Reviews
Mellow SmokeSilver
Mellow Smoke is difficult to see due to the reflection on the inside, so the inside is darkened. [Color] Smoke might be better.
I thought I had been gently wiping water droplets off with Towel after normal maintenance and after using it in the rain a few times, but the plating is peeling off and it is hard to see these days.
Very Delicate Plating.
It did not last a year.
View detail
Fits: SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy
meticulous manufacturing
It was good up to the point of installing the Coupler on the body side of the NORMALIndicator with the Coupler, but the remaining Black color code was installed with Tap for Connection and the Instruction Manual's Sky blue code. The sky-blue code is used to connect to the Quantity:There are 2 pcs and the first connection failed, but I opened the Tap and connected it to the dark sky blue cord and it lit up fine. View detail
Fits: SUZUKI V-Strom650 L2, SUZUKI V-Strom650, SUZUKI V-Strom650 XT, SUZUKI DL650 V-Strom, SUZUKI V-Strom650 L2 XT
Engine Guard installed
Installation should not be a problem if you have some knowledge of maintenance.
An Engine Guard was added to protect the engine in the event of a runaway and to mount the Fog Lamp.
View detail
Bolt hole in rear sprocket is Large
It is cheap and good, but the only thing that bothers me is that the Bolt hole on the Rear sprocket is Large. I'm worried that it might move during use. View detail
Clean. Dirty. Vivid.
Description used only in DOT 4.0 and 5.1.
5.0 (Silicon-based) not used
[How is it used?
Continuous use from July 18, 2021 to April 21, 2024
・71,299 - 59,896 = 11,403km
Urban, Touring, and Circuit driving events
YZF-R6Front side
Master Cylinder side is R6OEM
Fluid tanks are available from Kawasaki (https://www.webike.net/sd/21984592/)
I think Clamp was something from K-CON.
Fluid Transparent DOT5.1 (https://www.webike.net/sd/24515708/)
FluidBlue (https://www.webike.net/sd/24038239/)
FluidGreen (https://www.webike.net/sd/20443936/)
FluidRed (https://www.webike.net/sd/21585702/)
Was the one you received as per Image?
As per Image with Simple Package, first found in Naps and now also in LycoLand.
Was the installation difficult?
The hose itself is fairly easy to insert after loosening the clamp and removing the original hose by tearing it open. However, it is a little bit large to insert the hose without wetting the inside of the hose with Fluid or something.
Air venting is required for modification of the brake system, so there is some time and effort required to vent the air.
How was your experience with it?
・ [Color] When we say ClearTank. [Color] Unlike the Smoke Fluid Tanks, it is completely [Color] Clear shows the Fluid color beautifully.
Although the Image was less durable than the Black Hose, it is still in use with no rips, cracks, or tears.
The Fluid is not blotchy like the non Fluid-compatible Hose, which was my biggest concern, and the word "Fluid-compatible" is true.
The color of the Fluid is so clear that the yellow tint of the Fluid is very obvious.
Especially with blue Fluid, it takes less than a year for the color to become the color of Tokyo Bay, although it is beautiful immediately after the replacement. (Replaced more than 4 times in 3 years of use)
The transparent design makes it easy to see the climb when injecting from the Caliper side.
The product is relatively new, so even Motorcycle shop owners are not familiar with it. Is this Fluid-enabled?" The situation arose where people asked me "What do you mean?
The feeling of operation cannot be evaluated independently because the Fluid is being replaced at the same time, but I am sure there will be no problem because I can use it without feeling any discomfort.
The Red was probably too bright a red to match the Blue/Silver Motorcycle, and I didn't have a picture of it because I replaced it too quickly.
[Included Parts:were they on?
Hose only, Clamp not included
[Was there anything that disappointed you?
None, as the Fluid colors are nicely recognizable and the durability and feel of the product are absolutely fine.
Although it was unexpected that the discoloration caused by Fluid degradation was too obvious, it is inextricably linked to the desire to clearly distinguish the color of Fluid.
[ITEMS TO BUY TOGETHER
Hose clamp and for ReplacementFluid
DAYTONA's Black Clamp rusted quickly, so K-CON is recommended.
The price is not that different from Black's Hose, and the feel is perfectly acceptable. The increase in replacement frequency due to appearance is not a bad thing when it comes to performance.
Degradation of Fluid [Color] A fun product to add to your selection if you can accept that it is more sensitive than ClearTank.
View detail
(after neg. verb stem) had better (verb)
[How is it used?
I bought this product to prevent my helmet from being stolen when touring or going out.
