Reviews
Adjustable sized pulley holder
Almost all the maintenance tools I have to work on my motorcycles are from Kitaco but I went with the one from Special Parts Takegawa for the pulley holder purely because it was cheaper, that might have been a mistake as the red rubber covering has cracked and is damaged already. The pulley holder works well but has now lost some protection from possibly damaging the motorcycle parts. When in use the pulley holder works well and suits many different sized parts, I have used it to remove my oil spinner and flywheel. The clutch will be have some maintenance next so I will be trying out on that too. So in summary a good priced pulley holder but the quality of the rubber covering could be better and would be nice if a replacement covering was available to purchase. View detail
Gear holder in action
As you can see from my photo I have the gear holder in action. Not a big load in it this time as I was just using it this time to stop the crank from spinning while I was removing and installing the centrifugal oil filter cover for its scheduled cleaning. The quality of this tool and the price is fantasic for a tool that will get so much work while carrying out maintenance on your Honda Monkey 125 and the likes. The gear profile in the tool is perfect and left no signs of damage when removed and the short nature of the handle is just right when used i the lower and upper position. Will be used again for my clutch upgrade in the near future. View detail
Ideal for air venting
The price is too good to be true when you consider that it makes air venting a hassle.
I don't think it's a bad idea to buy it.
View detail
Brake fluidfor Replacement
Since one syringe seems to be inconvenient in some way, Quantity:I bought the 2nd pc.
In the trial and error accompanying the first air venting, it was Large active in the work of pressure feeding from Breeder, sucking up the surplus Fluid from Reserver, and the reverse. The beginner is Quantity:I think it's a good idea to have 2pc.
View detail
Can't hold the nail open.
[How is it used?
I used this to replace the Clutch boss on my MT-07.
Was the one you received as per Image?
This is a general Clutch holder. There are several companies that sell the same shape.
How was your experience with it?
The pawl tip format is bad, and when Torque is applied, the Y-shape spreads and the pawl comes off. There is a screw type stopper to control the spread, but it is defeated by Torque.
The reason it spreads is that the tip of the nail is cut at an angle to fit easily into the groove of the Clutch boss.
I had to tighten the Stopper with a water pump ply shop to get it to work. I don't think that's the way it should be used.
[Points to note]
The Clutch boss has a high fastening torque, so if it comes off you could get hurt.
View detail
Fits: HONDA CRF450R, HUSQVARNA TC250, HUSQVARNA TE310, HUSQVARNA TE449, HUSQVARNA TE511, KAWASAKI KX125, KAWASAKI KX250, KAWASAKI KX450F, KAWASAKI KX85, SUZUKI RM250, SUZUKI RM-Z250, HUSQVARNA TE250, KAWASAKI KX250F, SHERCO 500SCF FACTORY, SHERCO 450SCF FACTORY, SHERCO 300SCF FACTORY, SHERCO 250SCF FACTORY, SHERCO 300SC FACTORY, SHERCO 250SC FACTORY, SHERCO 125SC FACTORY
This jig is especially useful for KYB. I'm really glad I purchased it.
This is really useful. There's nothing you can't do without it, but if you have it, you can complete the task quickly.
The structure of the inside of the cup which doesn't scatter Oil around like a water gun, and the angle instantly change, and the air vent is
It's already very convenient. 。 Anodized with a cool finish, it's perfect when it comes to the feeling of owning a tool.
I would like to see a cheaper version with just the functions sold. This is why I reduced the price by 2 stars. I'm sorry.
View detail
These are the Items that are useful to have.
I bought it at the same time when I changed Brake master of ZX-7R to Semi-radial.
I bought this because I thought it would be useful to pull the brake fluid out of the Master Cylinder, but the Caliper on the Left Side
The Fluid came out without any problem, but the Caliper on the Right Side got air from the screw pile of the air breeder and it didn't work well.
I couldn't pull it off.
This is an individual difference, so it can't be helped, but the FluidChanger with the air compressor doesn't pull out the Fluid too much!
However, it is easy to see that the degree of contamination is caused by the air pump.
