Reviews
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS), KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS)
first exchange
I replaced a Rubber that probably had never been replaced since it was born.
Just by getting on the footpeg, the squishy feeling is gone and I can step on it firmly.
I am happy with the footpeg position back to normal. I'm already using Quantity:2pc. I am going to buy a Set and replace the Rubber on the Right Sidefootpeg as well.
View detail
Excellent finishing touch to my bike
This fork cover is just like the ones fitted to the old bikes back in the day. Fitting is super easy and is a five minute job, then stand back and admire how the ugly horn is now covered up with a lovely shiny chrome cover with Kawasaki in the original script..just like it should be! The price was very reasonable and quality high. Shipping to UK was good too - inside two weeks via standard Japan post. Well done Webike! View detail
I'm on JC92.
It is diverted for Z900RS.
The O-rings are sufficient.
I look forward to comparing this in mid-summer and mid-winter.
In the middle of winter, it feels like it's probably only getting up to about 60 degrees.
With this attached, it will be properly managed.
View detail
Fits: KAWASAKI Z900RS CAFE, KAWASAKI Z900RS, KAWASAKI Z900RS CAFE, KAWASAKI Z900RS
Tuck Roll Seat for Z900rs DOREMITail
[How is it used?
Currently in use
Was the one you received as per Image?
The design is different from the Image image, but the design has one point such as Rivet, and I am satisfied with the Large change.
Was the installation difficult?
Installation is easy:a Tandem belt is included and the mounting holes need to be drilled with Drilletc.
How was your experience with it?
The same spec. as the Normal seat, so it can be installed with in-vehicle tools without any problem.
[Included Parts:were they on?
Tandem belt was included.
[Was there anything that disappointed you?
None in particular:??
Other items that would be helpful
The cosmetics are good in every way.
The fittings are superb, as they are for DOREMI's Tail.
The thickness is different from for STD Tail and there is less Damage to the buttocks. In addition, it is especially recommendation for those who want to put KAWASAKI letters on Z1Type Club bar or Seat.
View detail
Quantity:Pair (for Left and Right) Balance is difficult.
[How is it used?
Used for a dress-up, attached to a Leopard single seat cowl and the sticker dimensions look good.
Was the one you received as per Image?
I thought there was a cutout on the protective seal surface, although it was as shown in the Image.
Was the installation difficult?
Quantity:Pair (for Left and Right) It is difficult to put it on with good balance.
How was your experience with it?
Good for easy dress-up.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
As mentioned above, the LineSticker Seat itself is a transfer type, but there is no cutout on the protective seal surface or the backing paper, and having to cut along the MustacheLine was disappointing.
(Point of installation or hang)
Temporarily fix and paste with good balance.
(Instruction Manual) No
(Caution) Material that may contain both air bubbles and wrinkles if not pasted in one shot.
Opinions and requests to Manufacturer
It would be helpful if the Mount and Protective Seal have a cutout along the Line.
View detail
Always believable DOREMI
I always buy DOREMI products because I believe in technology.
Again, it was a Large hit, and I was more than satisfied with my expectations.
Replaced old Harness with new Harness and no electrical trouble.
It's been running fine so far.
View detail
Casually Fashion
Select the Large character.
Inlaid letters are glued from the back for peace of mind.
It is a pricey product but Horn's blindfold effect was good.
View detail
CAFE requires additional Bracket
Installed on Z900RS CAFE
CAFE cannot be installed without an additional Bracket.
I found just the right Bracket at a nearby Home center.
We took advantage of that and installed it.
Quantity for Vertical:2pc 1 pc for horizontal
Quantities bought at the root of Optical Axis Adjustment Bracket:The two brackets are vertically tightened together, and another short bracket with a long horizontal hole is attached horizontally under the bracket, and then DOREMI's bracket is attached to the bracket to create a center.
If I recall correctly, Horn's Bracket also needs to be displaced.
It takes a little time and effort, but it is fun to install through trial and error while thinking about it.
Right now we are installing DriveRecorder's FrontCamera on DOREMI's ForkEmblem's Bracket.
The image was blurred due to vibration when the car stopped, so the upper part of the optical axis bracket and the ForkEmblem Bracket were fixed vertically with an inHemp palm.
The appearance of the FrontCamera is perfect without being too noticeable.
View detail
Hidden by Sub-frame
It seems to be normal for air bubbles to be present, perhaps to prevent expansion and cracking due to temperature.