I used to not have a Helmet lock, so I had to carry my Helmet with me when I got off my Motorcycle.
I was always worried about hanging it on Mirror because I think it is easy to be stolen.
Was the one you received as per Image?
KITACO
KITACO in the world
It's in a clear bag.
Quantity:2pc keys are included, so even if you lose one, you can rest assured that you have another one!
Was the installation difficult?
May be difficult for beginners
All the Rear cowl has to be removed, so if you have never removed a cowl before, please do so carefully.
If too much force is applied, the plastic part is prone to cracking.
The bolt on the Tandem Footpeg is coated with Screw Lock, so it was a bit odd to remove the Bolt Large, but it is not impossible to remove.
How was your experience with it?
I was attracted to this product because of its mounting position, so it is not very noticeable and I think it is very beautiful.
I think the recommended point is that it is the same color as the bright black Tandem Footpeg, so it does not disrupt the balance of the entire vehicle.
However, I have no problem because I have a 1 pc exhaust system, but if you use the OEM Dual Exhaust System, the helmet will come in contact with the exhaust system, and if you apply the helmet when it is hot, the interior of the helmet may melt, Be careful!
[Included Parts:were they on?
Key Quantity:2pc
Quantity:Note that if you lose both 2pcs, you are finished!
[Was there anything that disappointed you?
OEMExhaust System may not be so easy
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Recommended for a single-pipe Exhaust System!
View detail
We use it for our cars
I use it in my high ace Regis car. 12v is the same as motorcycle, so there is no problem. Minus terminal is an appropriate bolt that can be used for earth measurement. The Minus terminal is a suitable bolt that can be used for earth.
I use it on my iPhone12mini and it charges by turning the key on and also by Idling, it does not charge when the Cell is turned on but it will come back on soon. The charge increases even when using the iPhone as Navigation, watching Youtube, or using Bluetooth to connect to other devices. Naturally, it charges faster when the screen is dark or when the app is not in use.
I am using this Charger in my motorcycle BALIUS2, but I can't charge the battery near Idling due to lack of power.
The problem is that the phone becomes loud and unusable when exposed to warm air from a heater or when not exposed to cool air from an air-conditioner under the blazing sun in mid-summer, instead of charging. Also, the location of the charging pad on the phone has a significant impact on the performance of the device. The purchaser should find out where the charging pad can charge the phone the fastest.
View detail
Just the right Size for Motorcycle
Similar products were not purchased because they were too large for motorcycle use (10L, etc.) or too tall to fit underneath.
The 4L capacity is sufficient for Motorcycle and may be used for light cars.
The photo is of a Z900RS, but it is lower in height and easier to install than a littering pack or something like that.
In similar products from other companies, the cap is often damaged by oil and cracks, but this one seems to be large and sturdy because it contains packing.
Since there was no Net at the receiving end and Bolt was in danger of falling in, a suitable net was installed with glue.
The receptacle is shallow, and if the ejection is too vigorous, it may fly out.
View detail
Fits: YAMAHA YZ125X, YAMAHA YZ250F, YAMAHA YZ250X, YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ426F, YAMAHA YZ450F, YAMAHA YZ80, YAMAHA YZ85
It may be a classic.
I bought this one because a certain lever that does not break interferes with the CloseHand guard on a 4Finger. If you care about the appearance, you should choose the cut-out type, but if you don't want it to break during the race, you should choose the Forged Type.
The exterior is of high quality, as one would expect from Zita. Installation is a simple and easy process. Adjustment is stepless, but requires a tool, so it is a little troublesome.
I have fallen a few times since installation and have not had any breakage or other troubles.
View detail
Fits: YAMAHA YZ125, YAMAHA YZ250, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250F, YAMAHA YZ400F, YAMAHA YZ450F, YAMAHA YZ450FX, YAMAHA YZ250FX
Easy to apply Decal without YAMAHA's stamp
When applying Decal, OEMGuard has a raised YAMAHA imprint, and I bought it because I thought Decal would peel off easily.
It looks good, installs well, and is durable enough when used. No complaints, no excessive interference with the Fork outerTube, and the Decal was easy to put up.
View detail
Fits: INDIAN MOTORCYCLE SCOUT SIXTY, INDIAN MOTORCYCLE SCOUT
dirty
I thought it was Garbage, which is too dirty both in Package and inside.
It was a pain in the ass to return it, so I polished it myself for about an hour.
To the extent that it can be put on, I made it Beauty.
If it's this dirty, I'd rather buy it used and cheap.
