Reviews
Mounted on 250DUKE
I was thinking of adding a Carrier in terms of style, but I thought it could be a substitute for a Carrier without a Top case, and also I thought it would be too much of a fussy thing, but I guess it is not so much once you get used to it.
It went on the 250DUKE with no problem, as it should.
When installing, there should be no problem if the entire unit is temporarily assembled while tightening it at the end.
However, it can't be helped that it is Steel, but I think GIVI's Bracket is quite prone to rust in the smallest details.
View detail
Fits: BMW F800, HONDA CB1300SB, HONDA CB400F, HONDA NC700X, KAWASAKI Ninja1000, KAWASAKI Ninja400, KAWASAKI ZX-14R, YAMAHA MT-07, YAMAHA YZF-R25, Others
Standard Large capacity
Installed on klx230sm.
It is still safe to have a Side stay for installation.
The type opens from the side, so it is good that there is no interference even if the Rear back is mounted on top.
Fixing the system requires some ingenuity depending on the type of car, but I think the only way to do that is to devise a solution for each individual car.
View detail
Fits: SUZUKI V-Strom 800 DE
I installed it.
[How is it used?
DL1000 V-STROM800DE Black I installed it in the
Quantity:Pair (for Left and Right) Side case of the
Was the one you received as per Image?
The black color matches the Motorcycle color.
Was the installation difficult?
Installation was easy even by myself, but there was a little hang (order? I had to make a large cut.) I was able to install it easily by myself, but a little bit of hang (order? fit?) was too much.
An assembly Instruction Manual is included, but there are no instructions.
If you only looked at the diagrams in order, you had to start over.
The completed mold must be imaged and installed.
How was your experience with it?
The tight fit between the Frame and Case on the Motorcycle is not good.
From the back, the Right Side looks good, but the Left Side is very tight.
I am using this Manufacturer's stuff for the first time,
I couldn't figure out how to attach Frame and Case since it is not mentioned.
The topCase is compatible with the topCase. If a large topCase is attached, the lid of the attached case will not open.
With 45LtopCase, the Limit lid and the lid opened.
[Included Parts:were they on?
The minimum amount of screws, nuts, and washers required for installation were included.
Washers are not marked with a distinction, so we had to combine them by looking at Screw size and drawings.
Maybe a little puzzle.
Tools are not included and must be prepared by yourself.
[Was there anything that disappointed you?
As I mentioned earlier, the Left Side is difficult to fit.
It is fixed with a fixing component after it is pushed sizzling into the Frame.
View detail
Fits: HONDA CRF250 RALLY, HONDA CRF300 Rally, HONDA CRF250 L, HONDA CRF300 L
Travel to Motorcycle
This is the items needed to install a Hepco&Becker bag. The Instruction Manual is a mess, with pictures, but I couldn't understand it from the pictures. The text is a translation (not "please type here", so let's reopen it).
There are some problems after installation. First, you can't open the Case with the on-board tool, it hits the bracket. The OEM helmet lock does not work, the helmet hits the bracket and does not fit in the lock.
View detail
Parenthesis OK
I bought it because I like the fact that it is not a so-called "top case". I haven't installed it properly yet, but I'm looking forward to it. View detail
Fits: HONDA SUPER CUB110, HONDA SUPER CUB 50, HONDA SUPER CUB110
Easy installation
Used during installation of a homemade box. It was easy to install.
It would be even more appreciated if the included Screw dimensions were 50!
View detail
Easy installation
Simply remove and replace the 6 Bolts around the fuel supply port.
The vSTROM800DE is not compatible, but it arrives without problems.
View detail
I prefer the design to SW-MOTECH's Carrier!
I bought the for Left Side instead of for Right Side because there was a possibility of replacing the Exhaust System.
I am operating this with SW-MOTECH Legend Gear Side bag LC1.
I'm glad I bought this one because it looks great with nothing on it.
Installation is easy, but Torque control and Screw lock application are required.
The price is acceptable because the construction feels very sturdy.
View detail
just right (time, size, length, etc.)
Seat wrapped Belt×Quantity:The 2pc fit just right for Seat.
Fixed Belt secures it in two places and looks pretty good.
It was not difficult.
View detail
I would like a little Pocket.
It has just the right amount of space for a Puncture Repair Kit, rechargeable Compressor, pigskin gloves for work, Wallet, driver's license, Tissues and other small items without expansion.
There is still enough room for two Touring mapple books.