I dealt with it by wrapping Seal tape around the screw pile of the air breeder. (No more air contamination.)
After replacing the Semi-radial, I put Fluid from the Tank and gripped the Lever to bleed the air, but somewhere in the RightCaliper
I couldn't do anything with the air still mixed in, so I used the air release pump and finished removing the air very easily at once.
I also did some air bleeding by holding the lever just in case, but it was almost unnecessary work.
It's a really useful item if you deal with air contamination from the screw pile of the air breeder.
View detail
I used it for Spring Tensile on Center Stand!
I purchased this to pull and install the OptionOEMCenter Stand Spring on my vehicle.
It is one of the products that it is convenient when there is it though the appearance is few.
View detail
It's very strong.
It is a durable spring hook that can pull even the strongest spring. The hook body is made of Plating and the quality is very good. View detail
Kitaco Gear Holder For Monkey Maintenance
I do like purchasing tools almost as much as purchasing upgraded parts for the motorcycle and when the tool is such a useful one and quality item like this product I am always so happy. The gear holder is only a small item but extremely useful when working on the Monkey 125 and this item has now replaced the coin I was using before which always fell out of the gearing and landed in the wrong places. I can never complain about the price and quality of the Kitaco tools I have purchased so far and I will continue to purchase from them as needed. I do recommend this tool for the DIY mechanic. I know a lot of people do not like spending money on tooling but the right tools always make the job easier. View detail
![[Aebs] BALANCER Weight Hammer](https://img.webike-cdn.net/catalogue/19270/07261054_51f1d6e0d216b_TS.jpg)
Convenient for Tire replacement
It is very useful for both Aluminum and Steel wheels when using the Tire Replacement Wheel Balancer. View detail
CB250R
I bought this product for Front fork oil level adjustment of CB250R.
There is a little rattling, but it can be used without a problem.
It is convenient to use Torque wrench.
View detail
Was good
This is the first time I've done a Wiring hollow through. I was surprised at how easy it was to open. I think it is good to have it. View detail
It's not cheap.
[How is it used?
Quantity of Fork oil level:Pair (for Left and Right) facing
Was the one you received as per Image?
Yes
How was your experience with it?
Quantity:Pair (for Left and Right) A sense of security that the
[Points to note]
Be sure to bleed the air
How did it compare to other products?
Basically the same as the one I used at my parents' house.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
nothing in particular
View detail
Good work.
I was able to work with peace of mind because of the solid construction. View detail
The strength of the product is reliable.
The price may be a little cheaper, but for the appearance, it is strong and durable. You can pull the hard spring and prevent the exhaust system from being scratched and you can use it safely. View detail
Thanks for this product.
Turn round and round to change the length.
If you measure the length when you remove the R suspension and adjust it to about that length, it is Large strong.
I just put this on in place of the R suspension I removed to get the Maintenance out.
Not having to leave Motorcycle in RoseRose is more convenient than expected.
The person who commercialized this. Really great.
View detail
Was good
I'm glad I got it at a reasonable price, I used it for the Wiring middle passage and I think it's so easy to drill even if you can't come. It is very easy to make a hole. View detail
![[AEBS] Universal Holder For HONDA](https://img.webike-cdn.net/catalogue/images/22527/02261430_530d7c0aa1c76_TS.jpg)
It's cheap, but it works.
I replaced the DAYTONA one I used when I was a beginner, because it was getting damaged. 。 I can use it normally 。 The direction of the clamping is different from DAYTONA's.:Pair (for Left and Right) It is different, but there is no problem in JF31. View detail
SHOWAFork Maintenance
I thought about making a simple tool, but I bought it as a dedicated tool considering the regular replacement of the oil seal.
When used in conjunction with the Electric Impact, I was able to disassemble the Showafork in no time. I'm glad I bought it because the cost is well worth it and it's easy to work with.
I used it by holding it between my legs because it didn't stand stable, but later I saw that the plate to hold it in a vise is welded, so I think I will fix the Tool in a proper place when I use it next time.
View detail