It is not possible to read the needle in detail while driving, but can be determined by the position of the needle on the Large body.
However, as you can see in this picture, the sub-frame gets in the way of the view when it is in the riding position.
You can barely read it as if you are embarking on a Right.
View detail
It could have come with OEM.
Levels that could have been included in the OEM
As it is, it is embarrassingly unseemly, so it is a standard DOREMI.
View detail
Large letters in Plating
I wouldn't use it if it had DoubleHorn all over it like Honda does, but it's a ManufacturerNORMAL.
I would like to see this type of thing installed.
It looks dumb without it. Personally, I think Plating is better than Black.
CAFE seems to have a different Bracket. They said that if it is not attached on the lower side, it will interfere with Cowl.
It would be normal to have this.
View detail
Fits: KAWASAKI ZEPHYRX, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400
It sticks well without processing:??
Installation is very easy:??
Looks a lot better Parenthesis ??
Recommended for an introduction to Custom. It is cosmetically good. ??
View detail
The purpose is to dress-up
I do not intend to control the oil temperature, but to dress-up the oil. In that sense, I am satisfied with the product as shown in the Image. I have only driven about 200 km, but there are no oil leaks as described by others. By the way, the temperature display was about 90-100℃ in winter (I don't know if this is correct or not). View detail
Fits: KAWASAKI Z900RS, KAWASAKI Z900RS CAFE
Satisfied
When fitted, the atmosphere is completely changed.
If you are looking for luxury, this is an excellent choice.
View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z2 (750RS)
Horn switch dead…
I tried to get two of the OEM Product, but the internal parts were made differently (poorly) to begin with, and I gave up on them as soon as I opened them up. It seems to be a hit or miss situation. View detail
I think it's good
I would like to know which is the best product for many of the same items. This item itself is not bad. safe View detail
Fits: KAWASAKI Z2 (750RS), KAWASAKI S1C, KAWASAKI S1B, KAWASAKI S1A, KAWASAKI KH500, KAWASAKI KH400, KAWASAKI KH250, KAWASAKI H2C, KAWASAKI H2B, KAWASAKI H1F, KAWASAKI H1E, KAWASAKI H1D, KAWASAKI S3, KAWASAKI S2A, KAWASAKI S3A, KAWASAKI W1SA, KAWASAKI W3, KAWASAKI Z1, KAWASAKI Z1000, KAWASAKI Z750
From z-type OEMBracket to DOREMI made Short
I changed from z1z2 OEMBRACKET to Short Bracket. z1z2 OEMBRACKET is good, but I changed to Short Bracket because I thought Short Bracket has better balance because I narrowed down the width of Handlebar.
There is nothing wrong with the installation with the combination of OEMBlinker and DOREMIBracket.
Once the wiring is pulled out of the OEMBracket, it may be difficult to pass the wiring through the small hole in the OEMBracket.
DOREMI's bracket has a large wiring hole for easy installation.
Plating quality is not bad and I think it is a good product because I think the price is reasonable.
View detail
Nice piece
Very nice Doremi quality piece perfectly suited for my anniversary Z900 RS. Assembly without problem, you just have to remember to order a new seal for the cover. -------------------------------------------------- -------- Very nice Doremi quality piece perfectly suited for my Z900 Rs Birthday. Mounting without problem, you just have to think about ordering a new seal for the lid. Powered by Google Translator View detail
I love this because it has a classic feel to it
I'm a Korean. I ride a Honda cb1100ex. A very good analog thermometer for use on bikes with air-cooled engines. The design is pretty and the function is faithful. You can check the temperature of the engine when warming up or taking a break in between. I recommend it. -------------------------------------------------- -------- I'm a Korean. It is riding Honda's CB1100EX. It is a very good analog thermometer for use in bikes with air-cooled engines. The design is also pretty and faithful to the function. When you preheat or take a break in the middle, you can check the temperature of the engine. I recommend it. Powered by Google Translator View detail
Fits: KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750FX, KAWASAKI Z1 (900SUPER4), KAWASAKI Z1-R/Z1-RII, KAWASAKI Z1000, KAWASAKI Z1000 MkII, KAWASAKI Z2 (750RS), KAWASAKI Z750FX
Installed on TT-R125LWE.
Screw diameter is thinner than the resin type and the position can be adjusted finely.
I selected this product.
The bracket was also cut by hand from an aluminum plate and made one-off.
View detail