The texture is much better, but Fee Ring did not feel any difference on about public roads.
View detail
Fits: HONDA V-TWIN MAGNA, HONDA CL400, HONDA CBX400F, HONDA CB400SS, HONDA STEED400, HONDA STEED600, HONDA CBR500R, HONDA CB400FOUR, HONDA VFR400Z, HONDA VRX Roadster, HONDA XRV750 AFRICATWIN, HONDA VF1000R, HONDA VF400F INTEGRA, HONDA VFR400R, HONDA VF750F, HONDA VF400F, HONDA VF1000F, HONDA VF1000F interceptor, HONDA CBR400F, HONDA STEED400
520Conversion
Conversion520 from 530. It is easier to push and move. View detail
Fits: HONDA HORNET, HONDA JADE, HONDA VTR250, HONDA VTR250F, HONDA V-TWIN MAGNA250, HONDA VTZ250, HONDA XELVIS
Great
About quality and texture Good Product. light weight. About the feeling of use good for the smooth run. About shipping and packaging Fast Shipping. package is well no way to damage View detail