I have not used it in its expanded state, but it has a large sturdy capacity for a day trip touring to a short distance, even if you put a raincoat in it.
When I go on a full-scale touring trip, I will install a separate TrunkBOX and put everything but my wallet and driver's license in it, so this bag will be enough for shopping at the places I stop by.
If possible, it would have been nice to have a Coin Purse or a Small Pocket to hold tolls, tickets, etc.
I have it on my GSR250 and it is just the right height to rest my arm on while waiting at a traffic light.
It may be disturbing when extended.
Also, I am not worried about Magnet gapping at high speeds, but it may be better to give up leaning forward.
It is quite a nuisance, so I will keep one of the Smallest Tank Bag and use it according to the situation.
Touring while looking at Navigation on a cell phone or tablet is fine, but it is fun to drive while looking at a map and getting a little lost, like this.
For those who run at night as well, it is also recommended to buy Small Light and attach it to Fastener.
At any rate, I also popped in Touring mappleR.
View detail
A really nice ‘Mount’.
I purchased this left side 5 litre fuel can holder from Webike and as usual, the service was excellent and the quality of this frame is really impressive. The frame is really well powder coated with fit and finish being the best I've seen with these items. I had to drill two holes to allow the lock assembly to be mounted, but that isn't an issue. The best thing is that I can use panniers still over the top of this frame. A really good product. View detail
Glad I bought it.
I decided to go touring for the first time in a long time, but I couldn't find a fixed Belt. This is a typical symptom of a four-letter Alpha bet!
It's nice that Webike has these products in stock and delivers them immediately. It is very helpful.
Was the one you received as per Image?
It is as per Image.
Was the installation difficult?
There is a loop, so you just wrap it around a good spot on the car body and connect it once the bag is loaded.
How was your experience with it?
It is convenient because it can be removed by simply snapping it off.
I don't think it used to have it, but it has Velcro to wrap the excess Belt.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I will try not to lose it this time.
View detail
GIVI Inner Mat
I installed the Inner Mat on my GIVI commuter scooter. I am satisfied with the size and quality of the mat. View detail
Mounting on HORNET 250
Both capacity and appearance are perfect.
I am glad I bought it because it does not get in the way of my permanent installation.
View detail
GIVI is as it should be.
I am satisfied with both the usability and quality. It is very easy to attach and detach, and I look forward to long touring. View detail
Fits: SUZUKI V-STROM650, SUZUKI V-STROM650XT
Just fit Suzuki V-Strom 650 XT 2023
After several communications with Customer Support regarding fitment, I was able to confirm the fitment and purchased the product. Just fit the car body and I am satisfied. View detail
very good
Very good ?? easy to use! Recommendation around! View detail
Fits: BMW F650GS, BMW F700GS, BMW F700GS, BMW F750GS, BMW F800GS Adventure, BMW F850GS, BMW F850GS Adventure, BMW F900R, BMW F900XR, BMW G650GS, BMW G650GS, BMW G650GS Sertao, BMW K1600 Grand America, BMW K1600B, BMW K1600B, BMW K1600GT, BMW K1600GT, BMW K1600GT, BMW K1600GTL, BMW K1600GTL
About Top caseBack
I am Large satisfied with the capacity without any problems. View detail
Use only LED Lighting Parts
Purchased to add High Mount Stop Lamp to GIVIRear box.
Various parts are included in the kit, but only LED Lamp parts are used.
Installation is easy from the BoxReverse side, and I extended the wiring myself with an Extension Cord to the bottom of the Seat. The wiring does not look good, but it is not visible from the outside.
It is an exclusive product, but the price was a bit high for just the Lamp component.
Reference and
The color of the Base of the BoxBody is more than Red. [Color] Smoke is more noticeable when lit.
Around Lamp (Inside) The reflective material was stretched over the
A hole of approximately 7mm is drilled in an inconspicuous location at the bottom of the Box.
View detail
Cl500
I used a 5 liter bottle with good reviews on Ali, but I thought it would be better if the capacity was larger, so I decided to buy a durable and reliable Japanese product. I chose one with good cost-effectiveness. The outer material is made of durable fabric, and the inner lining is made of waterproof material. The closing side of the carrier is made of hard material. It is the same length as the bag, and the width is about 10cm, so it would be a shame if it were a little wider. The overall shape is a bit pyramid-shaped, and I think it would be useful. I also recommend it because you can always carry a waterproof cover with you. View detail