View detail
sounding good
I can't do it myself, so the person who did it for me said that FrontSprocket is very good, in terms of material and lightness, etc. Rear sprocket can be attached with either a pure normal thread screw or a taper bolt, according to the specs. View detail
DAYTONA Re-Helmet
I bought this for use after touring. I used to use a Plasma Raster, but the airflow is so much stronger than the Plasma Raster, so I am expecting a Large for use after touring in the middle of summer. View detail
Commendation for the first Leather Boots
As for the size, the instep area seems to be made for a large size, so it is better to adjust the inner sole or the thickness of the socks.
Purchase Size:26.5cm
Size of my normal shoes
・RedWing US9
・NIKE 29cm
・VANS 27.5cm
・VANSSlip-on Silencer US10
Leather is soft and (DoctorMartin rank) I think that even people who have only ever worn Sneakers will be able to wear them without difficulty.
The softness of the leather also makes it easy to operate the Shift Pedal and walk on foot while touring.
On the other hand, the softness of the leather should not be expected to immobilize or protect the ankle in the event of an accident.
The side fastener is very convenient for Large and I can no longer wear Engineer boots without the side fastener!
The sales person at the manufacturer said that the magic tape that guards the fastener is not strong, and if you are careful when storing it, for example, by stopping the magic tape, it should last for a year and a half. Also, the manufacturer can repair it.
Since there is not much information available after the aging process, we have decided to post an Impression.
Overall, get used to it as your first genuine leather Boots, get used to doing Maintenance. (Brush to remove dirt, apply Cream, blow up, WaterproofSpray) It would be good for
The sales person at Manufacturer told me that Cream is better as a basic oil, because if I put only Mink oil on it, it becomes too soft.
View detail
Fits: KTM 500EXC-F, KTM 690EDRR, KTM 450EXC-F, KTM 450SX-F, KTM 350SX-F, KTM 300EXC, KTM 350EXC-F, KTM 250SX, KTM 250SX-F, KTM 250EXC-F, HONDA CRF250R, HONDA CRF450R, YAMAHA YZ250FX, YAMAHA YZ450F, YAMAHA YZ450FX, SUZUKI RMZ250, KAWASAKI KLX230R, KAWASAKI KX250, KAWASAKI KX250F, KAWASAKI KX450
To help us help you.
Product Name
DRC DRC FrontStack Belt
Item Number
D6426
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
5 minutes
Required Tools
Scissors type, etc. would be perfect.
Why did you choose this product?
I chose this one because with this product, I will be able to get help from anyone in case of Race, etc. I also chose this product because of its low price.
Was the one you received as per Image?
It was exactly as shown in the Image. It was more solid than I expected for the price. I hope someone will see this product and help me.
Was the installation difficult?
Installation was not that difficult.
How was your experience with it?
It is not something that you feel particularly when you are running, but I think you will feel glad that you have it in case of an emergency.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Famous Stack Belt
Product Name
TREKFIELD TrekField Stack Belt
Item Number
W-3208-P29696891
Vehicles
Honda CRF125F 2024 MODEL
Number of man-hours
5 minutes
Required Tools
Scissors type, etc. would be perfect.
Why did you choose this product?
I chose this one because I wanted to put a Belt on the Seat to make it easier to move the body when Stacking.
Was the one you received as per Image?
It was just as shown in the Image. I can use this one without any worries.
Was the installation difficult?
It's not particularly difficult, since all you have to do is attach it to the Fork.
How was your experience with it?
The fabric seems to be sturdy, so I think it will be safe. I would also like to try it and see if there are no problems with this one. Also, other people are using it and seem to have no problem with it. I have high expectations for the future.
[Included Parts:were they on?
None in particular.
[Was there anything that disappointed you?
None in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
I am satisfied
Semi-smokeGold
(before a negative form) (not) at all [Color] The color is clear, bright, and appears close to that of the naked eye, which is what I expected.
ARAI is also systematically installed, and anyone can easily install it once they get the hang of it.
View detail
I knew RR had to be this way.
Since we mainly specialize in circuits, we do not need a tough tandem footpeg, so we installed a bracket from the same manufacturer. The silencer is not shaky during driving because of the 5mm thickness of the plate. View detail
[Color] Smoke Screen
Installation was easy, even for an amateur. With a good density, (in Tokyo) I could see in front of me even at night, the Large size was just right, and the wind hit me not hard at all at 100km/highway cruising. View detail
Fits: HONDA SUPER CUBC125, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB
Front feels lighter!
I changed it along with the Front Disc replacement.
The weight is light, but the front tire feels lighter than expected!
The price is reasonable, so if you are not sure, try to replace it.
View detail